RoadVitals

1997 Oldsmobile Silhouette Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Data refreshed

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
Recall campaignsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
9
Newest Feb 17, 2009
Carrying an NHTSA advisoryCampaigns where NHTSA told owners not to drive the vehicle, or to park it outside, until the repair is done.
0
Open investigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0
7 investigations on file

Recall campaigns

9 campaigns cover this model year — what the defect is, what it could cause, and what the remedy is

09E005000

STEERING

Feb 17, 2009
979 units potentially affected
The defect: DORMAN IS RECALLING 979 STEERING KNUCKLES, DORMAN P/NOS. 697-902 AND 697-903, SOLD UNDER DORMAN'S "OE SOLUTIONS<SUP>TM</SUP>" BRAND NAME, AND NAPA P/NOS. 7-8502 AND 7-8503 WHICH WERE SOLD FOR REPLACEMENT USE ON THE VARIOUS VEHICLES LISTED ABOVE. A POTENTIAL MATERIAL OR DESIGN DEFECT COULD RESULT IN THE STEERING KNUCKLE BREAKING IN THE HUB AREA.
The risk: A BROKEN STEERING KNUCKLE COULD RESULT IN LOSS OF STEERING CONTROL AND A POSSIBLE CRASH WITHOUT WARNING.
The remedy: DORMAN WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE STEERING KNUCKLES FREE OF CHARGE AND REIMBURSE THE REPAIR FACILITY OR OWNER FOR LABOR. THE RECALL BEGAN ON FEBRUARY 23, 2009. OWNERS MAY CONTACT DORMAN'S TOLL-FREE HOTLINE AT 1-800-523-2492 AND PRESS 5.
DORMAN PRODUCTS, INC.View on NHTSA.gov
08E050000

EXTERIOR LIGHTING:HEADLIGHTS

Aug 11, 2008
1,921 units potentially affected
The defect: K2 MOTOR IS RECALLING 1,921 AFTERMARKET HEADLAMPS OF VARIOUS MODELS SOLD FOR USE ON THE ABOVE LISTED VEHICLES. THESE HEADLAMPS ARE MISSING THE AMBER SIDE REFLEX REFLECTOR WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."
The risk: WITHOUT THE AMBER SIDE REFLEX REFLECTORS, THE LIGHTING VISIBILITY MAY BE AFFECTED, POSSIBLY RESULTING IN A VEHICLE CRASH.
The remedy: K2 MOTOR WILL NOTIFY OWNERS AND OFFER A FULL REFUND. THE RECALL BEGAN ON DECEMEBER 17, 2008. OWNERS MAY CONTACT K2 MOTOR AT 1-909-839-2992.
K2 MOTOR CORPORATIONView on NHTSA.gov
07E021000

FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY:PRESSURE RELIEF DEVICES

Mar 12, 2007
742 units potentially affected
The defect: CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.
The risk: FUEL MAY LEAK, POSSIBLY RESULTING IN A FIRE.
The remedy: DELPHI WILL NOTIFY OWNERS AND REPLACE THE UPR FREE OF CHARGE. THE RECALL BEGAN ON APRIL 23, 2007. OWNERS CAN CONTACT DELPHI AT 877-411-8770.
DELPHIView on NHTSA.gov
04V597000

