RoadVitals

2023 Mercedes-Benz AMG EQE 53 4MATIC

Recalls, owner-reported complaints, investigations and safety data

Owner complaintsComplaints are reports submitted to NHTSA by owners and drivers. NHTSA does not verify most reports before publishing them, and a complaint does not establish that a defect exists. Volume is influenced by how many of a vehicle were sold, how long it has been on the road, and how much attention an issue has received.
0
Safety recallsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
2
Latest Aug 20, 2025
InvestigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0
Crash or fire reportedComplaints whose submitter recorded that a crash or a fire occurred. These are the reporter's own answers on the NHTSA form, not verified findings.
0

Overview

Our database contains no NHTSA owner-reported complaints for the 2023 Mercedes-Benz AMG EQE 53 4MATIC. 2 safety recalls have been issued covering this model year; and 25 manufacturer communications are on file.

Complaints are reports submitted by owners and drivers to NHTSA. They are not verified and do not establish that a defect exists.

Safety recalls

2 campaigns cover this model year

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
25V533000

STEERING:CRITICAL FASTENERS

Aug 20, 2025
3,749 units potentially affected
The defect: Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023-2026 EQE and GLC vehicles. Please see the recall report for a complete list of models. The steering coupling bolt may have been improperly tightened, allowing the steering coupling to loosen from the steering rack.
The risk: A loose steering coupling can cause a loss of steering control, increasing the risk of a crash.
The remedy: Dealers will tighten the steering coupling bolts as necessary, free of charge. Owner notification letters were mailed October 6, 2025. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLCView on NHTSA.gov
25V255000

ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS

May 12, 2025
443 units potentially affected
The defect: Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023-2024 C-Class, E-Class, S-Class, SL, GLC, EQE SUV, EQE, EQS SUV, and EQS vehicles that were incorrectly repaired under recall 24V-115. An incorrect fuse box that was not designed for the vehicle may have been installed.
The risk: An incorrect fuse box can result in a sudden loss of drive power or a loss of critical safety functions such as the restraint systems or instrument cluster, increasing the risk of a crash or injury. Additionally, there could be an increased risk of a fire.
The remedy: Dealers will inspect and replace the main fuse boxes, free of charge. Owner notification letters were mailed June 6, 2025. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2025050003/4.
Mercedes-Benz USA, LLCManufacturer number 2025050003/4View on NHTSA.gov

Recent owner complaints

Reports submitted to NHTSA, shown in the owner's own words

No owner complaints recorded for this model year

Either none have been filed with NHTSA, or this vehicle is too new for reports to have accumulated.

Manufacturer communications

A bulletin sent by a manufacturer to its dealers. Not a recall, and repairs are not necessarily free.

LI82.85-P-074735

ELECTRICAL SYSTEM

Complaint When switching the front passenger display on and off, sporadic images may be shown that are similar to stains on the display. This complaint need not be a permanent one, it may disappear again on its own. Cause Implausible video transfer from head unit during start and switch‑off sequence. These images (artifacts) are of a purely cosmetic nature only and they do not impair the function. Remedy Software update of MBUX (A26/17) to software release E316.5 or higher.

LI42.10-P-078779

SERVICE BRAKES

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

LI82.62-P-078631

STRUCTURE:BODY

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

LI82.62-P-078631

STRUCTURE:BODY

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

LI35.30-P-058566

POWER TRAIN

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

LI00.20-P-080703

ELECTRICAL SYSTEM

Complaint Service code B1 displayed in the customer menu does not match the workshop code displayed in the workshop menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.

Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Compare model years

Complaint and recall counts across every year of this model

Mercedes-Benz AMG EQE 53 4MATIC by model year
YearComplaintsRecallsInvestigationsIssue Index
2025010—
2024020—
2023Viewing020—

Higher-selling and older vehicles accumulate more reports. Counts are not failure rates and are not directly comparable between vehicles that sold in very different numbers. Older model years have had longer for reports to accumulate.