2007 BMW 525I Problems

The contact owns a 2007 BMW 535I. The contact stated that while operating the vehicle, the passenger’s side air bag warning light remain illuminated, indicating a possible failure to the air bag system. The cause of the failure was not yet determined. The local dealer was notified of the failure. The manufacturer was not yet notified. The failure mileage was 100,000.

The contact owns a 2007 BMW 525I. The contact stated that the air bag warning light was illuminated. The dealer was notified of the failure. The vehicle was not diagnosed nor repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 102,000.

I purchased said automobile from my neighbor for my son to drive. I figured it was a good car to buy because it was serviced by Hendrick BMW (Charlotte, NC) only and regularly. BMW's also have a reputation for being safe as well as reputable so this also weighed into my decision. Fast forward 18 months. The passenger rear brake bulb went out. We replaced the bulb, it worked for a short time, then went out. We replaced the bulb again. This time it didnt work. About a week later the front passenger side head light went out, then the other side. We took it to Hendrick BMW for repair. Hendrick has told us the car wiring basically needs to be replaced due to the protective coat wearing off and corroding the bare wire underneath. The headlights/ brake light will also need to be replaced due to the corrosion blowing out the bulb. For the front headlight the whole assembly needs to be replaced at a tremendous cost. I performed a google search on this and found many, many instances of the same issue. Ive seen many of these cars while casually driving around town. It would seem to be a MAJOR issue if an active drivers head and tail lights suddenly stopped working on a busy road. Also due to the cost most people probably wouldnt fix the issue on their own and drive the car anyway causing an ever bigger safety issue. I have never had this issue with any other vehicle brand ive owned. Ive looked into this issue with other brands and most tell me they use wiring which will not do this. I am not sure why BMW would not do the same. The car is also up for inspection. The car will not pass inspection unless I pony up over $6k ($2500 NADA value) to fix. My taxes are also due. In NC you cant pay the tax unless the car passes inspection. This is costing me daily penalties in addition to the major safety issue. I believe the NHTSA has a duty to look into this major manufacturing defect and have BMW provide remedy to those other unfortunate folks who are experiencing the same issue.

HEADLIGHT WIRING INSULATION ROT LEAD TO FAILED HIGH AND LOW BEAMS ON DRIVER SIDE AND INTERMITTENT FAILURES OF BOTH BEAMS ON PASSENGER SIDE. SEE PHOTO FOR EXAMPOLE OF DISINTEGRATED WIRING ON DRIVER HIGH BEAM WIRING HARNESS. ONLY KNOWN OPTION IS TO BUY A COMPLETE NEW HEADLIGHT ASSEMBLY ($1250+ PER SIDE) OR ATTEMPT DIY. THIS PROBLEM IS WELL-KNOWN AND HAS LONG BEEN REPORTED BY OTHER BMW E60 (5 SERIES 2004-2010) OWNERS AT BIMMERFEST.COM AND 5SRIEST.NET. SEE THESE URLS FOR MORE INFORMATION: HTTPS://WWW.BIMMERFEST.COM/FORUMS/SHOWTHREAD.PHP?T=798640 HTTPS://WWW.BIMMERFEST.COM/FORUMS/SHOWTHREAD.PHP?T=883000 HTTPS://5SERIES.NET/FORUMS/E60-E61-PARTS-ACCESSORIES-MODS-22/OPENING-UP-E60-HEADLIGHTS-138473/

LIGHTS OF THE STEERING WHEEL ITS BEEN LOCK CAME OUT, THE CAR WAS PARK AND WAS READY TO GO TO WORK, BUT WHEN I TURNED ON THE LIGHT SHOW UP ON THE PANEL, AND THE STEERING WHEEL WAS NOT LOCK, I WAS ABLE TO TURN IT,, I TURN IT OFF AND ON AGAIN AND THE LIGHT STILL ON

THE CAR WILL NOT START, A STEERING LOCK MALFUNCTION AND A ENGINE MALFUNCTION MESSAGE APPEAR. HAD BMW MECHANICS TRY TO RESOLVE PROBLEM. CHANGED STEERING LOCK MECHANISM, REPROGRAM MODULES, CHANGE SEVERAL SENSORS, PLACE NEW BATTERY AND EVEN REPLACE THE DME. THE ONLY THING THAT SEEMS TO PARTIALLY ALLOW THE CAR TO START IS TO "RESET THE CAS" WITH A COMPUTER.