LATCHES/LOCKS/LINKAGES:DOORS:LATCH

Dec 22, 2004
717,302 units potentially affected
The defect: ON CERTAIN MINIVANS EQUIPPED WITH SECOND-ROW BUCKET SEATS OR CAPTAIN'S CHAIRS AND A POWER SLIDING DOOR ON THE PASSENGER SIDE OF THE VEHICLE, A PASSENGER USING THE INTERIOR HANDLE TO OPEN THE POWER SLIDING DOOR COULD BE INJURED.
The risk: IF A PASSENGER USES THE INTERIOR HANDLE TO OPEN THE POWER SLIDING DOOR AND HOLDS ONTO THE HANDLE WHILE IT IS BEING OPENED BY THE MOTOR, THE PASSENGER'S ARM MAY BE PUSHED INTO THE SEAT BACK OR ARMREST AND A WRIST OR LOWER ARM INJURY MAY RESULT.
The remedy: DEALERS WILL REPLACE THE POWER SLIDING DOOR INTERIOR HANDLE ON THE PASSENGER-SIDE. IF THE VEHICLE IS EQUIPPED WITH A POWER OR MANUAL SLIDING DOOR ON THE DRIVER-SIDE, THE INTERIOR HANDLE WILL ALSO BE REPLACED FOR APPEARANCE REASONS. NOTE: BEFORE THE VEHICLE IS SERVICED, GM ADVISES OWNERS TO NOT USE THE INTERIOR DOOR HANDLE TO OPEN THE DOOR. THE DRIVER CAN OPEN AND CLOSE THE DOOR FROM SWITCHES AT THE DRIVER'S POSITION OR BY USING THE REMOTE KEY FOB. THE DRIVER SHOULD TELL PASSENGERS TO USE THE SWITCH LOCATED IN FRONT OF THE DOOR TO OPEN OR CLOSE IT. THE DRIVER SHOULD USE THE OVERRIDE SWITCH TO PREVENT OPERATION OF THE POWER DOOR BY CHILDREN OR BY OTHERS WHO ARE NOT FAMILIAR WITH ITS USE. THE OWNER NOTIFICATION LETTER MAILING WILL BE CONDUCTED IN PHASES WITH THE FIRST PHASE BEGINNING ON MAY 31, 2005. THE SECOND PHASE MAILING BEGAN ON JULY 18, 2005. THE RECALL BEGAN ON MAY 31, 2005. PHASE 2 BEGAN ON JULY 18, 2005. PHASE 3 (FINAL PHASE) BEGAN ON AUGUST 24, 2005, TO ALL REMAINING CUSTOMERS. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438; PONTIAC AT 1-800-620-7668; OR OLDSMOBILE AT 1-800-630-6537.
GENERAL MOTORS CORP.Manufacturer number 04110View on NHTSA.gov
02V286000

STEERING:RACK AND PINION

Nov 4, 2002
1,159,156 units potentially affected
The defect: CERTAIN PASSENGER VEHICLES AND MINI VANS HAVE LOWER PINION BEARINGS IN THE POWER RACK AND PINION ASSEMBLY IN WHICH THE RETAINER TABS WERE NOT CRIMPED PROPERLY. THESE AND SOME OTHER RETAINERS USED IN VEHICLES ASSEMBLED BETWEEN JANUARY 1, 1996 AND OCTOBER 31, 1997, COULD FAIL AND PERMIT THE BALL BEARINGS TO ESCAPE.
The risk: IF THIS OCCURS, THE PINION SHAFT CAN BE FORCED UPWARD DURING LEFT TURNS AND BACK DOWN AS THE STEERING WHEEL IS MOVED BACK AND TO THE RIGHT. IF THE PINION SHAFT MOVES FURTHER, THE DRIVER WILL NEED TO EXERT MORE EFFORT TO TURN THE STEERING WHEEL, SIMILAR TO A VEHICLE WITHOUT POWER ASSISTED STEERING. IF THE PINION SHAFT MOVES EVEN FURTHER, THE DRIVER WILL REQUIRE MUCH HIGHER EFFORT TO TURN LEFT AND MAY NOT BE ABLE TO TURN THE WHEEL AS MUCH AS INTENDED. WITH THE MAXIMUM PINION SHAFT MOVEMENT, WHICH REQUIRES INTERNAL GEAR COMPONENT DAMAGE, THE DRIVER CAN ENCOUNTER HIGH RESISTANCE TO TURNING LEFT, FOLLOWED BY UNINTENDED POWER ASSIST TO THE RIGHT. IN ANY OF THESE CONDITIONS, A CRASH COULD OCCUR.
The remedy: DEALERS WILL INSTALL A NEW LOWER PINION BEARING UNLESS INSPECT OF THE EXISTING BEARING INDICATES THAT REPLACEMENT OF THE GEAR ASSEMBLY IS NECESSARY. OWNER NOTIFICATION BEGAN JANUARY 24, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020, PONTIAC AT 1-800-762-2737, OR OLDSMOBILE AT 1-800-442-6537.
GENERAL MOTORS CORP.Manufacturer number 02049View on NHTSA.gov
01V264000

