1998 BMW Z3 Problems

SEATS MOVE FORWARD AND BACKWARD WHEN VEHICLE ACCELERATES OR DECELERATES, ITS A KNOWN ISSUE OF DEFECTIVE EQUIPMENT THAT SHOULD NOT FALL ON THE CONSUMER FOR REPAIR

TL*THE CONTACT OWNS A 1998 BMW Z3. DURING ACCELERATION AND DECELERATION THE FRONT PASSENGER AND DRIVER SEAT ADJUSTOR RAIL FAILED. AS A CONSEQUENCE, THE SEAT MOVED BACK AND FORTH WHILE THE CONTACT WAS DRIVING. THE VEHICLE WAS TAKEN TO THE DEALER FOR INSPECTION, BUT NO REPAIRS WERE MADE. THE FAILURE MILEAGE WAS 50,000. THE CURRENT MILEAGE WAS 65,000. UPDATED 11/09/09 *BF THE CONSUMER STATED BMW KNEW THERE WAS A PROBLEM AND THERFORE, THEY CHANGED MATERIAL USED IN THE ISOLATER PADS. UPDATED 11/09/09

SAFETY DEFECT 1998 Z3 BMW. *MR THE AIR BAG LIGHT WAS CONSTANTLY ILLUMINATED. THE VEHICLE WAS TAKEN TO THE DEALER WHO PERFORMED A DIAGNOSTIC CHECK. THE CHECK INDICATED THAT THE SAFETY RESTRAINT SYSTEM WAS GETTING ELECTRICAL INTERFERENCE IN THE WIRING HARNESS. THE CONSUMER REFUSED REPAIR DUE TO THE COST AND CONTACTED THE MANUFACTURER FOR ASSISTANCE. THE MANUFACTURER REFUSED ANY ASSISTANCE BECAUSE THE VEHICLE WAS OUT OF WARRANTY. THE CONSUMER BELIEVES THAT SINCE THIS IS A SAFETY RELATED PROBLEM THAT IT SHOULD BE REPAIR AT NO CHARGE. *NM

THE VEHICLE AIR BAG LIGHT ILLUMINATED. THE CONSUMER WAS INFORMED BY THE DEALER THAT THE PROBLEM WAS DUE TO ELECTRICAL INTERFERENCE IN THE WIRING HARNESS. THE DEALER WANTED THE CONSUMER TO PAY $400 TO REPAIR THE PROBLEM BUT THE CONSUMER BELIEVES BMW SHOULD BE RESPONSIBLE. THE CONSUMER IS CONCERNED THAT THIS PROBLEM MAY CAUSE THE AIR BAG TO FAIL ON IMPACT. *AK *NLM

WHILE BRAKING AND SPEEDING THE DRIVER'S SEAT LURCHED FORWARD/BACKWARDS ON THE SEAT TRACKS. DEALERSHIP WAS NOTIFIED, BUT DID NOT RESOLVE THE PROBLEM. *AK

THE DRIVER WAS STOPPED AT A LIGHT WHEN THE VEHICLE WAS IMPACTED IN THE FRONT AT 45 MPH. NEITHER OF THE FRONTAL AIR BAG DEPLOYED. THE SEAT BELT ALSO FAILED TO PROPERLY RESTRAIN THE DRIVER. *AK *CB *NLM

The BMW E36 Z3 1996-2002 (I have the 1998 1.9) are prone to having a separation of the Rear subframe from the differential causing the drivetrain to hang off the vehicle and/or rip out of the trunk's weak aluminum sheet subframe. BMW Germany has acknowledged the problem for a few individuals over the past decade and a half and kept it on the low for them to not spread it further. BMW North America fails to acknowledge the design flaw during their manufacturing process in the North American Plant during the late 90s. The Spot Welds' quality is subpar and worrisome as this catastrophic failure of the subframe to driveline structure has various ways of presenting it self which chiefly includes popped spot welds in the truck which comes hand in hand with a cracked differential ear bracket. * To simply understand why this happens: The issue is that the metal of the trunkfloor is too thin and not adequete at holding up to the forces of the differential tugging at it. There have been documented cases of similarly "repaired" Z3's that end up basically pulling out and/or deforming the entire trunkfloor panel. The metal panel the diff crossmember is structurally tied to (and the trunkfloor itself which is above it) is simply too weak for the forces being applied through it. Adding more welds simply changes where the failure occurs - from pulling out spotwelds, to deforming the trunk floor/crossmember itself if there are too many welds for them to be able to be pulled out. There are a few kits going around that other owners have addressed to their vehicles for a few thousand dollars which includes welding and a re-fabrication of the trunk floor's structure to the subframe/chasis. It has two "caps" that sit on the framerails at either side and a "crossmember" piece which is a strong piece of metal that spans between the two frame rails and sits on top of the "caps". When installed, the differential ends up tugging at the crossmember, which then distributes the forces.....

