2022 Ford Bronco Problems

The windshield washer fluid reservoir cracked along its seam and drains completely after a few hours. This was not due to an accident and I have not done off-roading. I live in a snowy environment and not having an operating windshield washer is a MAJOR safety hazard as road salt quickly builds up on the windshield dramatically reducing forward visibility. It also affects the rear window washer, but that’s not as troubling an issue. The defective reservoir is available for inspection. My local mechanic confirmed that the reservoir is cracked. My photo shows the fluid leaking onto the ground. The component has not been inspected by the manufacturer, police or insurance, but has been inspected by a mechanic at my local Chevron station. A “washer fluid low” warning and idiot light appears after the reservoir drains, goes off when fluid is added, and goes on again when the fluid drains out again. I have ordered a replacement reservoir from Ford (which has been revised from the original) plus two required hoses for $477.28 (without installation). An internet search suggests this is a common problem for my vehicle.

The rear hardtop panel on my 2022 Ford Bronco has developed serious cracking and surface separation after only three years of light, garage-kept use. The fiberglass is fracturing near the seams, exposing the underlying material. Water is now visibly collecting in the openings, which will lead to internal moisture intrusion, mold, and eventually corrosion of structural components underneath the hardtop mounting area. This poses a serious long-term safety concern, especially in the event of rear impacts or rollover situations. A Ford dealer inspected the issue and submitted a warranty claim, which was denied. The Ford representative acknowledged the damage but said they could not act without a recall or broader investigation. No warning lights or messages appeared; the issue is external and has progressed gradually. The damage began well before my bumper-to-bumper coverage expired, but has recently worsened. Ford’s own General Service Bulletin GSB 23-7174 lists rear hardtop panel cracking and edge delamination as warrantable conditions. My panel clearly fits those descriptions. Still, I was quoted nearly $10,000 for a full replacement, which is unreasonable. This is not an isolated case. Many 2021–2022 Bronco owners have posted identical problems online. Ford is clearly aware of this issue—which is why they issued that bulletin—but is denying claims unless pressured through complaints. I believe this is a materials or manufacturing defect and ask NHTSA to investigate this clear and ongoing failure.

The contact owns a 2022 Ford Bronco. The contact stated that while leaving the residence, the vehicle stalled on the highway. The driver was able to avoid a crash with a tractor-trailer. The check engine warning light illuminated intermittently, and a “Service Vehicle Soon” message was displayed. Additionally, there was a tool symbol displayed on the instrument panel. The vehicle was towed to a local dealer, and the contact was informed that the part needed to perform the recall repair of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline); was not yet available. The manufacturer was not contacted. The failure mileage was approximately 75,000.

The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline); however, the part to do the recall repair was not yet available. The local dealer was contacted and confirmed the part to do the recall repair was not available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure.

The contact owns a 2022 Ford Bronco. The contact stated that while leaving the residence, the vehicle stalled on the highway. The driver was able to avoid a crash with a tractor-trailer. The check engine warning light illuminated intermittently, and a “Service Vehicle Soon” message was displayed. Additionally, there was a tool symbol displayed on the instrument panel. The vehicle was towed to a local dealer, and the contact was informed that the part needed to perform the recall repair of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline); was not yet available. The manufacturer was not contacted. The failure mileage was approximately 75,000.

The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 26V468000 (Engine, Electrical System); however, the part to do the recall repair was not yet available. The contact stated that while his wife was driving 70 MPH uphill, the vehicle lost drive power. Several unknown warning lights were illuminated. The driver was able to pull over to the side of the road. The vehicle was towed to the dealer, where it was diagnosed and determined that the main wiring harness had dislodged, sat across the exhaust, and was burned. The dealer determined that the main wiring harness needed to be replaced, which required the temporary removal of several components. The contact was provided a repair estimate and was advised that the failure was not covered under the recall and that the vehicle was out of warranty. The vehicle was not repaired. The contact obtained a rental vehicle out-of-pocket. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure and informed the contact that partial assistance might be provided. The failure mileage was approximately 60,908.

I drive a Standard ‘22 Bronco. Only E-brake works for parking brake when in parking lots and such. My Bronco rolls into oncoming traffic and pedestrians when the e-brake releases. I am former Homeland Security and this unacceptable, as this if my 10th issue with the Ford Bronco! Safety First!

