STRUCTURE
2017 Ford GT
Recalls, owner-reported complaints, investigations and safety data
Overview
Our database contains no NHTSA owner-reported complaints for the 2017 Ford GT. 2 safety recalls have been issued covering this model year; and 17 manufacturer communications are on file.
Complaints are reports submitted by owners and drivers to NHTSA. They are not verified and do not establish that a defect exists.
Safety recalls
2 campaigns cover this model year
Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.
Check a VIN on NHTSA.govSTRUCTURE
Recent owner complaints
Reports submitted to NHTSA, shown in the owner's own words
No owner complaints recorded for this model year
Either none have been filed with NHTSA, or this vehicle is too new for reports to have accumulated.
Manufacturer communications
A bulletin sent by a manufacturer to its dealers. Not a recall, and repairs are not necessarily free.
BACK OVER PREVENTION: REARVIEW SYSTEM BRAKING; BACK OVER PREVENTION: WARNINGS; LANE DEPARTURE: BLIND SPOT DETECTION
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
POWER TRAIN
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
STRUCTURE
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
ELECTRICAL SYSTEM
Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPassÃÂÃÂÃÂî/LincolnWayÃÂÃÂÃÂî app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
ELECTRICAL SYSTEM; EQUIPMENT
Some 2017-2021 Ford GT vehicles built on or before 22-Sep-2021 may need to have a new battery installed for service. A new design service battery has been released and requires a different battery tray and a different local interconnect network (LIN) connector. This is due to the new battery being smaller and will not properly secure in the original battery tray. The LIN connector socket in the new battery is keyed differently and the original LIN connector will not plug in. The LIN connector will need to be de-pinned, so the new connector shell can be installed. When installing new battery part number: MG7Z-10655-A(USA/MEX), MG7Z-10655-B(CAN), MG7Z-10655-C(GCC) MG7Z-10655-D(EU), the following battery tray and LIN connector must be used: battery tray MG7Z-10732-A, LIN connector shell MG7Z-9A624-A. Refer to Workshop Manual, Section 414-01 for battery tray replacement.
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.
Compare model years
Complaint and recall counts across every year of this model
Higher-selling and older vehicles accumulate more reports. Counts are not failure rates and are not directly comparable between vehicles that sold in very different numbers. Older model years have had longer for reports to accumulate.