The contact owns a 2007 BMW 525I. The contact received notification of NHTSA Campaign Number: 22V119000 (Engine and Engine Cooling). The vehicle was taken to the dealer for the recall repair however, upon retrieving the vehicle, the contact noticed that the vehicle was shaking while driving at various speeds. The contact stated that the failure had worsened while at a complete stop. Over time, the service engine warning light illuminated. The dealer was notified of the failure and the contact was placed on an indefinite hold until the call disconnected. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was 284,191.

The contact owns a 2007 BMW 525i. The contact stated that while driving at approximately 75-85 MPH, she smelled smoke coming from the hood of the vehicle. The contact was unsure if any warning lights illuminated. The vehicle was taken to an independent mechanic where he referenced NHTSA Campaign Number: 22V119000 (Engine And Engine Cooling) , but the vehicle was not diagnosed for the failure. The dealer was not notified of the failure. The manufacturer was not notified of the failure. The approximate failure mileage was 189,000.

BOUGHT THE CAR IN AUG STARTED USING THE SEAT WARMER ABOUT DECEMBER OF 2014. HERE AND THERE UPON USING I'D SMELL SOMETHING BURNING SO I WOULD TURN IT OFF! BUT NOT ALL THE TIME WHEN USING THE WARMER DID I SMELL BURNING! LATE MARCH MY HUSBAND NOTICED A BURN HOLE ON MY DRIERS SEAT, I INSTANTLY REMEMBERED THE BURNING SMELL WHEN SOMETIMES USING THE SEAT HEATER! I'M LUCKY I WAS NOT BURNED BUT MY DRIVER SEAT IS RUINED AND I'M NOW AFRAID TO USE THE HEATERS, EVER! *TR

TL* THE CONTACT OWNS A 2007 BMW 525I. THE CONTACT STATED THAT THE FRONT DRIVER SIDE ELECTRONIC SEAT CONTROL SWITCH WOULD REVERSE WHEN THE CONTACT ATTEMPTED TO MOVE THE SEAT FORWARD. THE DEALER REPLACED THE SWITCH ASSEMBLY. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 73,000.

MY WARNING LIGHT "FAULT IN THE PASSENGER RESTRAINT SYSTEM" ILLUMINATED WHEN I TURNED THE CAR ON. HAS NOT COME OFF.

PASSENGER RESTRAINT FAILURE WARNING CAME UP ON MY 2007 525I. THIS HAS BEEN A PROBLEM ON PREVIOUS MODELS BUT AFTER TAKING MY VEHICLE INTO THE DEALERSHIP THEY INFORMED ME IT WOULD NOT BE COVERED AND WOULD COST ME ROUGHLY $2000 TO REPAIR. THIS IS A SEVERE SAFETY ISSUE AS NOBODY CAN RIDE IN THE PASSENGER SEAT. THIS SHOULD BE COVERED WITH THE OTHER VEHICLES. *TR

I purchased said automobile from my neighbor for my son to drive. I figured it was a good car to buy because it was serviced by Hendrick BMW (Charlotte, NC) only and regularly. BMW's also have a reputation for being safe as well as reputable so this also weighed into my decision. Fast forward 18 months. The passenger rear brake bulb went out. We replaced the bulb, it worked for a short time, then went out. We replaced the bulb again. This time it didnt work. About a week later the front passenger side head light went out, then the other side. We took it to Hendrick BMW for repair. Hendrick has told us the car wiring basically needs to be replaced due to the protective coat wearing off and corroding the bare wire underneath. The headlights/ brake light will also need to be replaced due to the corrosion blowing out the bulb. For the front headlight the whole assembly needs to be replaced at a tremendous cost. I performed a google search on this and found many, many instances of the same issue. Ive seen many of these cars while casually driving around town. It would seem to be a MAJOR issue if an active drivers head and tail lights suddenly stopped working on a busy road. Also due to the cost most people probably wouldnt fix the issue on their own and drive the car anyway causing an ever bigger safety issue. I have never had this issue with any other vehicle brand ive owned. Ive looked into this issue with other brands and most tell me they use wiring which will not do this. I am not sure why BMW would not do the same. The car is also up for inspection. The car will not pass inspection unless I pony up over $6k ($2500 NADA value) to fix. My taxes are also due. In NC you cant pay the tax unless the car passes inspection. This is costing me daily penalties in addition to the major safety issue. I believe the NHTSA has a duty to look into this major manufacturing defect and have BMW provide remedy to those other unfortunate folks who are experiencing the same issue.

