2008 Mercedes-Benz CL550

The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ

The contact owns a 2008 Mercedes-Benz CL550. The contact stated while the vehicle was parked, as she attempted to buckle the driver's seat belt, the belt was not able to be locked into the buckle. The contact attempted several times to latch the seat belt however, the contact stated that it felt like there was an obstruction in the buckle. The contact checked but saw no blockage. The contact stated that the seat belt warning light was not illuminated while seated in the driver seat with the vehicle turned on. The contact was unable to latch the seat belt. The contact had the vehicle towed to a local dealer, where it was diagnosed and determined that the seat belt buckle and wiring harness needed to be replaced. The vehicle had not been repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 68,000.

NHTSA ID

11520425

Incident

Apr 28, 2023

Mileage

68,000 mi

TL* THE CONTACT OWNS A 2008 MERCEDES-BENZ CL550. THE CONTACT STATED THAT WHILE MAKING A U-TURN GOING 5 MPH, THE VEHICLE JERKED AND FAILED TO ACCELERATE ONCE THE ACCELERATOR PEDAL WAS DEPRESSED. THE ABS WARNING LIGHT ILLUMINATED. THE CONTACT PULLED OVER, TURNED OFF AND RESTARTED THE VEHICLE AND THE VEHICLE OPERATED AS DESIGNED. THE VEHICLE WAS TOWED TO MERCEDES-BENZ OF PEMBROKE PINES (14199 PINES BOULEVARD, PEMBROKE PINES, FL 33027, (954) 644-5035) TO BE DIAGNOSED. THE MECHANIC DETERMINED THAT THE TRANSMISSION FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE FAILURE PERSISTED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE CONTACT WAS INFORMED THAT THE VIN WAS NOT UNDER RECALL. THE FAILURE MILEAGE WAS APPROXIMATELY 112,000. THE VIN WAS NOT AVAILABLE.

NHTSA ID

11373433

Incident

Nov 2, 2020

Mileage

112,000 mi

TL* THE CONTACT OWNS A 2008 MERCEDES-BENZ CL550. WHILE DRIVING APPROXIMATELY 10 MPH OVER A SPEED BUMP, A LOUD NOISE WAS HEARD UNDERNEATH THE VEHICLE. THE CONTACT NOTICED THAT THE FRONT GRILL ASSEMBLY WAS DETACHED AND THE PLASTIC PIECE FRACTURED INTO PIECES. THE VEHICLE WAS TAKEN TO STEVEN MERCEDES BENZ DEALER OF SAN JOSE, CA WHERE IT WAS DETERMINED THAT THE FAILURE WAS NOT A KNOWN ISSUE AND NOT COVERED BY THE WARRANTY. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND STATED THAT THERE WAS NO RECALL OR WARRANTY COVERAGE. THE FAILURE WAS NOT REMEDIED. THE FAILURE MILEAGE WAS APPROXIMATELY 96,000.

NHTSA ID

10991418

Incident

May 17, 2017

Mileage

96,000 mi

TRANSMISSION COOLER WHICH IS IN RADIATOR CRACKED AND ALLOWED TRANSMISSION FLUID TO ENTER MOTOR COOLING SYSTEM AND COOLANT TO ENTER TRANSMISSION COMPLETELY RUINING THE TRANSMISSION ALL COMPONENTS AND COMPUTER TALKED TO MERCEDES THEY WOULD DO OOHING ABOUT TOTAL COST TO REPAIR $5000.00

NHTSA ID

10717074

Incident

Apr 1, 2015

Mileage

59,000 mi

STRONG ODOR OF GAS AFTER FILL THE TANK UP. THE ODOR WAS OUTSIDE, AND IT EVENTUALLY DISAPPEARED WHEN THE LEVEL OF GAS IS LOWER. THERE WAS ALSO GAS LEAKING UNDERNEATH (DRIVER'S REAR SIDE). I WAS TOLD TO REPLACE THE FUEL GASKET, AFTER DOING THAT, THE ODOR IS NOW INSIDE THE CAR, CONSTANT FUEL ODOR, IT NEVER DISAPPEAR. DRIVING THE CAR IS IMPOSSIBLE, AND GAS LEAKING UNDERNEATH CONTINUES, SAME SPOT. *TR