LATCHES/LOCKS/LINKAGES:DOORS:LATCH

Aug 21, 2001
248,737 units potentially affected
The defect: VEHICLE DESCRIPTION: 1997-2001 CHEVROLET VENTURE, PONTIAC MONTANA/TRANSPORT, AND OLDSMOBILE SILHOUETTE MINI VANS EQUIPPED WITH PASSENGER SIDE POWER SLIDING DOORS THAT WERE SERVICED IN CAMPAIGN 01013 (01V-067) FROM APRIL TO AUGUST 2001. ALSO 2001 CHEVROLET VENTURE, PONTIAC MONTANA, AND OLDSMOBILE SILHOUETTE MINI VANS EQUIPPED WITH PASSENGER SIDE POWER SLIDING DOORS ASSEMBLED IN JANUARY THROUGH APRIL 2001. THESE VEHICLES HAVE INADEQUATE FRONT WELDS. IF A FRONT WELD FAILS, THE ACTUATOR CAN JAM IN THE UNLATCHED POSITION AND, WHEN THE SLIDING DOOR CLOSES, IT WILL NOT BE LATCHED.
The risk: IF THIS HAPPENS, THE POWER SLIDING DOOR CAN OPEN WHILE THE VEHICLE IS IN MOTION, PARTICULARLY WHEN THE VEHICLE ASCENDS A HILL, MAKES A TURN, OR TRAVELS OVER A ROUGH ROAD SURFACE. AN UNRESTRAINED OCCUPANT COULD FALL OUT OF THE VAN AND BE INJURED.
The remedy: DEALERS WILL INSPECT AND, IF REQUIRED, INSTALL A NEW POWER SLIDING DOOR UNLATCH ACTUATOR ASSEMBLY. OWNER NOTIFICATION BEGAN ON OCTOBER 22, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020, PONTIAC AT 1-800-762-2737, OR OLDSMOBILE AT 1-800-442-6537.
GENERAL MOTORS CORP.Manufacturer number 01059View on NHTSA.gov
01V067000

LATCHES/LOCKS/LINKAGES:DOORS:LATCH

Mar 8, 2001
477,011 units potentially affected
The defect: VEHICLE DESCRIPTION: MINIVANS EQUIPPED WITH PASSENGER SIDE POWER SLIDING DOORS. THE DOOR CLOSES BUT MAY NOT BE LATCHED. IF THIS HAPPENS, THE POWER SLIDING DOOR CAN OPEN WHILE THE VEHICLE IS IN MOTION, PARTICULARLY WHEN THE VEHICLE ASCENDS A HILL, MAKES A TURN, OR TRAVELS OVER A ROUGH ROAD SURFACE.
The risk: AN UNRESTRAINED OCCUPANT COULD FALL OUT OF THE VAN AND BE INJURED.
The remedy: DEALERS WILL INSTALL A NEW UN-LATCH ACTUATOR ASSEMBLY TO THE POWER SLIDING DOOR. THIS RECALL HAS BEEN CONTINUED UNDER SAFETY RECALL 01V-264. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020, PONTIAC AT 1-800-762-2737, OR OLDSMOBILE AT 1-800-442-6537.
GENERAL MOTORS CORP.Manufacturer number 01013View on NHTSA.gov
98V145000

