RoadVitals

1988 Ford B600 Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
Recall campaignsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
3
Newest Jun 27, 1994
Carrying an NHTSA advisoryCampaigns where NHTSA told owners not to drive the vehicle, or to park it outside, until the repair is done.
0
Open investigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0
2 investigations on file

Recall campaigns

3 campaigns cover this model year — what the defect is, what it could cause, and what the remedy is

94V118000

STEERING:RACK AND PINION

Jun 27, 1994
12,700 units potentially affected
The defect: THE STEERING GEARS HAVE AN IMPROPERLY MACHINED SNAP RING GROOVE. THIS CAN CAUSE A FRACTURE OF THE SNAP RING WITH SUBSEQUENT DAMAGE TO THE RECIRCULATING BALL GUIDE TUBE. ALSO, THE O-RING SEAL IN VEHICLES BUILT AFTER FEBRUARY 1988 DOES NOT MEET SPECIFICATIONS AND IS INADEQUATE, CAUSING INTERIOR LEAKAGE AROUND THE O-RING / GLIDE RING SEAL IN THE STEERING GEAR.
The risk: THE FRACTURE OF THE SNAP RING RESULTS IN INCREASING DETERIORATION OF THE ABILITY TO TURN THE VEHICLE TO THE RIGHT. THE DRIVER WOULD EXPERIENCE INCREASED STEERING EFFORTS OR A "CRUNCHY" FEELING AT THE STEERING WHEEL. THE INADEQUATE O-RING SEAL CAUSES MOMENTARY REDUCTIONS IN POWER STEERING ASSIST AT LOW SPEED AND CERTAIN LEFT TURN MANEUVERS. BOTH CONDITIONS RESULT IN DECREASED STEERING ABILITY.
The remedy: DEALERS WILL REBUILD THE STEERING GEAR. IF A BROKEN SNAP RING IS FOUND DURING REBUILDING, THE STEERING GEAR WILL BE REPLACED WITH A REMANUFACTURED UNIT.
FORD MOTOR COMPANYView on NHTSA.gov
94V056000

ELECTRICAL SYSTEM:12V/24V/48V BATTERY

Mar 26, 1994
3,660 units potentially affected
The defect: SYSTEM: ELECTRICAL SYSTEM; BATTERY. VEHICLE DESCRIPTION: MEDIUM DUTY SCHOOL BUS CHASSIS EQUIPPED WITH HYDRAULIC BRAKES, TILT HOODS, 5.9L, 6.6L OR 7.6L DIESEL ENGINES OR 6.1L OR 7.0L GASOLINE ENGINES AND ORIGINALLY SOLD OR CURRENTLY REGISTERED IN CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA ,RHODE ISLAND, VERMONT, AND WISCONSIN. THE BATTERY POWER JUNCTION BLOCK MOUNTED ON THE RIGHT FENDER APRON, WHICH SERVES AS AN ELECTRICAL CONNECTION POINT FOR SEVERAL ENGINE COMPARTMENT SYSTEMS, IS SUSCEPTIBLE TO ROAD SPLASH. THE TERMINALS AT THE JUNCTION BLOCK CAN EXPERIENCE CORROSION AND CAN FRACTURE, CAUSING LOSS OF ELECTRICAL POWER AND ENGINE SHUTDOWN.
The risk: ENGINE SHUTDOWN, LOSS OF POWER STEERING ASSIST, OR LOSS OF HYDRAULIC BRAKE BOOST CAN OCCUR WHICH MAY RESULT IN LOSS OF VEHICLE CONTROL AND AN ACCIDENT.
The remedy: DEALERS WILL REPLACE THE JUNCTION BOX, MAIN POWER TERMINAL THE STARTER OR STARTER RELAY AND TERMINALS AT THE EXISTING JUNCTION BLOCK. THE WIRING OF THE HYDRAULIC BRAKE CIRCUIT WILL ALSO BE MODIFIED BY BYPASSING THE JUNCTION BLOCK. THE NEW TERMINALS WILL BE MADE FROM AN ALLOY MATERIAL MORE RESISTANT TO SALT CORROSION.
FORD MOTOR COMPANYView on NHTSA.gov
91V126000

STEERING:GEAR BOX (OTHER THAN RACK AND PINION)

Jul 16, 1991
3,000 units potentially affected
The defect: BECAUSE OF A MACHINING INCONSISTENCY, THERE IS A HIGH PISTON-TO-BALL CONTACT ANGLE IN THE STEERING GEAR WORM DRIVE. THIS CONTACT CAUSES THE BALLS TO TRY TO ROTATE ON TWO DIFFERENT ROLLING RADII AT TWO DIFFERENT SPEEDS, CAUSING THE BALL TO DAMAGE THE CONTACT SURFACES OF THE PISTON AND SPINDLE DURING STATIC OR LOW SPEED MANEUVERS INVOKING FULL OR NEAR FULL TURNS.
The risk: STEERING ABILITY DETERIORATES AND EVENTUALLY STEERINGLOCKUP OCCURS DURING THESE LOW SPEED MANEUVERS RESULTING IN LOSS OF STEERINGCONTROL AND AN INCREASED RISK OF VEHICLE ACCIDENT.
The remedy: REPLACE BENDIX C300N STEERING GEARS WITH NEW GEARS.
FORD MOTOR COMPANYView on NHTSA.gov

What a recall is

Safety recall
A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation
NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Safety investigations

NHTSA inquiries naming this vehicle. An investigation is not a finding of a defect, and it is not a recall.

EA91014ClosedEngineering Analysis

STEERING LOCKUP

Opened Jan 31, 1991
Closed Aug 27, 1991

There is no summary currently available

STEERINGLed to recall 91V126000
PE91002ClosedPreliminary Evaluation

STEERING LOCKUP

Opened Oct 3, 1990
Closed Jan 31, 1991

There is no summary currently available

STEERING

Elsewhere on this vehicle

Data sources