HEADLIGHT WIRING INSULATION ROT LEAD TO FAILED HIGH AND LOW BEAMS ON DRIVER SIDE AND INTERMITTENT FAILURES OF BOTH BEAMS ON PASSENGER SIDE. SEE PHOTO FOR EXAMPOLE OF DISINTEGRATED WIRING ON DRIVER HIGH BEAM WIRING HARNESS. ONLY KNOWN OPTION IS TO BUY A COMPLETE NEW HEADLIGHT ASSEMBLY ($1250+ PER SIDE) OR ATTEMPT DIY. THIS PROBLEM IS WELL-KNOWN AND HAS LONG BEEN REPORTED BY OTHER BMW E60 (5 SERIES 2004-2010) OWNERS AT BIMMERFEST.COM AND 5SRIEST.NET. SEE THESE URLS FOR MORE INFORMATION: HTTPS://WWW.BIMMERFEST.COM/FORUMS/SHOWTHREAD.PHP?T=798640 HTTPS://WWW.BIMMERFEST.COM/FORUMS/SHOWTHREAD.PHP?T=883000 HTTPS://5SERIES.NET/FORUMS/E60-E61-PARTS-ACCESSORIES-MODS-22/OPENING-UP-E60-HEADLIGHTS-138473/

WE WOULD LIKE THE NHTSA TO BE AWARE THAT MYSELF AND A FEW COLLEAGUES OWN BMW AND HAVE EXPERIENCED THIS ISSUE. BMW HAS PURPOSELY BUILT THESE VEHICLES TO FAIL AFTER THE WARRANTY PERIOD WHEN A FEW MONTHS AFTER THE 100,000 MILE WARRANTY WE BEGAN HAVING PROBLEMS SPECIFICALLY WITH THE SEALS AROUND ALL ALL WINDOWS INCLUDING WINDSHIELD AND REAR WINDOW AS WELL AS THE SEALS AROUND THE TRUNK, HOWEVER AT THE BOTTOM OF THE TRUNK BMW KEEPS A MAIN COMPONENT BOARD UNDERNEATH THE SPARE TIRE , ONCE THE SEALS BEGIN TO FAIL IT CAUSES WATER AND MOISTURE TO GAIN ACCESS TO THIS COMPARTMENT AND CAUSE THE BOARD TO IGNITE AND CATCH FIRE AND CAUSE CAR TO GO CRAZY WITH ACCELERATION AND DECELERATION, WHY PLACE A MAIN COMPONENT IN THIS LOCATION WITH 10 FEET OF EXTRA WIRE AND NO DRAIN, I WOULD ALSO LIKE TO POINT OUT ALL BMW'S OF THE SAME YEAR EXPERIENCE M MELTING OF THE PLASTIC INTERIOR PARTS AND THE PAINT TO COMPLETELY BREAK DOWN UNDERNEATH THE CLEAR COAT NO MATTER HOW MUCH AX IS APPLIED THESE ARE MAJOR FLAWS AND BMW IS WELL AWARE OF THEM, THERE VEHICLES AND SERVICE IS TERRIBLE THEY SHOULD NOT BE ALLOWED ON THE ROAD

TRUNK LOCKING FAILURE. UNABLE TO OPEN TRUNK WITH REMOTE CONTROL OR SWITCH INSIDE THE CAR. I WAS ONLY ABLE TO OPEN THE TRUNK WITH THE KEY OVER-RIDE FROM THE TRUNK. BMW USA CUSTOMER SERVICE DID NOT PROVIDE ANY ASSISTANCE TO OPEN THE TRUNK. I HAD TO READ THE MANUAL TO BE ABLE TO OVER-RIDE THE ELECTRICAL SYSTEMS. ONCE I OPENED THE TRUNK THE TRUNK WOULD NOT CLOSE. AFTER EXTENSIVE INTERNET RESEARCH AND ELECTRICAL TROUBLE-SHOOTING, I FOUND BROKEN BROWN ELECTRICAL WIRE IN THE TRUNK HARNESS BOOT ABOVE THE BATTERY COMPARTMENT. I FOUND SEVERAL CASES POSTED IN THE INTERNET. THIS IS A COMMON PROBLEM WITH BMW. BMW USA CUSTOMER RELATIONS WAS CONTACTED TO REPORT THIS SAFETY ISSUE AND A DESIGN FLOW BUT SHE DID NOT OFFER ANY INTEREST TO RESOLVE THE ISSUE. I OFFERED THE OPPORTUNITY TO BMW TECHNICIANS / ENGINEERS TO INSPECT THE DESIGN FLOW AND PERHAPS THEY CAN PROVIDE A SOLUTION TO THIS DEFECT BUT SHE WANTED ME TO GO TO THE DEALER AND PAY THE DEALER TO DIAGNOSE THE PROBLEM ($150 PER HOUR FEE). I WAS CLEAR THAT I ALREADY FOUND THE PROBLEM AND CAN SIMPLY SPLICE THE WIRES BACK BUT I WAS CALLING BECAUSE I AM CONCERN ABOUT THE SAFETY OF OTHER BMW DRIVERS. ELECTRICAL SHORTAGE NEXT TO THE BATTERY CAN BE A SAFETY CONCERN! BMW CUSTOMER SERVICE MANAGER DID NOT OFFER ANY HELP EITHER. *TR