I HAVE A 1998 Z3 M ROADSTER AND THE TRUNK WELDS HOLDING THE SUBFRAME IS FAILING. THIS IS A COMMONLY DOCUMENTED ISSUES. BMW DEALERS ACKNOWLEDGE THE ISSUE BUT BMW NORTH AMERICA WILL NOT FIX IT. THIS IS A WELDING/MANUFACTURING DEFECT THAT CAN LEAD TO THE DIFFERENTIAL AND SUSPENSION COMPONENTS IN THE REAR TO COMPLETELY SEPARATE.

The BMW E36 Z3 1996-2002 (I have the 1998 1.9) are prone to having a separation of the Rear subframe from the differential causing the drivetrain to hang off the vehicle and/or rip out of the trunk's weak aluminum sheet subframe. BMW Germany has acknowledged the problem for a few individuals over the past decade and a half and kept it on the low for them to not spread it further. BMW North America fails to acknowledge the design flaw during their manufacturing process in the North American Plant during the late 90s. The Spot Welds' quality is subpar and worrisome as this catastrophic failure of the subframe to driveline structure has various ways of presenting it self which chiefly includes popped spot welds in the truck which comes hand in hand with a cracked differential ear bracket. * To simply understand why this happens: The issue is that the metal of the trunkfloor is too thin and not adequete at holding up to the forces of the differential tugging at it. There have been documented cases of similarly "repaired" Z3's that end up basically pulling out and/or deforming the entire trunkfloor panel. The metal panel the diff crossmember is structurally tied to (and the trunkfloor itself which is above it) is simply too weak for the forces being applied through it. Adding more welds simply changes where the failure occurs - from pulling out spotwelds, to deforming the trunk floor/crossmember itself if there are too many welds for them to be able to be pulled out. There are a few kits going around that other owners have addressed to their vehicles for a few thousand dollars which includes welding and a re-fabrication of the trunk floor's structure to the subframe/chasis. It has two "caps" that sit on the framerails at either side and a "crossmember" piece which is a strong piece of metal that spans between the two frame rails and sits on top of the "caps". When installed, the differential ends up tugging at the crossmember, which then distributes the forces.....

I HAVE A 1998 Z3 M ROADSTER AND THE TRUNK WELDS HOLDING THE SUBFRAME IS FAILING. THIS IS A COMMONLY DOCUMENTED ISSUES. BMW DEALERS ACKNOWLEDGE THE ISSUE BUT BMW NORTH AMERICA WILL NOT FIX IT. THIS IS A WELDING/MANUFACTURING DEFECT THAT CAN LEAD TO THE DIFFERENTIAL AND SUSPENSION COMPONENTS IN THE REAR TO COMPLETELY SEPARATE.

WHILE DRIVING AIR BAG WARNING LIGHT WOULD COME ON. CONSUMER HAS CONTACTED THE DEALER.*AK

THE DRIVER WAS STOPPED AT A LIGHT WHEN THE VEHICLE WAS IMPACTED IN THE FRONT AT 45 MPH. NEITHER OF THE FRONTAL AIR BAG DEPLOYED. THE SEAT BELT ALSO FAILED TO PROPERLY RESTRAIN THE DRIVER. *AK *CB *NLM

THE PLASTIC REAR WINDOW IN THE CONVERTIBLE TOP HAS A DESIGN FLAW. WHEN THE CONVERTIBLE TOP IS LOWERED AND THEN RAISED AGAIN (THE INTENDED NORMAL OPERATION OF THE CONVERTIBLE TOP), IT CAUSES SEVERE CREASING OF THE REAR WINDOW. THIS RESULTS IN THE REAR VIEW OUT THE WINDOW BEING SIGNIFICANTLY DISTORTED AND IMPAIRED, WHICH I THINK IS A SAFETY HAZARD. I HAVE CONTACTED BOTH THE DEALER AND BMW ABOUT THIS. THEY HAVE TOLD ME THAT "THEY ALL DO THIS" AND THAT THERE IS NOTHING THEY CAN DO ABOUT IT. THERE IS NOTHING THE OWNER CAN DO TO REMOVE THE CREASES. THE ONLY RESPONSE THE DEALER HAS PFFERED IS TO HEAT-TREAT THE WINDOW AND MELT AWAY THE CREASES. HOWEVER, THE NEXT TIME THE TOP IS LOWERED AND THEN RAISED AGAIN, THE WINDOW HAS THE SAME DEEP CREASES. THIS CONCERNS ME, BECAUSE THE DISTORTED REAR VIEW IS DISTRACTING AND A SAFETY HAZARD BECAUSE ONE CANNOT SEE CLEARLY TO THE REAR OF THE CAR.

