RoadVitals

1996 International Harvester 2574 Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
Recall campaignsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
2
Newest Nov 22, 1996
Carrying an NHTSA advisoryCampaigns where NHTSA told owners not to drive the vehicle, or to park it outside, until the repair is done.
0
Open investigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0

Recall campaigns

2 campaigns cover this model year — what the defect is, what it could cause, and what the remedy is

96V233002

SUSPENSION:REAR

Nov 22, 1996
1,133 units potentially affected
The defect: THE DRIVE AXLE HOUSINGS CONSIST OF A PLATE STEEL CENTER SECTION AND TWO FORGED SPINDLES, ONE OF WHICH IS WELDED TO EACH END OF THE CENTER SECTION. EACH SPINDLE CONTAINS A KEYWAY SLOT IN WHICH THE LOCKING TAB FOR THE WHEEL BEARING NUT LOCKING MECHANISM IS INSERTED. THE LENGTH OF THE KEYWAY SLOT MAY NOT BE LONG ENOUGH TO ACCOMMODATE THE TAB CAUSING THE TAB TO BE DEFORMED OR DAMAGED DURING INSTALLATION.
The risk: THIS LOCKING TAB PREVENTS THE WHEEL BEARING NUT FROM LOOSENING DURING VEHICLE OPERATION. IF THIS TAB IS DEFORMED, THE NUT CAN LOOSEN ALLOWING THE WHEEL TO SEPARATE FROM THE AXLE INCREASING THE RISK OF A VEHICLE ACCIDENT.
The remedy: DEALERS WILL REPLACE THE DRIVE AXLE HOUSING NUTS WITH A CONVENTIONAL WHEEL NUT HARDWARE SYSTEM.
INTERNATIONAL TRUCK AND ENGINEView on NHTSA.gov
96V124004

SUSPENSION

Aug 1, 1996
21 units potentially affected
The defect: THE EQUALIZING BEAM SHAFT OF THE TANDEM AXLE SUSPENSION WERE MANUFACTURED FROM AS-ROLLED SAE4140 STEEL RATHER THAN THE SPECIFIED ANNEALED SAE4140. THESE SHAFTS CAN FRACTURE INSIDE THE BEAM AT THE TOE OF THE WELD.
The risk: VEHICLES ARE SUBJECT TO VEHICLE TILT AND POSSIBLE ROLLOVER IN THE EVENT THAT BOTH EQUALIZING BEAMS, ON THE SAME SIDE OF THE VEHICLE, EXPERIENCE A SIMULTANEOUS SHAFT FAILURE. AFFECTED SUSPENSIONS CAN ALSO DROP AND CONTACT THE ROAD SURFACE GENERATING SPARKS WHICH COULD IGNITE FLAMMABLE MATERIAL.
The remedy: OWNER NOTIFICATION IS BEING CONDUCTED BY NEWAY ANCHORLOK. DEALERS WILL INSPECT AND REPLACE ALL SUSPENSION SUSPENSION BEAMS WITH SUSPENSION BEAMS CONTAINING APPROPRIATE SHAFTS.
INTERNATIONAL TRUCK AND ENGINEView on NHTSA.gov

What a recall is

Safety recall
A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation
NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Elsewhere on this vehicle

Data sources