SEATS:FRONT ASSEMBLY:RECLINER

Jun 26, 1998
125,990 units potentially affected
The defect: VEHICLE DESCRIPTION: PASSENGER MINI VANS EQUIPPED WITH BUCKET SEATS OR A SPLIT BENCH SEAT IN THE SECOND (MIDDLE) OR THIRD (BACK) ROW. THE SEAT LATCH MECHANISMS ON BUCKET SEATS AND ON THE 40% PORTION OF THE SPLIT BENCH SEAT IN THE SECOND AND THIRD ROWS DO NOT HAVE PROTECTIVE COVERS.
The risk: WHEN ACTIVATING THE RELEASE MECHANISM TO ROLL A BUCKET SEAT FORWARD, A CUSTOMER'S FINGER(S) COULD BE SEVERELY INJURED OR SEVERED IN THEY ARE NOT KEPT CLEAR OF THE MECHANISM.
The remedy: DEALERS WILL INSTALL PROTECTIVE COVERS ON THE OUTBOARD LATCH MECHANISMS ON ALL LEFT AND RIGHT HAND REAR BUCKET SEATS IN THE SECOND AND THIRD ROW, AND TO BOTH INBOARD AND OUTBOARD LATCH MECHANISMS ON THE CENTER REAR BUCKET SEAT AND THE 40% PORTION OF THE SPLIT BENCH SEAT.
GENERAL MOTORS CORP.View on NHTSA.gov
98V072000

VISIBILITY:WINDSHIELD WIPER/WASHER:LINKAGES

Apr 7, 1998
55,154 units potentially affected
The defect: VEHICLE DESCRIPTION: PASSENGER MINI VANS EQUIPPED WITH TRACTION CONTROL SYSTEMS. THE WINDSHIELD WIPER LINKAGE ARM CAN CONTACT A BRAKE LINE WHICH IS CONNECTED TO THE TRACTION CONTROL SYSTEM MODULATOR VALVE. THIS CONTACT CAN CHAFE THE BRAKE LINE RESULTING IN A BRAKE FLUID LEAK.
The risk: BRAKE FLUID LEAKAGE CAN CAUSE REDUCED BRAKE EFFECTIVENESS AND INCREASED STOPPING DISTANCES.
The remedy: DEALERS WILL INSTALL A BRAKE LINE CLIP TO ENSURE PROPER CLEARANCE. ALSO THE BRAKE LINES WILL BE INSPECTED TO ANY DAMAGE CAUSED BY THIS CONDITION AND WILL REPLACE ANY DAMAGED LINES.
GENERAL MOTORS CORP.View on NHTSA.gov

What a recall is

Safety recall
A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation
NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Safety investigations

NHTSA inquiries naming this vehicle. An investigation is not a finding of a defect, and it is not a recall.

EA03005ClosedEngineering Analysis

REAR AXLE TRAILING ARM FAILURE

Opened Apr 23, 2003
Closed Jan 12, 2004

ON NOVEMBER 18, 2002, ODI OPENED A PRELIMINARY EVALUATION (PE02-086) TO EVALUATE ALLEGATIONS OF REAR AXLE TRAILING ARM FAILURES IN THE SUBJECT VEHICLES (U-VAN) WHICH INCLUDED TWO REPORTING CRASHES.ON APRIL 9, 2003, ODI UPGRADED PE02-086 TO AN ENGINEERING ANALYSIS (EA03-005) TO CONTINUE ITS EXAMINATION OF THE ISSUE. THE TRAILING ARM DESIGN IN THESE VEHICLES HAS BEEN USED IN THE U-VAN FROM MY 1997 THROUGH THE PRESENT.THE GM ANALYSIS CONCLUDED THAT THE SUBJECT TRAILING ARMS COULD CRACK OR BUCKLE IF THEY WERE DAMAGED DURING ASSEMBLY, PRE-DELIVERY HANDLING, OR SUBJECTED TO CERTAIN SERVICE RELATED ABUSE CONDITIONS SUCH AS IMPROPER TOWING OR JACKING.ANALYSIS OF ODI AND GM DATA HAS IDENTIFIED 19 INCIDENTS OF REAR AXLE TRAILING ARM FAILURES IN THE SUBJECT VEHICLES.THERE HAVE BEEN NO NEW REPORTS TO ODI OR GM IN THE LAST 12 MONTHS AND ONLY ONE NEW COMPLAINT IN THE LAST 21 MONTHS. DUE TO THE LOW COMPLAINT RATE AND THE ABSENCE OF A CONTINUING TREND IN REPORTED FAILURES, A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY, THIS INVESTIGATION IS CLOSED. THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST. THE AGENCY WILL TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES. FOR ADDITIONAL INFORMATION, SEE THE ATTACHED CLOSING REPORT.

