2021 Ford Bronco Driver assistance Problems

I was driving in the northbound left hand lane on creasy lane in Lafayette, Indiana, approaching Rome Drive. A driver from a side street took an illegal left hand turn to head towards the northbound lanes of creasy lane, I was traveling over 30 mph, maybe 40 at the time of the collision. I was unable to see the other driver until it was too late as they passed by drivers turning from the right hand lane onto the side road they had been at. My airbags did not deploy during the collision, nor did my pre collision assist alert nor did my brake system engage. I suffered extensive front end damage at the time of the incident. There was a previous recall for my airbags in this vehicle, as well as notifications in 2024 that my collision systems had been disengage during warranty work.

NHTSA ID

11746859

Incident

Jun 25, 2026

I was driving on the highway with standard cruise control (I don't have adaptive cruise) and I went to press the brakes and the brake pedal was SUPER stiff and I had to press unreasonably hard to disengage the cruise control and slow down. When the pedal finally gave, I ended up slamming on the bakes so much that my passenger was startled and we both lurched forward due to our momentum. Afterwards, my brake light light came on, on the dashboard. I went to AutoZone to get a reading and it said it was the brake assist vacuum or something like that. This could have caused a very bad accident in too different ways. One, if I didn't stop in time due to the delayed braking from the stiff pedal or getting rear ended due to inadvertently slamming on the brakes at highway speed.

NHTSA ID

11744011

Incident

May 1, 2026

The digital gauge cluster where it shows sensitive information is a blacked out screen. I took it an automotive shop to investigate the issue. They ran a diagnositic and confirmed the screen is receiving power, fuses are good, but the screen is not powering up. I cannot view the digital speed, fuel gauge, mileage, access GOAT modes, view tire pressure, view oil life, and other critical data, etc. This first occured a few months ago and would randomly turn back on, but not the screen is black more than it is on. Luckily I am able to track the fuel gauge (miles to empty) on the infotainment screen.

NHTSA ID

11733378

Incident

Jan 27, 2026

3 separate safety-related components have failed on my 2021 Ford Bronco, all of which correspond to open federal safety recalls that remain unremedied: 1. Infotainment/APIM Module & Backup Camera System (Recall Campaign 26V124): my infotainment screen fails to turn on, particularly in high-temperature conditions. When this occurs, the rearview/backup camera is completely non-functional. The vehicle displays no image when in reverse gear, eliminating all camera-assisted visibility behind the vehicle. This directly matches the conditions described in Recall 26V124, issued March 4, 2026. No remedy has been provided. 2. Digital Instrument Cluster / Dashboard: my digital dashboard intermittently fails to illuminate at vehicle startup. This occurs randomly and without warning. When it fails, the driver cannot see critical safety information including current speed, fuel level, engine temperature, or any warning indicators. Video documentation of this failure exists. This component is available for inspection upon request. 3. Low Pressure Fuel Pump (Recall Campaign 25V455): my vehicle has stalled on multiple occasions while in motion. During stall events, all dashboard warning lights illuminate simultaneously. This is consistent with the fuel delivery failure described in Recall 25V455, issued July 8, 2025, which states the fuel pump can fail causing loss of fuel pressure and an engine stall while driving. No remedy has been provided since the recall was issued in July 2025 (~9 months ago). All components are available for inspection upon request. However, the authorized Ford dealership in the area has refused to accept the vehicle for service or inspection, citing parts unavailability. Engine stall while in motion. my vehicle has stalled multiple times while being driven. The driver works as a real estate agent and regularly transports clients in this vehicle. The engine has stalled with passengers present. A sudden engine stall while driving results in immediat

NHTSA ID

11731872

Incident

Nov 19, 2025

My BLIS module on the passenger side does not work and I have a constant warning light displayed that there is a system malfunction. Under further investigation, this is a KNOWN design issue caused by the rear wiring harness that contains the BLIS sensor rubbing against components in the rear bumper. My vehicle has 31000 miles on it and is now out of warranty. Ford dealers are aware of this issue but claim it is not a recall and not under warranty. This is a safety issue.

NHTSA ID

11724615

Incident

Mar 13, 2026

The wiring harness is rubbing against the bumper, causing it to wear and eventually cut through. This causes an error to my BSM/Cross Traffic alert. I have an extended warranty, but it doesn't cover it. This is a problem I have seen on the Bronco6G forums.

NHTSA ID

11715858

Incident

Feb 5, 2026

While driving I lost most/all ADAS system. I received several alerts that kept repopulating. No Cross Traffic working No Blind Sport working No Cruise Control No Forward Collision working No Lane Departure working I took the rear assembly by the taillight and rear bumper. The wires and electrical components are corroded. Koons Ford Annapolis Maryland is requiring $1520 parts and labor.. This is a major safety problem as it was not designed correctly. Many Bronco Owners are going through this..