There has been an SSM release by Ford (SSM 51415) acknowledging that 2021-2022 Bronco vehicles flat towed in neutral may experience inconsistent or unintended ABS (anti-lock brake) module activation while being towed. The ABS module exits sleep mode unexpectedly due to road vibration input during towing, which can cause brake drag or lockup while the vehicle is being flat towed behind a motorhome. This is a safety concern as unexpected braking of the towed vehicle can affect the towing vehicle's stability and control at highway speeds. The vehicle is being operated exactly as documented in the Ford owner's manual, which explicitly supports neutral flat towing. Ford has developed a software update to address this defect but is declining to cover it under warranty or goodwill, instead classifying it as non-covered maintenance. The issue has been confirmed by an authorized Ford dealership who identified SSM 51415 as applicable. A community workaround requiring removal of fuses 28 and 29 to disable the ABS pump has emerged among owners, indicating this is a widespread known issue affecting safety during a manufacturer-approved towing method. Ford should issue a TSB or recall and cover the software correction at no cost to owners.

The contact owns a 2022 FORD BRONCO. The contact became aware that the VIN was included in NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline) through a VIN search; however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair.  Additionally, the contact stated that the rearview and front view cameras were intermittently inoperable. The contact related the failure to NHTSA Campaign Number: 26V124000 (Back Over Prevention). The dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the issue. The failure mileage was approximately 8,600.

The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V312000( BACK OVER PREVENTION) However, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure

The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 26V468000 (Engine, Electrical System); however, the part to do the recall repair was not yet available. The contact stated that while his wife was driving 70 MPH uphill, the vehicle lost drive power. Several unknown warning lights were illuminated. The driver was able to pull over to the side of the road. The vehicle was towed to the dealer, where it was diagnosed and determined that the main wiring harness had dislodged, sat across the exhaust, and was burned. The dealer determined that the main wiring harness needed to be replaced, which required the temporary removal of several components. The contact was provided a repair estimate and was advised that the failure was not covered under the recall and that the vehicle was out of warranty. The vehicle was not repaired. The contact obtained a rental vehicle out-of-pocket. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure and informed the contact that partial assistance might be provided. The failure mileage was approximately 60,908.

Safety Defect – Inadequate Warning and Insufficient Time to Respond to Alternator/Charging System Failure I am submitting this safety complaint regarding a dangerous condition in my 2022 Ford Bronco involving the charging system and alternator protection behavior. While driving, a warning related to the charging system/battery appeared. The message lacked sufficient clarity and urgency. The time from the warning until the 12-volt battery was fully depleted was extremely short—too brief to safely identify a location and pull completely out of traffic. Once the battery died: • The vehicle could not be placed in neutral, preventing it from being moved out of the travel lane. • There was insufficient power to operate the hazard lights. This occurred on a busy highway, leaving the vehicle disabled in traffic and creating a significant safety risk. I was fortunate it happened in daylight. Had it occurred at night without functioning hazard lights, the likelihood of a catastrophic accident would have been high. This aligns with known alternator/charging system issues on 2021-2022 Broncos addressed in Ford Technical Service Bulletin TSB 23-2238 (superseding TSB 22-2392). The combination of an unclear warning, inadequate response time, loss of neutral capability, and loss of hazard lights presents an unreasonable safety risk. I request that Ford investigate this condition, provide a permanent remedy, and improve the warning strategy so drivers receive clear, timely notice with enough opportunity to reach a safe location.

2022 Ford Bronco 2.7L EcoBoost VIN [XXX] has experienced recurring engine oil pressure failure causing vehicle to enter limp mode limiting speed to 25mph creating an unsafe driving condition. Diagnostic trouble codes P0524 Engine Oil Pressure Too Low and P06DD Engine Oil Pressure Control Stuck Off confirmed. Two failed warranty repair attempts at Lenoir City Ford Lenoir City TN on XXX and XXX. Dealership provided loaner vehicle both times acknowledging vehicle was unsafe to drive. Ford corporate case number XXC is open. Third repair attempt scheduled XXX.” INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The Incident: While operating the vehicle under high load, the driver received an explicit "Service Engine Soon" powertrain malfunction alert stating: "The powertrain control module lost communication with the vehicle active grill shutter module for a period of time." Immediately following this warning, the engine experienced a severe loss of power, followed by loud metallic banging from the engine bay. The vehicle stalled completely and lost all motive power, creating an imminent highway safety hazard.The Physical Damage: Subsequent mechanical teardown by the dealership revealed terminal block destruction, including deep vertical cylinder wall scoring, heavy unburnt liquid gasoline residue in the engine oil pan, and a blown head gasket.Relationship to Active Safety Defect: This catastrophic engine failure mirrors the progressive failure profile of NHTSA Campaign 25V455 / Ford Safety Recall 25S75 (Low-Pressure Fuel Pump Failure). In this EcoBoost architecture, the Active Grill Shutter (AGS) module shares critical voltage paths, grounding blocks, and wiring looms with the engine management and fuel delivery systems. The sudden network communication loss is diagnostic proof of a severe voltage drop or electrical short caused by the high-friction fuel pump degradation detailed in Recall 25S75. This circuit failure instantly starved the engine of fuel under turbo boost, inducing an extreme lean-out condition. The resulting pre-ignition forces violently shattered the internal piston rings (the loud banging), which then gouged the cylinder walls, wiped out compression, fouled the crankcase with fuel residue, and blew the head gasket.Request for Action: Ford's current VIN parameters for Recall 25S75 have not yet captured my specific vehicle despite it matching the exact production window, component setup, and catastrophic failure sequence. I am requesting that the NHTSA log this case as definitive evidence of consequential engine destruction originating from the 25V455 fue

