2019 Mercedes-Benz AMG GLA45

2019 MERCEDES BENZ GLA 45. CONSUMER WRITES IN REGARDS TO VEHICLE ONLY BEING ABLE TO REVERSE. *LD THE CONSUMER STATED THE DEALER WAS NOTIFIED. THE DEALER STATED THE TRANSMISSION WAS THE CAUSE OF THE FAILURE AND IT WOULD BE WEEKS BEFORE THE VEHICLE COULD BE REPAIRED. *JS

NHTSA ID

11241498

Incident

Jul 20, 2019

Complaint Intermittent shift feel or thud/clunk noise perceived, such as a brief jerk or transmission reaction during certain driving situations. May be most noticeable when transitioning from a coasting condition to accelerator pedal application. May occur in all drive modes. Cause Dual‑clutch transmissions (DCT) inherently exhibit more dynamic shifting behavior compared to other types of transmissions. This is due to the use of physical clutches for starting and gear changes. In certain situations, dynamic driving behavior can lead to a slight jerk sensation which is a normal technical characteristic of the transmission. A typical example is a "Change of Mind" situation: • The customer is coasting towards a red traffic light. • The traffic light turns green while the vehicle is still coasting. • The customer then presses the accelerator pedal. In these situations, a slight jerk may occur briefly because the transmission must quickly engage the appropriate gear and control the clutches accordingly. Since shift forks are responsible for engaging the gears during shifting, a slight shifting noise may also be noticeable. Please note driving programs S, S+, and M are designed to provide sportier vehicle behavior and are not optimized primarily for maximum comfort, so this operation may be more audible. Remedy Verify the customer's concern and confirm proper transmission operation. If no faults or abnormal operating conditions are identified by IPR (Intelligent Predictive Repair), no hardware replacement is necessary. Inform the customer that the transmission has been designed to provide direct gear engagement and responsive vehicle performance. Under certain operating conditions, brief shift sensations may be perceptible and are consistent with the operating characteristics of the dual‑clutch transmission

Dear Mercedes-Benz Owner: In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage Detection ("DMTL") on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership. Why the Warranty extension? On certain Model Year 2018 - 2024 A / C / CLA / CLS / E / G / GLA / GLB / GLC / GLE / GLS / GT / S / SL Mercedes-Benz vehicles, under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code ("DTC") entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp ("MIL"). Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. • If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be covered under this extended warranty and performed at no cost to you. • This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint A popup is seen on the HU with the message "data connection temporarily not available". Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.Navigation 7.iHeartRadio 8.Traffic Cams Cause MB Apps is sundowned for all vehicles with NTG4.5 and NTG5 Head Unit Variant. Remedy No support available for NTG4.5 and NTG5 Head Unit Variants for MB App related topics. Note: Please do not create TIPS. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304