I WAS DRIVING MY 2007 BMW 525I ON A CITY STREET AND WHEN I ATTEMPTED TO STOP AT A STOP SIGN THE BRAKES WERE NON EXISTENT. THE BRAKE PEDAL LOST ALL OF ITS PRESSURE AND WENT ALL THE WAY DOWN WITHOUT STOPPING THE VEHICLE. I COULD NOT STOP AT THE STOP SIGN AND THE ONLY WAY TO STOP WAS USING THE EMERGENCY BRAKE WHICH BARELY STOPPED THE VEHICLE. THE BRAKES WOULD NOT WORK SO I WAS UNABLE TO DRIVE THE VEHICLE. AFTER FURTHER INSPECTION UNDER MY HOOD, I FOUND A BROKEN BRAKE VACUUM HOSE WHICH BROKE APART AND THIS WAS THE CAUSE OF THE BRAKE SYSTEM FAILURE. I WAS VERY LUCKY NOT TO BE INJURED.

WHEN I REALIZED A LIGHTBULB IN MY HEADLIGHTS WENT OUT I BOUGHT THE BULB ONLINE READY TO REPLACE IT. I REALIZED WHEN REPLACING THAT THE WIRES CONNECTING TO THE HEADLIGHTS ARE COMPLETELY FLAKED OFF. SO I WANTED MONEY ON A NEW BULB BECAUSE IT WON'T LIGHT UP REGARDLESS. NOW THIS NOT ONLY CAUSES THE BULB TO NOT WORK BUT IT MESSES WITH THE LIGHTS IN THE WHOLE SIDE OF THE HEADLIGHT. MY ENTIRE LEFT HEADLIGHT TWEAKS. SOMETIMES JUS ONE PARKING LIGHT IS OUT, THEN IT'S THE HIGH BEAM THAT DOESN'T WORK, THEN IT'S THE LOW BEAM. SOMETIMES WHEN I HAVE LOW BEAMS ON THE LEFT HEADLIGHT HAS ITS HIGH BEAMS ON BY ITSELF. ALL THIS HAPPENED BECAUSE I TRIED TO CHANGE A BULB AND THE WIRINGS JUS FLAKED OFF AS SOON AS THEY MOVED OR BENDED A BIT. THIS IS VERY DANGEROUS BECAUSE MY HEADLIGHT WON'T WORK SOMETIMES AND THAT MAKES ME NOT SO VISIBLE AT NIGHT. ALSO I END UP UNINTENTIONALLY HAVING MY HIGH BEAMS ON WITH NO WAY FOR ME TO TURN IT OFF BESIDES COMPLETELY TURNING OFF MY HEADLIGHTS. PRETTY SURE IT'S AN ELECTRICAL OR FIRE HAZARD TOO TO HAVE A BUNCH OF NAKED WIRES SIDE BY SIDE. FAULT NUMBER 2 IS THE BRAKES. WHEN COMING TO COMPLETE STOP MY CAR JERKS. THERE'S NOTHING WRONG WITH THE BRAKE SYSTEM. I TALKED TO A COUPLE PEOPLE WITH THE SAME MODEL CAR AS ME AND THEY ALL HAD THE SAME PROBLEM. IT JUST HAPPENS ONCE THE CAR GETS TO A HIGH NUMBER OF MILES. SOMETHING SHOULD BE DONE ABOUT THIS BECAUSE A FUNCTIONAL CAR SHOULDN'T BE JERKING WHEN COMING TO A STOP. ESPECIALLY IF THE BRAKES ARE IN PERFECT CONDITION.

TRANSMISSION GOES IN TO SAFE MODE SUDDENLY ON THE FREEWAY AT HIGH SPEED RANDOMLY AND SLOWS DOWN MAKING IT DANGEROUS SITUATION. CODE P17EC .

