2023 Mercedes-Benz AMG C63 S E

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint SRS indicator light illuminated in the instrument cluster. Electrical fault in the rear airbag/window airbag that may cause a connection between the airbag pins or to the vehicle mass Cause Contact problems that create a short circuit between the pins or to the vehicle ground Remedy Connect and disconnect the affected airbag five times Then the squib must be carefully blown out with dry compressed air. Caution: There must be no mechanical contact! If fault is not rectified: Please measure the internal resistance as described in SI91.00-P-0005A. If the resistor of the airbag is OK, please replace the airbag plug. If the resistance of the airbag is not OK, please replace the airbag. Important: The electrical fault does not affect the functionality of the airbag in the event of an accident. The airbag is functioning as intended.

Complaint The "easy entry and exit feature" function deactivates itself after a brief period. (see attachment) Cause The cause is currently being investigated. Remedy Update the HU7 to the latest software version, then perform a factory reset of the HU7. Steps to perform factory reset: Navigate to Settings > System > Reset > Reset to factory settings and confirm If the problem persists, please record HU7 log and also a trace of the Body CAN (For Star 2 Body Can 1 and for Star 3 Body Can 2) during the symptom and send via a TIPS case to the Body/Chassis/Entertainment inbox. Note: Only collect and submit the log and trace if the symptom can be reliably reproduced.

Complaint The intent of this document is to provide workshops with helpful technical reference language. • Commonly used acronyms in LI's and TIPS cases. • Control unit names, numbers, and how to identify. • Network/wiring architecture groups to baumuster quick reference. • Platform to baumuster quick reference. Cause Information only Remedy Acronyms: • AV = Actual Values • CU = Control Unit • CUL = Control Unit Log • DTC = Diagnostic Trouble Code • E-Stand = Fresh-up head unit boot software (found in head unit control unit log) • FUP = Fresh-up • FW = Firmware • HSVL = High Speed Video Line • HU = Head Unit • HW = Hardware • IPD = Injector Performance Data • ISU = Initial Start Up • LVDS = Low Voltage Differential Signal • NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) • NSFT = Not Safe For Transport • MOPF = Model Facelift (Ex: 167 MOPF) • PiH = Plug-in Hybrid • P3 Hybrid = AMG Plug-in Hybrid with rear drive unit • SA Code = Sonderausstattungscode (Option Code) • SCN = Software Calibration Number • SW = Software • TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) • QT = Quicktest • XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. • Control Unit Name • Control Unit Number • Control Unit Short name • Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 • 117, 156, 246 (MFA) • 166, 176, 221, 242, 246, 292 • 906 Star 2 • 205, 213, 238, 253, 257, 290 (MRA) • 117, 156, 246 (MFA) • 118, 177, 243, 247 (MFA2) • 167, 222, 292, 463, 465 • 907 Star 3 • 294, 295, 296, 297 (EVA2) • 206, 214, 223, 236, 254 (MRA2) • 192 and 232 (MSA) Star 3.5 • 174 • 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": • 205 • 213 • 222 • 238 • 253 • 257 • 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": • 206 • 214 • 223 • 236 • 254 MFA = "Mercedes-Benz Frontwheel Architecture" • 117 • 156 • 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" • 118 • 177 • 243 • 247 EVA1.5 = "Electric Vehicle Architecture" • 243 EVA2 = "Electric Vehicle Architecture - Generation 2" • 294 • 295 • 296 • 297 MSA = "Mercedes-Benz Sport Architecture" • 192 • 232 MMA = "Mercedes-Benz Modular Architecture" • 174 • 178