NHTSA ID

11712374

Incident

Dec 30, 2025

I received an alert on the dash stating there was an issue with the blind spot monitoring/rear cross traffic system. It was erroring off and on for that entire drive. When I got home, I googled the issue and it appears it's a known issue with '21 and some early '22 broncos where they factory installed the blind spot module wiring harness too close to the rear bumper. Over time, the wires rub and eventually rub bare and corrode or short out. I went out to take a look and sure enough, I had rubbed through on the driver side (photo) and the passenger side was nearly rubbed through. I have an extended warranty and it's at the dealership today. This is a manufacturing defect and should be covered (even if out of warranty) in my opinion. We will see what kind of story the dealer can come up with to wiggle out of it being covered under warranty.

NHTSA ID

11712311

Incident

Jan 16, 2026

Bronco wire corrosion cross traffic refers to a known issue where wiring under the rear bumper, often for the blind spot/cross-traffic sensors, chafes, frays, and corrodes, causing system faults and failures, sometimes due to design flaws or environmental exposure to salt, requiring inspection and repair of the harness. This problem triggers error messages like "Cross Traffic System/Blind Spot System Fault" in the instrument cluster, impacting safety features, with potential fixes involving harness repair, protective sheathing, or sensor replacement. My car’s wiring was corroded due to this flaw and required a repair exceeding $1,000.

NHTSA ID

11711629

Incident

Dec 17, 2025

Location of wiring from the factory for Blind Spot Warning and Cross Traffic Alert systems is not protected. The wiring has frayed and broken due to the wiring being unprotected, loose and rubbing on the rear bumper, causing the systems to not function. This is a blatant design defect from the factory, causing two safety systems to fail. Reporting now as, to the best of my knowledge, the manufacturer has not issued a TSB or recall and dealerships have acknowledged the issue.

NHTSA ID

11706454

Incident

May 1, 2025

I was driving on the highway at a speed of approximately 70 miles per hour when the Bronco driver screen gave multiple warning notices and at the same time, the accelerator would not react. Steering power was fine. I was in the second from far left lane on a six lane highway and losing speed quickly. I was able to move to the right and drift to the side of the road without incident. Once stopped, I turned the ignition off and waited a few seconds and then turned it back on again. The error messages all cleared and the Bronco accelerator reacted appropriately. I drove it straight to the dealership for inspection. They found the 210 connector was not making a good connection. They cleaned it and added electric grease and reconnected. Everything cleared and the connection was deemed good. I have not worked in the Bronco engine compartment or had work done that would have resulted in loosening the 210 connector. My understanding from the shop is that corrosion caused this connector to loosen.

NHTSA ID

11698141

Incident

Oct 9, 2025

rear view camera display when vehicle is in reverse will intermittently turn blue or black which renders the rear view camera useless. and at times will state camera unavailable. vehicle is a 2021 ford bronco built on june 15, 2021 at ford Michigan build plant. i have contacted ford related to this concern as i believe that the vehicle should fall under recall 23s48 for rear camera replacement, and 25s49 for module updates related to rear camera display. the vehicle year, build date, assembly plant and symptoms all fit within the parameters of recall. note that i also have a 2022 bronco that these recalls are active on for the same concerns, the concern happens 7-8 times a week for the last 4-5 months. dealership has contacted ford sssc team about getting recalls activated on this vehicle and they are given the most basic responses stating that this vehicle is not included due to "certain model year vehicles" even though the vehicle is clearly within the model years outlined in both recalls. the rear view camera intermittently not working is a safety issue as it can stop working at any time when you would be using it to reverse. thank you for your time and consideration when investigating this concen.

NHTSA ID

11688956

Incident

Sep 2, 2025

I have been getting a message that my blind spot and cross traffic alert deactivated because trailer is attached. I have never had a trailer attached but do have a trailer hitch- the dealer said Ford refuses to pay to have it fixed because the bumper to bumper warranty is out. the car has been garaged and has only 9,000 miles on it. This is a safety issue that I think they should cover as I have no blind spot or cross traffic warnings.

NHTSA ID

11683687

Incident

Aug 16, 2025

Cross traffic and blind spot monitoring/alert failed. Electrical wiring failed due to rubbing on the rear bumper causing failure of blind spot alert and cross traffic alert systems. Reliance on these systems is critical to safe operation of the vehicle.