NHTSA ID

10664204

Incident

Jul 1, 2014

Mileage

79,000 mi

I AM WRITING TO INFORM YOU OF A VERY TROUBLING INCIDENT THAT OCCURRED RECENTLY. I OWN A 2008 MERCEDES BENZ CL550 WITH 31,000 MILES ON THE ODOMETER. ON JUNE 16, 2014, THE SEATBELT ON MY VEHICLE WOULD NOT RELEASE FROM THE SEAT, LEAVING ME UNABLE TO BUCKLE MY SEAT. ON TOP OF THE OBVIOUS SAFETY HAZARD, ILLEGALITY OF DRIVING WITHOUT A SEAT BELT, CONSTANT DINGING FROM THE VEHICLE TO REMIND ME THAT I WAS NOT BUCKLED, WHICH DID NOT ALLOW ME TO SPEAK WITH MY CLIENTS BY PHONE IN THE VEHICLE, I HAD TO DEAL WITH VERY POOR HANDLING OF THIS MATTER BY MBUSA. I IMMEDIATELY BROUGHT THE CAR INTO FLETCHER JONES MERCEDES BENZ IN NEWPORT BEACH AND HAD MY SERVICE ADVISOR TAKE THE CAR IN TO CHECK OUT THE SEAT BELT MALFUNCTION AND CALLED ME TO TELL ME IT NEEDED TO BE REPLACED AND THAT MERCEDES BENZ USA (MBUSA) WOULD BE COVERING 75% OF THE COST OF THE PART AS A GESTURE OF 'GOODWILL', LEAVING ME WITH ABOUT $400 OF COSTS FOR LABOR AND 25% OF THE PART. WHILE I WAS APPRECIATIVE OF THIS GESTURE, I WAS NOT HAPPY ABOUT HAVING TO PAY ANYTHING DUE TO THE FAILURE OF A BASIC VEHICLE SAFETY FEATURE. HE SAID THAT I WOULD HAVE TO TAKE THIS UP WITH MBUSA DIRECTLY. I BROUGHT THE ISSUE TO THEIR ATTENTION OF MBUSA AND THEY REFUSED TO DO ANYTHING FURTHER. THE FACT THAT A COMPANY LIKE MBUSA WOULD NOT STAND BEHIND THEIR PRODUCT AND TAKE FULL RESPONSIBILITY FOR A VERY IMPORTANT ISSUE SUCH AS A SEAT BELT FAILURE IS QUITE DISTURBING. HIDING BEHIND A WARRANTY WHEN PEOPLES LIVES ARE AT STAKE IS AN IRRESPONSIBLE COMPANY LINE TO TAKE. I WOULD LIKE TO BRING THIS ISSUE TO THE ATTENTION OF THE NHTSA IN HOPES THAT THIS FAILURE IS DOCUMENTED AND READILY VERIFIABLE, SHOULD ANY UNFORTUNATE CONSUMER BE INJURED OR KILLED BY THIS DEFECTIVE PRODUCT IN THE FUTURE. *TR

NHTSA ID

10605381

Incident

Jun 16, 2014

Mileage

31,000 mi

MY 2008 MERCEDES BENZ CL550 IS HAVING A PROBLEM WITH BRAKE. THERE IS A THUG-THUG SOUND WHEN I PRESS DOWN ON THE BRAKE PEDAL. IT GOES AWAY ~2 SECONDS AFTER THE GEAR IS PUT INTO PARKING OR NEUTRAL POSITION. MERCEDES BENZ KNOWS ABOUT THE PROBLEM AND THEY TOLD ME THAT THERE IS ANOTHER CAR, A S CLASS, THAT IS HAVING A SAME PROBLEM. S CLASS IS 4 DOOR VERSION OF CL CLASS. MB TOLD ME THAT THEY ARE WORKING ON A NEW PART OVER 3 MONTHS AGO AND NOW THEY ARE TELLING ME THAT THEY ARE WORKING ON A SOFTWARE TO FIX A PRESSURE PROBLEM IN A VALVE. I DON'T UNDERSTAND THE DETAILS BUT IT SURE SOUNDS LIKE AN ENGINEERING ISSUE MEANING A DEFECT. MB SAID THE ISSUE IS LIMITED TO A VERY SMALL NUMBER OF VEHICLES BUT I AM NOT SURE IF THAT IS THE CASE. NOISE WAS NOT READILY NOTICEABLE BUT GOT LOUDER SO PEOPLE MIGHT NOT NOTICE IT UNTIL LATER. I AM VERY CONCERNED BECAUSE MY BRAKE PEDAL ALSO FEELS MUCH SOFTER AND WEAKER (NEED TO PRESS DOWN FURTHER). I HAD THIS PROBLEM FOR ~4 MONTHS. *TR

NHTSA ID

10311670

Incident

Sep 15, 2009

Mileage

4,000 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system • Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. • If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system • Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. • If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. • The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) • Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation• If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: • LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304