2021 Mercedes-Benz AMG S63

Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the on‑board electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) • It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause • In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. • There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10‑P‑1127WT). Note: An adequate voltage from the on‑board electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the on‑board electrical system battery. ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 2. Connect diagnostic system (see AD00.00‑P‑2000‑06FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view → Drive systems → N127 ‑ "Drivetrain" control unit (CPC) ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 4. Update software for control unit N127 (CPC) (see AR54.21‑P‑0014‑01Y). Info: To do so, select the following menu items: Adaptations → Control unit update → Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 5. Disconnect diagnostic device from vehicle (see AD00.00‑P‑2000‑06FR). ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 6. Disconnect charger from vehicle (see AR54.10‑P‑1127WT).

Complaint Customer states check engine light ON and potentially reduced power output. The following DTC's may be current and/or stored in the ME control unit (N3/10): • P210185 ‑ The throttle valve actuator has a malfunction. There is a signal above the permissible limit value. • P213500 ‑ The values from the position sensors of the throttle valve are implausible relative to each other • P213600 ‑ The values from position sensors "A/C" of the throttle valve are implausible relative to each other • P210B85 ‑ The throttle valve actuator 2 has a malfunction. There is a signal above the permissible limit value. • P2AD300 ‑ The values from the position sensors "A/G" of the throttle valve are implausible relative to each other • P2AD200 ‑ The values from position sensors "B/G" of the throttle valve are implausible relative to each other. NOTE: The faults may also be present in the ME control unit "faults without status filter" Cause Increased electrical resistance between the pins for left and right throttle actuators (M16/60 and M16/61) and the sockets on the engine wiring harness connector. Remedy Replace the sockets in the engine wiring harness connector at both the left and right throttle actuator with the following parts: Silver Plated Sockets 8x A 003 982 70 26 (according to wiring diagram 0.5 mm) 4x A 003 982 73 26 (according to wiring diagram 0.75 mm) ELA Seals 12x A 001 545 50 80

Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic /9G‑TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G‑TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on‑going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: ‑ NAG3 Classic (automatic transmission 725.0) ‑ NAG3 Classic ‑ AMG sport model (AMG 43 and AMG 53 with converter, automatic transmission 725.0) ‑ NAG3 Classic ‑ Hybrid (automatic transmission 725.0) ‑ NAG3 Classic ‑ AMG 63 (automatic transmission 725.0) ‑ NAG3 MOPF ISG2 (automatic transmission 725.1) ‑ NAG3 MOPF Hybrid (automatic transmission 725.1) ‑ NAG3 MOPF AMG sport model (AMG 53/AMG 53e with ISG48V2 & converter /hybrid, automatic transmission 725.1) ‑ NAG3 MOPF AMG 43/63 with engine 139/177 (automatic transmission 725.1) Steps for the Service Advisor: Important: The more information and detail that can be given to the workshop about the complaint, then the more effective the subsequent diagnosis with IPR can be. To this end, a detailed service reception questionnaire has been provided to help the Service Advisor ask the right questions about the complaint. ‑ Ask precise details about the customer complaint and the conditions and context. ‑ Fill out the service reception questionnaire (please see WIS document: OF27.00‑P‑3000‑05A) for customer complaints in detail and forward it to the workshop. Operation steps for the workshop employee: 1. Perform quick test 2. Access the transmission control unit via XENTRY Diagnosis 3. Select "A customer complaint has been received" and carry out all subsequent operation steps (IPR diagnosis path). 4. The IPR repair instructions are displayed, Carry out the IPR repair instructions without performing any further diagnostic or repair steps. ‑ Important: The IPR repair instructions are binding and must be carried out. Differing repairs are possible; such repairs must be documented in XENTRY in free text. Please observe the information regarding the IPR diagnosis process in XENTRY. Conventional diagnosis and subsequent appropriate repairs are only permitted if IPR does not specify any repair instructions. Invoicing for the guided IPR steps: Operation item 27‑0640 and 0.1 hours Notice regarding warranty: The use of IPR in association with warranty claims is mandatory! If the IPR repair instructions are disregarded without justification, the warranty claims may be rejected and/or are subject to debit. IPR will provide a measure to repair the vehicle based on various data sources (EEPROM, fault codes, etc). Please consider the vehicle maintenance record of the vehicle. For warranty and goodwill repairs, the transmission ECU test log and/or IPR test result must be uploaded into Paperless XENTRY Diagnosis (pXD) . If repair is being determined based of oil pan condition pictures of oil pan MUST be provided to warranty as justification. ·Tamper‑proof documentation: The IPR repair instructions are stored in the control unit log. Please file this document in a tamperproof manner ‑ either in digital form or as a hard‑copy printout and also enclose a printout with the damaged part. In this regard, please comply with the country‑specific warranty requirements of the MPC/general distributor.

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint Only vehicles with a variable transfer case are affected. This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 ‑ All‑wheel drive (ARS) N127 ‑ 'Drivetrain' (PTCU) control unit Y3/8 ‑ Transmission control for 9‑gear transmission (VGS) N3/10 ‑ Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications ‑ Collect an oil sample of the original fluid 5. Complete all transfer case Tech‑in processes located under VG Control Unit > Adaptations ‑ Resetting the oil service data ‑ Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature (>60C ) 6. Operate vehicle in full circle with steering at full lock ‑ 5x to the left ‑ 5x to the right Return the vehicle to the client and request they drive the vehicle for at least 200 miles and return if the concern is not resolved. The extended drive will ensure the clutches are properly conditioned with the new oil and should resolve the concern. If this LI has already been applied to the vehicle, please submit a TIPS case to the Powertrain inbox with the following information: ‑ Initial quick test with fault freeze frame data ‑ Initial transmission EEPROM data ‑ VGS and Transfer Case Control Unit Log (N45 or N15/7) ‑ Special Acquisition Data .txt file (Transfer Case Control Unit > Special Procedures > Procedures for support queries to market support > Special Data Acquisition) ‑ Photo of the original oil condition ‑ What color was the fluid drained from the transfer case before the oil change? ‑ Was an oil sample collected, and can you provide a photo of the original fluid? ‑ What color and part number fluid was used during the oil change? ‑ How far was the vehicle driven after?