I took my vehicle to the local Ford dealership for the remedy for recall Ford 25S01 on Feb 2, 2026. During the inspection, it was found that the part affected was damaged and the dealership sent photos to Ford. After that, I haven't received any guidance from Ford or the dealership. Since the invoice I received indicated that there was a weld crack in one of the absorbers, I assume that the recall should repair this as a safety concern, but I haven't received any proactive communication from Ford or the dealership. I have contacted the dealership twice since February but I have not received any callback. I am concerned that this is a safety issue and Ford hasn't done anything to correct this since they found out about the issue in February.

I took my 2022 Ford bronco Badlands sasquatch in for recall 25s01 rear shock absorber external reservoir corrosion on 01/15/2026 was notified the next day it was fix when I arrived it was not fix they said parts where on backorder and that Ford has placed the recall campaign on hold. I was advised to take vehicle home and they would call back when they hear back from ford.Both rear shocks have failed and reservoir have fallen off. Vehicle is unsafe to drive due to blown rear shocks vehicle is bouncing and feels like it's all over the place

The contact owns a 2022 Ford Bronco. The contact stated that the vehicle had experienced issues with hardtop roof panels. The hatch was cracked, and the forward removable panel had developed bubbles. The contact stated that the front driver’s side panel was chipped and detaching, and the underside of the roof was visible. The contact associated the failure with NHTSA Campaign Number: 26V299000 (Structure); however, the VIN was not included in the recall. The dealer was contacted regarding the failure, and the vehicle was repaired under warranty. The manufacturer was made aware of the failure and stated that the roof panel was not under warranty. The failure mileage was approximately 19,073.

The hard top is cracking and letting water into the cargo area. It seems to be right outside the parameters for recall number 26S32. Talk to dealer over a month ago and have not heard back yet.

Truck began scrolling warnings that pre-collision braking, hill start assist, forward collision, adaptive cruise control, and more were all not working. Alerts came out of no where while driving on highway and continued every 30 min to hour of drive time. Cruise control was disabled with this failure. Diagnosed with faulty steering-rack. This has been recalled on other 2022 Ford Broncos, but for some reason our was not included in this recall. This lot was clearly impacted as well. The truck is used for daily driving, does not go off-roading and was not involved in any collision or incident that triggered this, simply driving down the highway. Please let Ford know to expand the recall, our car is not safe to drive and is not inoperable unless we pay for the repair or the recall is expanded. Thank you for your assistance!

The steering is unsafe, my neighbor works at a ford dealership and said it’s the rack, which I also read online that it’s become a common problem, the steering has become very stiff. To the point where I have had to slam on the breaks at curves in the road just to be able to turn into the bend, which has almost caused two incidents.

The contact owns a 2022 Ford Bronco. The contact stated that while operating the vehicle, the back over prevention camera malfunctioned. Additionally, the contact reported that the check engine warning light illuminated; however, the fault light was cleared by the dealer during a service visit. The contact received notification of NHTSA Campaign Numbers: 25V455000 (FUEL SYSTEM, GASOLINE), 25V721000 (SEATS), and 26V124000 (BACK OVER PREVENTION); however, the parts to do the recall repairs were not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was 63,000.

The contact owns a 2022 Ford Bronco. The contact stated that while driving at an undisclosed speed, the vehicle lost motive power with several unknown warning lights illuminated. The vehicle was towed to the dealer, where it was diagnosed, and determined that the fuel pump had failed and needed to be replaced. The vehicle was repaired. The contact stated that after the repair, while driving at an undisclosed speed, the vehicle unexpectedly shook and sputtered. There was no warning light illuminated. The contact received notification of NHTSA Campaign Numbers: 25V455000 (Fuel System, Gasoline), 25V721000 (Seats), and 26V124000 (Back Over Prevention); however, the parts to do the recall repairs were not yet available. The dealer was contacted. The vehicle was not diagnosed or repaired. The dealer confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure, and a case was opened. The approximate failure mileage was 35,000.

My 2022 Ford Bronco has two active recalls for low pressure fuel pump failure and front seat height-adjust pivot bolt and link replacement with no available remedies. This vehicle has gone thru numerous recalls which I believe this poses a safety and financial hardship.

The seat belt does not retract. It is loose and does not tighten properly.

