RoadVitals

1995 Advance Truck Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
Recall campaignsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
2
Newest Aug 8, 1996
Carrying an NHTSA advisoryCampaigns where NHTSA told owners not to drive the vehicle, or to park it outside, until the repair is done.
0
Open investigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0

Recall campaigns

2 campaigns cover this model year — what the defect is, what it could cause, and what the remedy is

96V124005

SUSPENSION

Aug 8, 1996
538 units potentially affected
The defect: THE EQUALIZING BEAM SHAFT OF THE TANDEM AXLE SUSPENSION WERE MANUFACTURED FROM AS-ROLLED SAE4140 STEEL RATHER THAN THE SPECIFIED ANNEALED SAE4140. THESE SHAFTS CAN FRACTURE INSIDE THE BEAM AT THE TOE OF THE WELD.
The risk: VEHICLES ARE SUBJECT TO VEHICLE TILT AND POSSIBLE ROLLOVER IN THE EVENT THAT BOTH EQUALIZING BEAMS, ON THE SAME SIDE OF THE VEHICLE, EXPERIENCE A SIMULTANEOUS SHAFT FAILURE. AFFECTED SUSPENSIONS CAN ALSO DROP AND CONTACT THE ROAD SURFACE GENERATING SPARKS WHICH COULD IGNITE FLAMMABLE MATERIAL.
The remedy: OWNER NOTIFICATION IS BEING CONDUCTED BY NEWAY ANCHORLOK. DEALERS WILL INSPECT AND REPLACE ALL SUSPENSION SUSPENSION BEAMS WITH SUSPENSION BEAMS CONTAINING APPROPRIATE SHAFTS.
ADVANCE MIXER, INC.View on NHTSA.gov
95E002002

SERVICE BRAKES, AIR:DRUM

Jun 8, 1995
28 units potentially affected
The defect: THE MACHINING PERFORMED ON THE BRAKE DRUMS WILL NOT PERMIT THE DRUM TO SEAT FULLY AGAINST THE HUB FACE. THE REDUCED BRAKE DRUM AND HUB CONTACT AREA WILL ABRADE AND FRET ALLOWING THE WHEEL MOUNTING JOINT TO LOOSEN.
The risk: THE WHEEL MOUNTING STUDS CAN BREAK RESULTING INSEPARATION OF THE WHEEL FROM THE VEHICLE. VEHICLE STEERING AND BRAKING WILL BE REDUCED AND THE SEPARATED WHEEL WOULD CAUSE A HAZARD TO OTHERS ON THE HIGHWAY. EITHER EVENT CAN RESULT IN A VEHICLE ACCIDENT.
The remedy: DEALERS WILL REPLACE THE INCORRECTLY MACHINED DRUMS WITH NEW BRAKE DRUMS SUPPLIED BY ROCKWELL AND ALSO REPLACE THE WHEEL MOUNTING STUDS.
ADVANCE MIXER, INC.View on NHTSA.gov

What a recall is

Safety recall
A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation
NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Elsewhere on this vehicle

Data sources