RoadVitals

1996 BMW R1100 Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Data refreshed

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
Recall campaignsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
1
Newest Dec 31, 1997
Carrying an NHTSA advisoryCampaigns where NHTSA told owners not to drive the vehicle, or to park it outside, until the repair is done.
0
Open investigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0
1 investigation on file

Recall campaigns

1 campaign cover this model year — what the defect is, what it could cause, and what the remedy is

97V237000

ELECTRICAL SYSTEM:WIRING

Dec 31, 1997
2,000 units potentially affected
The defect: VEHICLE DESCRIPTION: MOTORCYCLES. A SHEET METAL PLATE MOUNTED TO THE FRONT OF THE FRAME BELOW THE INSTRUMENT CLUSTER CAN CAUSE THE WIRING HARNESS TO BE STRETCHED TOO TIGHT AS THE HANDLEBARS ARE TURNED FULLY TO ONE SIDE. IN ADDITION, THE WIRING HARNESS IS ATTACHED TO ANOTHER HARNESS WITH A CABLE TIE THAT IS PLACED TOO FAR FORWARD LIMITING THE HANDLEBAR MOVEMENT.
The risk: THE HARNESS WIRES CAN BE DAMAGED OR COULD BREAK OR PULL OUT OF THE IGNITION SWITCH. IF THE HARNESS WIRES WERE DAMAGED BUT NOT BROKEN OR DISCONNECTED, THE ELECTRICAL SYSTEM COULD BE AFFECTED WHILE THE MOTORCYCLE IS BEING DRIVEN. HESITATION, MISFIRING, OR "CUTTING OUT" COULD OCCUR INCREASING THE RISK OF A VEHICLE CRASH.
The remedy: DEALERS WILL RELOCATE THE WIRE TIE CONNECTING THE TWO WIRING HARNESSES TO A POINT FURTHER BACK FROM THE ORIGINAL LOCATION SO THAT THE IGNITION SWITCH WIRING HARNESS HAS SUFFICIENT FREEDOM OF MOVEMENT. ALSO IF THE WIRING HARNESS IS FOUND TO BE DAMAGED, THE IGNITION SWITCH (WITH HARNESS) WILL BE REPLACED.
BAYERISCHE MOTOREN WERKEView on NHTSA.gov

What a recall is

Safety recall
A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation
NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Safety investigations

NHTSA inquiries naming this vehicle. An investigation is not a finding of a defect, and it is not a recall.

SQ97022ClosedInvestigation

STEERING LOCK/IGNITION SWITCH WIRING

Opened Nov 14, 1997
Closed Dec 31, 1997

BMW WILL CONDUCT A SAFETY RECALL TO REMOVE THE SHEET METAL PLATE AND RELOCATE TWO WIRING HARNESSES SO THAT THE IGNITION WIRING HARNESS HAS SUFFICIENT FREEDOM OF MOVEMENT THROUGHOUT THE RANGE OF MOTION OF THE HANDLEBARS.WIRING HARNESSES FOUND DAMAGED, WILL BE REPLACED.NO FURTHER ACTION IS NECESSARY.THIS INVESTIGATION IS CLOSED.

STEERING

Elsewhere on this vehicle

Data sources

Data on this page last refreshed .