2021 Mercedes-Benz C 300 4MATIC

Driving and something came from underneath the vehicle and cause me to swerve in all the airbags deployed

NHTSA ID

11704073

Incident

Dec 4, 2025

This NCU replaces the prior NCU issued on May 15, 2025, and contains additional MY 2023 and MY 2024 vehicles which are highlighted below. In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (“MBUSA”) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (“MY”) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: •Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (‘MIL’).

Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz, has determined that on certain MY 2019-2021 C-Class, G-Class, GLC, GT, S-Class (205, 463, 253, 190 & 222 platforms) vehicles, the engine control unit software does not correspond to current production specifications. It is therefore possible that on-board diagnostics and/or exhaust gas emissions requirements may not be fulfilled.

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 9, 2026. After July 9th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

Complaint Service code B1 displayed in the customer menu does not match the workshop code displayed in the workshop menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.

Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"