REARVIEW MIRROR CREATES HUGE BLIND SPOT AND IS A POTENTIAL HAZARD.

I HAVE A 1998 Z3 M ROADSTER AND THE TRUNK WELDS HOLDING THE SUBFRAME IS FAILING. THIS IS A COMMONLY DOCUMENTED ISSUES. BMW DEALERS ACKNOWLEDGE THE ISSUE BUT BMW NORTH AMERICA WILL NOT FIX IT. THIS IS A WELDING/MANUFACTURING DEFECT THAT CAN LEAD TO THE DIFFERENTIAL AND SUSPENSION COMPONENTS IN THE REAR TO COMPLETELY SEPARATE.

BMW Z3 IS A PIECE OF CRAP. DEALER NOW THINKS THAT THERE IS UNDERLYING PROBLEM WITH VEHICLE. 3 CD PLAYERS, 2 IGNITION SYSTEMS, 1 FUEL SENSOR, 1 ENGINE THAT WOULDN'T START DUE TO SOMETHING STUCK OPEN AND JUST GENERAL POOR QUALITY. I DO NOT RECOMMEND THIS VEHICLE FOR ANYONE.

AFTER APPROXIMATELY 15 MINUTES OF DRIVING A FIRE ERUPTED FROM UNDER THE HOOD, NO INDICATOR LIGHTS DISPLAYED AND NO ODOR OF RAW FUEL WAS APPARENT. POWER TO THE VEHICLE ULTIMATLEY FAILED AS WELL AS THE BRAKES. WIFE ABLE TO STOP THE VEHICLE USING THE EMERGENCY BRAKES. WITHIN MINUTES THE MOTOR AND ACCOUTERMENTS WERE CHARRED TO A CRISP. THE VEHICLE WAS TOTALED.

BMW Z3 IS A PIECE OF CRAP. DEALER NOW THINKS THAT THERE IS UNDERLYING PROBLEM WITH VEHICLE. 3 CD PLAYERS, 2 IGNITION SYSTEMS, 1 FUEL SENSOR, 1 ENGINE THAT WOULDN'T START DUE TO SOMETHING STUCK OPEN AND JUST GENERAL POOR QUALITY. I DO NOT RECOMMEND THIS VEHICLE FOR ANYONE.

I HAVE HAD THIS VEHICLE SERVICED 4 TIMES ... THEY ARE UNABLE TO FIX THE PROBLEM, I LOSE ALL HEAD LIGHTS AND INSTRUMENT CLUSTER WHEN THIS HAPPENS .. INCLUDING MY TURN SIGNALS..

PASSENGER SEAT BELT FAILED. YH

OWNERS MANUAL STATES WARNING TRIANGLE AND FIRST AID KIT ARE LOCATED ON VEHICLE, THIS IS NOT SO, ONLY OFFERED TO EUROPEAN VEHICLES.

WHILE MAKING A LEFT TURN THE STEERING LOCKED UP, CAUSING VEHICLE TO SPIN OUT OF CONTROL, RESULTING IN A COLLISION. MANUFACTURER HAS INSPECTED THE VEHICLE . THE VEHICLE IS BEING REPAIRED. *AK

BMW Z3 IS A PIECE OF CRAP. DEALER NOW THINKS THAT THERE IS UNDERLYING PROBLEM WITH VEHICLE. 3 CD PLAYERS, 2 IGNITION SYSTEMS, 1 FUEL SENSOR, 1 ENGINE THAT WOULDN'T START DUE TO SOMETHING STUCK OPEN AND JUST GENERAL POOR QUALITY. I DO NOT RECOMMEND THIS VEHICLE FOR ANYONE.

TRANSMISSION POPS OR JUMPS OUT OF FIRST GEAR UPON TAKEOFF. *AK

REAR STABILIZER BAR REPAIRED SEVERAL TIMES WITH THREE REPLACEMENTS. MJS