SUSPENSION
EA02032ClosedEngineering Analysis

SAFETY BELT ASSEMBLY FAILURE

Opened Nov 18, 2002
Closed Nov 21, 2003

ODI IDENTIFIED 59 REPORTS WITH THE ALLEGED DEFECT.ODI WAS ABLE TO CONTACT 44 OF THE 59 CONSUMERS IN ORDER TO DETERMINE THE SPECIFIC CAUSE OF THE LATCH PROBLEMS.OF THE 44 OWNERS CONTACTED, ODI DETERMINED THAT FOUR FAILURES WERE DUE TO AN OUT-OF-TOLERANCE LATCH PLATE, AND THAT 23 FAILURES WERE DUE TO A DISPLACED BUCKLE HOUSING COVER.THE REMAINING 17 FAILURES HAD INDETERMINABLE CAUSES.OF THE 59 REPORTS, THERE WERE THREE ALLEGED MINOR INJURIES.NO LEGAL CLAIMS OR LAWSUITS HAVE BEEN FILED WITH REGARD TO THIS ALLEGED DEFECT.BASED ON THE LIMITED NUMBER OF REPORTS, AND A DECLINING REPORT TREND, THIS INVESTIGATION IS CLOSED.A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEARED TO BE WARRANTED.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES. SEE ADDITIONAL SUMMARY REPORT.

SEAT BELTS
EA02003ClosedEngineering Analysis

POWER RACK AND PINION STEERING FAILURE

Opened Apr 4, 2002
Closed Dec 10, 2002

THE LOWER PINION BEARING IN THE RACK AND PINION STEERING ASSEMBLY MAY FAIL.GM WILL RECALL 1997-98 GRAND PRIX BUILT BETWEEN 1-MAR-96 AND 31-OCT-97; AND 1996-98 U-VANS/J-CARS BUILT BETWEEN 1-JAN-96 AND 31-OCT-97.SEE ATTACHED SUMMARY.

STEERINGLed to recall 02V286000
PE02017ClosedPreliminary Evaluation

SHOULDER HARNESS CLIP

Opened Feb 11, 2002
Closed Aug 2, 2002
SEAT BELTS
PE01038ClosedPreliminary Evaluation

STEERING RACK AND PINION

Opened Nov 14, 2001
Closed Apr 4, 2002

ODI HAS RECEIVED 200 COMPLAINTS FROMT CONSUMERS AND 1,238 FROM GM ALLEGING FAILURE OR LOCKUP OF THE STEERING RACK AND PINION UNIT (R&P).THIS ALLEGED CONDITION CAN RESULT IN THE LOSS OF STEERING CONTROL OF THE VEHICLE AND A CRASH CAN RESULT.GM HAS REPORTED SIX CRASHES IN WHICH EIGHT PEOPLE HAVE SUSTAINED INJURIES RANGING FROM BRUISES, AIRBAG BURN, SEAT BELT ABRASION, FACIAL INJURY, NECK AND BACK PAIN.ALL CRASHES WERE SINGLE VEHICLE CRASHES.GM STATES THAT ONE POSSIBLE FAILURE MODE IS FAILURE OF THE LOWER PINION BEARING IN THE R&P.AN ENGINEERING ANALYSIS HAS BEEN OPENED TO DETERMINE IF A SAFETY DEFECT TREND EXISTS.

STEERING
SQ00014ClosedInvestigation

UNEXPECTED OPENING OF SLIDING DOOR

Opened Jul 25, 2000
Closed Oct 22, 2001

There is no summary currently available

STRUCTURELed to recall 01V067000

Showing 6 of 7 inquiries on file for this model year, open ones first. Every one of them is listed on NHTSA.gov.

Elsewhere on this vehicle

Data sources

Data on this page last refreshed .