NHTSA ID

11676692

Incident

Jul 28, 2025

The contact owns a 2021 Ford Bronco. The contact had received notifications of NHTSA Campaign Numbers: 24V635000 (Engine and Engine Cooling), 25V025000 (Suspension), 25V315000 (Back Over Prevention) and 25V455000 (Fuel System, Gasoline); however, the parts to do the recall repairs were not yet available. The local dealer was made aware of the issue and confirmed that parts for all four recalls were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the rear camera intermittently displayed a distorted image while the vehicle was in reverse. The manufacturer was made aware of the issue. The failure mileage was unknown. VIN tool confirms parts not available for NHTSA Campaign Numbers: 25V025000, 25V315000, and 25V455000. Parts distribution disconnect for NHTSA Campaign Number: 24V635000.

NHTSA ID

11673354

Incident

Apr 1, 2025

I had the cross-traffic sensor and blind spot detection sensors changed about a year after I bought my Bronco and the tech told me where the wires are housed it is wide open to the elements which cause the wires to fail. This was fixed under warranty and now 2 years later I have the same issue, and Ford will not fix since I am out of warranty. This is not only a design flaw but also a safety issue for someone who relies on those sensors to work.

NHTSA ID

11669268

Incident

Jan 22, 2025

I am receiving Blind spot and cross traffic failure alerts in my vehicle dashboard indicating these systems are not working properly. This is a known issue by many Bronco owners. I believe its due to a bad installation design where the wires naturally rub up against the bumper and with weather exposure they are failing.

NHTSA ID

11661138

Incident

Feb 1, 2025

Our family was traveling from Lake George New York to Boston MA on Wednesday [XXX]. As we passed another vehicle in the far left lane on [XXX] the vehicle bounced and we lost control of the backend of the vehicle and it "fish tailed" across the highway nearly causing a collision at 65 miles per hour. The anti-lock breaks were activated and we nearly collided with several cars but managed to pull into the emergency lane. The vehicle was not drivable after this incident because any pothole or bump on the highway, at speeds over 50 MPH, made the rear of the vehicle very unstable. It will skid and sway. Our vehicle is now undrivable and Ford says the only available solution is a "buy back" program and a solution will not be available until Q3 of 2025. This leaves us with a 4 year old vehicle with only 24k miles undrivable. This is not acceptable. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11648104

Incident

Mar 11, 2025

The contact owns a 2021 Ford Bronco. The contact stated that while in reverse on several occasions, the back-over prevention camera failed to work as intended. The contact stated that on one occasion while in drive, the back-over prevention camera was displayed inadvertently. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 6,000. The VIN was not available.

NHTSA ID

11639094

Incident

Jan 20, 2025

Mileage

6,000 mi

The vehicle will throw a warning saying the cross trafic collision is in operable. A ford tech looked at it and said a wiring harness is chaffed causing blind spot monitioring and cross traffic collision systems to not work. Cost of the part only is $700, not including labor. this is a very serious fault, which could result in injury and fatalitys

NHTSA ID

11632944

Incident

Jun 1, 2024

The contact owns a 2021 Ford Bronco. The contact received notification of NHTSA Campaign Number: 23V165000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. Parts distribution disconnect.

NHTSA ID

11610145

Incident

May 10, 2023

The contact owns a 2021 Ford Bronco. The contact received notification of NHTSA Campaign Number: 23V165000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer and two unknown dealers were contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and referred the contact to the NHTSA hotline for assistance. The contact had not experienced a failure. Parts distribution disconnect.

NHTSA ID

11570118

Incident

Feb 5, 2024

The contact owns a 2021 Ford Bronco. The contact received notification of NHTSA Campaign Number: 23V165000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was contacted it was confirmed that the software to perform the update was not available. The manufacturer was made aware of the issue, and it was confirmed that the parts to perform the software updates were not available. The contact had not experienced a failure. Parts distribution disconnect.

NHTSA ID

11567524

Incident

May 10, 2023

The contact owns a 2021 Ford Bronco. The contact received notification of NHTSA Campaign Number: 23V598000 (Back Over Prevention) however the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.

NHTSA ID

11557072

Incident

Nov 27, 2023

In late March 2023, the touchscreen on my Bronco went dead, along with the USB ports in the console below. With the dead screen, I have no back up camera, which is a huge safety concern. Also, all other features managed by the touch screen are gone (no radio, no navigation, no hands free phone usage, etc.). I have been to the dealer twice, and they said we just have to wait for Ford engineers to send a patch to the SYNC system, because they think it has interfered with the APIM module. This may or may not be related to the open recall 22c27, because that is not the same issue as mine. But Ford just is telling me to wait for that recall to be completed, but for four months and counting they have not provided a patch for the 8-inch screen model that I have. I have been given no other options except potential buy back of the vehicle.

NHTSA ID

11532834

Incident

Mar 20, 2023