2012 Mercedes-Benz CLS63

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

I have a 2012 Mercedes-Benz CLS63 that is leaking fuel from the rear driver side by the tire. You can smell fuel inside the cabin of the vehicle very strong. On the vin plate on my door it says in my vehicle is built on April 2011 which would qualify it for the recall from Mercedes. Per NHTSA.

NHTSA ID

11686824

Incident

Sep 9, 2025

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint The customer requests deactivation of the N112/9 HERMES communication module Note: Deactivation of the HERMES control unit (N112/9) is not supported for gray-market vehicles. Cause Before deactivating the HERMES control unit (N112/9), it must be clarified by the legal department of the respective MPC whether and under what conditions deactivation may be carried out. If deactivation is not permissible under applicable law, the HERMES control unit (N112/9) must not be deactivated. Remedy Please inform the customer that, following deactivation, the vehicle will no longer be able to place an automatic emergency call, nor will the customer be able to place a manual emergency call. After deactivation, the Mercedes-Benz Digital Extras will also no longer be available. Please have the attached sample form checked by your market's legal department, adapted to local requirements if necessary, and approved. Furthermore, after informing the customer about the effects of deactivation, please have the workshop complete and sign the approved form together with the customer, and send it to the MPC via a TIPS case for audit-compliant documentation. Furthermore, the workshop must affix a sticker to the emergency call button cover on the overhead control panel and to the emergency call button itself. After affixing, pictures of the overhead control panel need to be attached to the TIPS case for audit-proof documentation. After deactivation, the HERMES control unit (N112/9) is in the "Out of Service" operating status, and the display "SOS NOT READY" appears in the Audio/COMAND system. This display message tells the customer that the emergency call function is not available. In detail, the following steps must be carried out 1. The workshop must inform the customer about the effects of deactivation (see above) 2. Legal review by the MPC Legal department to determine whether deactivation is permissible for the vehicle and provision of a market-specific customer form based on the examples (see "Example - Deactivation communication module HERMES customer declaration English V3.0.pdf") 3. Completion of the market-specific customer form by the workshop and obtaining the customer’s signature 4. Creation of a XSS ticket by the workshop for the MPC with the signed customer form attached 5. Written confirmation of legally reviewed and approved deactivation by the MPC in the TIPS case (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, point 1) 6. Creation of an XSS ticket for documentation of the SA code "09o" (zero nine oh) in the Vehicle Documentation System (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, steps 2–7) 7. Ordering of stickers (part number A9078172900), quantity: 2 8. Affixing of the sticker (part number A9078172900) to the cover of the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 9. Affixing of the sticker (part number A9078172900) to the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 10. Taking photos of the applied stickers and attaching them to the TIPS case 11. After the XSS ticket has been successfully processed, the communication module must be deactivated using XENTRY: • Connect XENTRY Diagnosis • Access the HERMES control unit (N112/9) • "Adaptation" tab, menu item "Teach-in processes" -> "Deactivation" • Follow the instructions

Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"