2024 Mercedes-Maybach S 680

I was peed for theses cars and the never giving the car and not giving my money back and also I have the contract with him

NHTSA ID

11623299

Incident

Oct 9, 2024

Complaint Crackling and cracking noise from the outer wheel on the front axle when cornering Cause The noise is generated by a micromovement on the contact surface between the rim and the brake disk (wheel bolt group) and may be intensified by potential soiling. The more lightweight rim (AMG forged rim) transmits the noise louder; in the case of cast rims, the noise is generally not perceptible. This is not a technical defect, but rather a complaint concerning comfort. Safe operation of the vehicle is ensured at all times. Remedy Important note: The operations described below do not represent a permanent remedy in every case. The noise may reoccur again after an indefinite period of time; sanding the rims with abrasive media multiple times is not permissible. Only cleaning using the Hazet tool 4960-160 (recommendation) can be performed without any concerns each time the wheel is changed or if the complaint reoccurs. Replacing the parts (rim, wheel bolts, wheel bearings, wheel hub, brake disk) is not expedient in the event of this complaint. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Clean the components of the wheel bolt connection according to the WIS instructions Sand down the rim and brake disk bowl by performing the following steps: • Manually sand rim (old design only) in area of water drain bores (Figure 1; item A), approx. 1.5 cm left and right of water drain bore (Figure 2) Note: Use abrasive paper with grit size 80. The grooving in this area should no longer be visible (sand down approx. 0.1-0.2mm) • Also sand brake disk bowl using emery cloth or abrasive paper with a grain size of 120 • For vehicles equipped with the AMG ceramic brake system (B07), abrasive paper may not be used for cleaning on the brake disk side Note: Do not use any cleaning agent when cleaning on the rim side. Cleaning using abrasive paper with a grain size of 80 will suffice. Do not apply any grease, lubricant or paste after cleaning The brake disk bowl should be "bare metal" in the area of the imprints made by the hole (Figure 3)

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 23rd, 2026. After July 23rd, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

Complaint General information on the operation of the PRE-SAFE® Impulse system: The PRE-SAFE® Side Impulse system is a preventive, i.e. pre-collision occupant protection system. The task of the system is to provide additional protection to vehicle occupants when there is a risk of a side impact. It is not a restraint system component in the conventional sense and does not contain an detonator. A potential side-impact situation is detected by radar sensors. If the system detects an existing likelihood of a side impact, a reversible air cushion in the outer seat side bolster is briefly inflated by opening a valve. The resulting pulse preemptively increases the distance between the door and the occupant in order to move the occupant out of the danger zone. If the system has been activated, the following message appears on the instrument cluster: PRE-SAFE® Side Impulse inoperative. See Operator's Manual. Note: After system activation, diagnostic entry B1B3713 or B1B3813 is marked as active and stored in the ORC223 (N2/5) control unit. Cause After activation of the “PRE-SAFE® Side Impulse” system, the function is no longer available. Remedy Please check the tight seating and possible damage of the radar sensors B29/11 or B29/12. Then replace the gas generator on the affected side (R12/65 or R12/66). After replacing the gas generator (R12/65 or R12/66), please perform commissioning and SCN coding of the radar sensors B29/11 or B29/12 to ensure they are up to date. Note: In principle, it is not necessary to replace the air cushion in the "PRE-SAFE® Side Impulse" system, as it is designed for multiple activations (up to 10). Exception: After deployment of the sidebag (e.g., following a crash), exchange (air cushion with gas generator) of the "PRE-SAFE ® Impulse Side" is required in all cases.