2022 Mercedes-Maybach S 580 4MATIC

Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic /9G‑TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G‑TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on‑going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: ‑ NAG3 Classic (automatic transmission 725.0) ‑ NAG3 Classic ‑ AMG sport model (AMG 43 and AMG 53 with converter, automatic transmission 725.0) ‑ NAG3 Classic ‑ Hybrid (automatic transmission 725.0) ‑ NAG3 Classic ‑ AMG 63 (automatic transmission 725.0) ‑ NAG3 MOPF ISG2 (automatic transmission 725.1) ‑ NAG3 MOPF Hybrid (automatic transmission 725.1) ‑ NAG3 MOPF AMG sport model (AMG 53/AMG 53e with ISG48V2 & converter /hybrid, automatic transmission 725.1) ‑ NAG3 MOPF AMG 43/63 with engine 139/177 (automatic transmission 725.1) Steps for the Service Advisor: Important: The more information and detail that can be given to the workshop about the complaint, then the more effective the subsequent diagnosis with IPR can be. To this end, a detailed service reception questionnaire has been provided to help the Service Advisor ask the right questions about the complaint. ‑ Ask precise details about the customer complaint and the conditions and context. ‑ Fill out the service reception questionnaire (please see WIS document: OF27.00‑P‑3000‑05A) for customer complaints in detail and forward it to the workshop. Operation steps for the workshop employee: 1. Perform quick test 2. Access the transmission control unit via XENTRY Diagnosis 3. Select "A customer complaint has been received" and carry out all subsequent operation steps (IPR diagnosis path). 4. The IPR repair instructions are displayed, Carry out the IPR repair instructions without performing any further diagnostic or repair steps. ‑ Important: The IPR repair instructions are binding and must be carried out. Differing repairs are possible; such repairs must be documented in XENTRY in free text. Please observe the information regarding the IPR diagnosis process in XENTRY. Conventional diagnosis and subsequent appropriate repairs are only permitted if IPR does not specify any repair instructions. Invoicing for the guided IPR steps: Operation item 27‑0640 and 0.1 hours Notice regarding warranty: The use of IPR in association with warranty claims is mandatory! If the IPR repair instructions are disregarded without justification, the warranty claims may be rejected and/or are subject to debit. IPR will provide a measure to repair the vehicle based on various data sources (EEPROM, fault codes, etc). Please consider the vehicle maintenance record of the vehicle. For warranty and goodwill repairs, the transmission ECU test log and/or IPR test result must be uploaded into Paperless XENTRY Diagnosis (pXD) . If repair is being determined based of oil pan condition pictures of oil pan MUST be provided to warranty as justification. ·Tamper‑proof documentation: The IPR repair instructions are stored in the control unit log. Please file this document in a tamperproof manner ‑ either in digital form or as a hard‑copy printout and also enclose a printout with the damaged part. In this regard, please comply with the country‑specific warranty requirements of the MPC/general distributor.

Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

Complaint CEL illuminates and/or AC does not blow cold. Cause Potentially relevance to hardware and/or software Remedy Scenario 1: 1. If the AC does not blow cold air, replace compressor (if compressor's index and part number Figure 1 match against Table 1). a. If the compressor does not fall within Table 1, please open a TIPS case. b. Flush procedure must be followed as per WIS. Scenario 2: 1. If AC does blow cold. a. Follow the following procedure: i. Have the air conditioning system recharged. ii. Clear the fault codes afterward. iii. Let the vehicle stand for 8 hours (OBD reset condition). iv. Check whether the fault is still present. b. Open TIPS case with your findings and answers the following questions, send to the HV/LV inbox. i. When exactly did the MIL appeared (immediately at start‑up or while driving). ii. What was the ambient temperature, any special driving maneuvers, and whether the vehicle had just come out of a climate‑controlled garage.

A software update will be performed that provides enhancements to the robustness and system stability of the communication module. The update is free of charge and runs in the background, which takes about 8 minutes to install. During this time, the vehicle can be driven without any restrictions, and the new software will be active with the next ignition cycle. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Dear Dealer Partners, The part numbers listed in the chart below should no longer be installed and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is Thursday, October 8th, 2026. After October 8th, we will no longer accept returns of these parts. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. We will replace all returned parts in accordance with the chart below.