When turning right, with the turn signal active, the turn signal will over-correct back to neutral and activate the left turn signal. This happens almost every time a sharp right turn is made, such as leaving a parking lot. The signal stalk must then by manually moved back to neutral. This is repeatable and occurs multiple times a week. This creates risk by presenting a false left turn signal to other drivers. This is a common issue on the Bronco, but Ford Motor Company has not provided a fix, TSB, or Recall.

Driving in wet sticky snow the unheated LED headlamps collect snow quickly and provide almost zero projection of light forward. When driving in areas without overhead lighting at night this becomes a serious safety concern and may lead to a serious accident when drivers cannot see any possible obstructions in the roadway or accurately see the edge of the road surface. Have been unable to demonstrate this flaw to any dealers due to snow being unpredictable and dealerships being closed at night. I do have dash cam video showing the issue that can be provided for review, video uploaded to youtube here [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2022 Ford Bronco. A warning light restraint indicator lamp warning saying airbag system may not deploy properly, vehicle impact sensors affecting airbag, received warning indicator on the instrument panel saying vehicle should not be driven until remedied and should be taken to dealer. The vehicle was taken to the dealer where it was not diagnosed or repaired but the dealer advised does not know how to resolve the issue, The manufacturer was not notified of the issue. The approximate failure mileage was 14,440.

Crack in airbag cover on steering wheel

I own a 2022 Ford Bronco. My vehicle has an electronic brake booster failure that causes multiple warning messages, brake system faults, and loss or reduction of brake assist. When this happens, the vehicle also prevents the 4-wheel drive system from engaging or switching modes. This is especially dangerous during winter conditions. When driving in snow or slippery conditions, I am unable to engage 4WD when it is needed most, while also experiencing brake system warnings. The vehicle becomes difficult to control and does not feel safe to drive. The dealership confirmed this is a known issue affecting multiple Ford Broncos and that the electronic brake booster part is currently back-ordered and unavailable. I was told many vehicles are affected, yet there is no recall for the 2022 model year, even though newer model years have a recall for the same component. This issue creates a serious safety risk due to impaired braking performance and inability to use 4-wheel drive in hazardous conditions. The vehicle had to be parked due to safety concerns. and the he issue happens intermittently, making it unpredictable.

The contact owns a 2022 Ford Bronco. The contact stated that while his wife was driving approximately 55 MPH, the electronic traction control failed causing the vehicle to become unstable and difficult to steer or control. Additionally, the braking system had malfunctioned, and the brake pedal was firm while depressed, and the driver was unable to immediately stop the vehicle. The driver was able to steer the vehicle from the middle lane to the shoulder and used the parking brake to slow the vehicle to an eventual stop. The vehicle was later towed to the local dealer. The cause of the failure was not yet determined. During the failure, the driver’s side rear axle and the rear driver’s side wheel studs and aftermarket lug nuts were damaged and needed to be replaced. The vehicle was repaired. The manufacturer was notified of the failure. The failure mileage was 13,664.

On January 17, 2023, while driving down a commonly driven road (Muldoon) in Anchorage, Alaska at approximately 30 mph, I suddenly heard a large air escaping noise "Psh Psh Psh Psh" and it took me a moment to realize what was happening--the dash indicated the PSI of my rear driver's-side tire was deflating rapidly, to completely flat. Had the vehicle lost control in these snowy conditions, it could have ran into multiple other cars on the road--not ruling out the possibility of a roll-over type accident. When I pulled over into a parking lot, I figured that it was just a flat tire, so I jacked up the vehicle. However, at about the point that the front driver's side tire was leaving the ground, but the rear one wasn't, I determined there must have been an additional issue. I looked behind the tire at the suspension, and it appears that an arm of the suspension had broken off and either destabilized the tire to the point where it lacked a seal around the rim and the air leaked out entirely, or put a hole in the tire. No hole was identifiable, but the tire was so deflated it was hard to tell. When I called the dealership, Kendall Ford of Anchorage, they let me know that they didn't have an appointment until March 2023--at which point I refuted that making me wait 2 months with an undriveable vehicle with under 5,000 miles on it was unacceptable--especially for the price I paid (nearly $70,000). No one has been able to inspect the part yet, but it is clear from photos that the rear suspension on the driver's side does not match the passenger's side rear suspension. There were no warning of failure before this occurred, and the vehicle had been treated very well--it has never been off trail or offroading in the sense that it was in an untraveled area. It has been to archangel pass once, but I would not consider this offroading because the trail is not particularly difficult to pass.

The contact owns a 2022 Ford Bronco. The contact stated while driving approximately 5 MPH and attempting to shift the manual transmission from first to second gear, the transmission failed, and the clutch went to the floorboard. The contact stated no warning light was illuminated. The contact had the vehicle towed to a local dealer where it was diagnosed and determined that the clutch had burned, and the transmission needed to be replaced. The vehicle was not repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 4,500.