TRANSMISSION JERKS AND THE CAR GIVES A KICK WHEN THE CAR AUTOMATICALLY DOWNSHIFTS FROM 2 TO 1. THIS TYPICALLY HAPPENS WHEN SLOWING DOWN TO A STOP. SEEN MANY REFERENCES OF TRANSMISSION JERK / KICK ISSUES ONLINE ON BIMMERFEST. REPORTS TO BMW USA AS WELL. BMW USA REFUSES TO ASSIST WITH THIS ISSUE. *TR

TRANSMISSION JERKS WHEN VEHICLE IS ABOUT TO STOP, DOWNSHIFTING TRANSMISSION ISSUE FROM 2 TO 1 SPEED. *TR

THE CONTINENTAL TIRES AKA AS " CONTITOURING CONTACT CV95" ARE WEARING OUT PRETTY BAD WITH JUST 23000 MILES ON IT. I HAVE NOTICED WAVING INSIDE THE WALLS OF THE TIRES AND ONE OF THEM ACTUALLY STARTED TO COME APART. I HAVE BEEN DOING RESEARCH ON LINE REGARDING THIS PARTICULAR TIRE FROM CONTINENTAL WITH SIMILAR COMPLAINS AS MINE, AND IT APPEARS CONTINENTAL IS BLOWING PEOPLE OFF, AND THE AUTO DEALERS ARE NOT TAKING RESPONSIBILITY EITHER. AS FOR ME I BELIEVE THE TIRE SENSOR ON MY BMW COULD HAVE SAVE OUR LIVES. UPON GETTING A TIRE PRESSURE READING I PULLED OVER, FELT THE TIRES AND FOUND THE LEFT REAR TIRE WITH RIPPLES AND THE INSIDE TREADING COMING APART. I HAD JUST BEEN TRAVELING AT SPEEDS OF UP TO 70 MILES WITH MY WIFE AND CHILDREN IN THE CAR. I HAVE CONTACTED CONTINENTAL VIA E-MAIL AND DO NOT EXPECT ANY RESPONSE SINCE SIMILAR PEOPLE HAVE COMPLAINED AND I HEAR CONTINENTAL TIRES IS NOT RESPONDING TO PEOPLE'S CONCERNS. THIS IS SCARY AND SOMETHING SHOULD BE DONE ABOUT IT. THANKS *TR

TL*THE CONTACT OWNS A 2007 BMW 525I. WHILE DRIVING APPROXIMATELY 75 MPH, THE TRANSMISSION WARNING LIGHT ILLUMINATED ON THE INSTRUMENT PANEL AND THE TRANSMISSION BEGAN TO SLIP. THERE WAS ALSO A VERY LOW POWER RESPONSE WHEN ACCELERATING. THE WARNING INDICATOR REMAINED ILLUMINATED UNTIL THE ENGINE WAS TURNED OFF. THE VEHICLE WAS TAKEN TO AN AUTHORIZED DEALER FOR DIAGNOSTIC TESTING AND THEY DETECTED FAILURE WITHIN THE COMPUTERIZED SYSTEM. THE VEHICLE WAS REPAIRED, BUT THE FAILURE RECURRED. THE VEHICLE HAS NOT BEEN REPAIRED AGAIN. THE VIN WAS UNKNOWN. THE FAILURE MILEAGE WAS UNKNOWN AND THE CURRENT MILEAGE WAS 18,000.

I purchased said automobile from my neighbor for my son to drive. I figured it was a good car to buy because it was serviced by Hendrick BMW (Charlotte, NC) only and regularly. BMW's also have a reputation for being safe as well as reputable so this also weighed into my decision. Fast forward 18 months. The passenger rear brake bulb went out. We replaced the bulb, it worked for a short time, then went out. We replaced the bulb again. This time it didnt work. About a week later the front passenger side head light went out, then the other side. We took it to Hendrick BMW for repair. Hendrick has told us the car wiring basically needs to be replaced due to the protective coat wearing off and corroding the bare wire underneath. The headlights/ brake light will also need to be replaced due to the corrosion blowing out the bulb. For the front headlight the whole assembly needs to be replaced at a tremendous cost. I performed a google search on this and found many, many instances of the same issue. Ive seen many of these cars while casually driving around town. It would seem to be a MAJOR issue if an active drivers head and tail lights suddenly stopped working on a busy road. Also due to the cost most people probably wouldnt fix the issue on their own and drive the car anyway causing an ever bigger safety issue. I have never had this issue with any other vehicle brand ive owned. Ive looked into this issue with other brands and most tell me they use wiring which will not do this. I am not sure why BMW would not do the same. The car is also up for inspection. The car will not pass inspection unless I pony up over $6k ($2500 NADA value) to fix. My taxes are also due. In NC you cant pay the tax unless the car passes inspection. This is costing me daily penalties in addition to the major safety issue. I believe the NHTSA has a duty to look into this major manufacturing defect and have BMW provide remedy to those other unfortunate folks who are experiencing the same issue.