2009 Yamaha FJR1300 Problems

I WAS RIDING AT ABOUT 30MPH ON A HIGHWAY AND THE ENGINE SUDDENLY DIED. I HAD TO COAST OVER TO THE SHOULDER TO STOP. THE GAUGES STAYED ON, THE KILL SWITCH WAS IN THE RUN POSITION, BUT THE ENGINE WOULD NOT START (STARTER WOULD NOT ENGAGE) UNTIL I TURNED THE IGNITION KEY OFF THEN BACK ON. THEN IT STARTED BACK UP AS USUAL, AND I RODE ON TO WORK. THESE ARE THE SAME SYMPTOMS DESCRIBED IN THE RECALLS # 09V-002 AND 11V-338 WHICH WERE PERFORMED ON MY BIKE IN 2011 (MODIFICATION NUMBERS FROM YAMAHA 990051 AND 990061) BUT APPARENTLY THE BIKE IS NOT FIXED AND APPEARS TO BE DANGEROUS TO RIDE SINCE IT LOST ENGINE POWER WITHOUT WARNING AT SPEED. PER THE RECALL INSTRUCTIONS, THE WIRE SUBLEAD WAS REPLACED BUT THE WIRE HARNESS ASSEMBLY WAS NOT REPLACED. PERHAPS THE MAIN WIRE HARNESS IS DEFECTIVE AND NEEDS TO BE REPLACED?

ENGINE INTERMITTENTLY CUTS-OUT. CUT-OUT LASTS FOR A SECOND OR LESS AND MAY REPEAT ITSELF SEVERAL TIMES BEFORE OPERATING PROPERLY AGAIN. MAY CUT-OUT SEVERAL TIMES IN 10 MILE DAILY COMMUTE. WHEN ENGINE IS CUTTING-OUT, IT IS A COMPLETE LOSS OF ENGINE POWER. VERY UNSAFE SITUATION WHEN TRAVELING ON FREEWAY IN TRAFFIC. IGNITION SWITCH AND WIRING HARNESS RECALL WORK HAS BEEN COMPLETED AND PROBLEM HAS NOT BEEN RESOLVED. *TR

I WAS RIDING AT ABOUT 30MPH ON A HIGHWAY AND THE ENGINE SUDDENLY DIED. I HAD TO COAST OVER TO THE SHOULDER TO STOP. THE GAUGES STAYED ON, THE KILL SWITCH WAS IN THE RUN POSITION, BUT THE ENGINE WOULD NOT START (STARTER WOULD NOT ENGAGE) UNTIL I TURNED THE IGNITION KEY OFF THEN BACK ON. THEN IT STARTED BACK UP AS USUAL, AND I RODE ON TO WORK. THESE ARE THE SAME SYMPTOMS DESCRIBED IN THE RECALLS # 09V-002 AND 11V-338 WHICH WERE PERFORMED ON MY BIKE IN 2011 (MODIFICATION NUMBERS FROM YAMAHA 990051 AND 990061) BUT APPARENTLY THE BIKE IS NOT FIXED AND APPEARS TO BE DANGEROUS TO RIDE SINCE IT LOST ENGINE POWER WITHOUT WARNING AT SPEED. PER THE RECALL INSTRUCTIONS, THE WIRE SUBLEAD WAS REPLACED BUT THE WIRE HARNESS ASSEMBLY WAS NOT REPLACED. PERHAPS THE MAIN WIRE HARNESS IS DEFECTIVE AND NEEDS TO BE REPLACED?

THE PROBLEM I AM ABOUT TO DESCRIBE HAS BEEN OCCURRING SINCE THE MOTORCYCLE WAS NEW. HOWEVER, DUE TO RESEARCH, I AM ONLY NOW ABLE TO REPORT THE PROBLEM. ON HOT DAYS, WHEN THE MOTORCYCLE IS PARKED OUTSIDE, AFTER STARTING, IT STUMBLES AND CUTS OUT DURING ACCELERATION. THE LAST INCIDENT (WHICH I AM NOW REPORTING ON) ALMOST CAUSED ME TO GET HIT IN A PARKING LOT WHEN THE MOTORCYCLE DIED ACCELERATING FROM A STOP SIGN. A VEHICLE AT THE ADJACENT STOP SIGN ALMOST HIT ME WHEN I STALLED OUT. THE RESEARCH I'VE DONE POINTS TO THE EMISSION CONTROL CHARCOAL CANISTER AS BEING THE PROBLEM. ONCE IT BECOMES SATURATED, IT EFFECTS THE INTAKE, AND THEN CAUSES STUMBLING AND CUTTING OUT. IF THE MOTORCYCLE CAN BE RIDDEN AT HIGHWAY SPEED, THE CANISTER CLEARS AND THE MOTORCYCLE OPERATES IN A NORMAL MANNER. HOWEVER, A DANGEROUS SITUATION EXISTS PRIOR TO ITS CLEARING. *TR

THE PROBLEM I AM ABOUT TO DESCRIBE HAS BEEN OCCURRING SINCE THE MOTORCYCLE WAS NEW. HOWEVER, DUE TO RESEARCH, I AM ONLY NOW ABLE TO REPORT THE PROBLEM. ON HOT DAYS, WHEN THE MOTORCYCLE IS PARKED OUTSIDE, AFTER STARTING, IT STUMBLES AND CUTS OUT DURING ACCELERATION. THE LAST INCIDENT (WHICH I AM NOW REPORTING ON) ALMOST CAUSED ME TO GET HIT IN A PARKING LOT WHEN THE MOTORCYCLE DIED ACCELERATING FROM A STOP SIGN. A VEHICLE AT THE ADJACENT STOP SIGN ALMOST HIT ME WHEN I STALLED OUT. THE RESEARCH I'VE DONE POINTS TO THE EMISSION CONTROL CHARCOAL CANISTER AS BEING THE PROBLEM. ONCE IT BECOMES SATURATED, IT EFFECTS THE INTAKE, AND THEN CAUSES STUMBLING AND CUTTING OUT. IF THE MOTORCYCLE CAN BE RIDDEN AT HIGHWAY SPEED, THE CANISTER CLEARS AND THE MOTORCYCLE OPERATES IN A NORMAL MANNER. HOWEVER, A DANGEROUS SITUATION EXISTS PRIOR TO ITS CLEARING. *TR

WHILE REASSEMBLING MY MOTORCYCLE (DUE TO AN UNRELATED REPAIR), THE FUEL TANK BEGAN TO LEAK DUE TO A HOLE WORN INTO THE TANK FROM A HEX BOLT THAT HOLDS ON A PLASTIC REAR SKIRT. IT APPEARS THAT SEVERAL YEARS OF ABRASION, DUE TO THE HEX BOLT MOUNTING HOLE BEING TOO CLOSE TO THE TANK (POSSIBLY DUE TO A MANUFACTURING OR ASSEMBLY DEFECT) CAUSED THE TANK METAL TO BECOME COMPROMISED. WHEN I REASSEMBLED THE MOTORCYCLE THE HEX BOLT WAS ABLE TO PENETRATE THE WALL OF THE WEAKENED METAL, THUS CAUSING THE HOLE. MY MAIN CONCERN IS THAT THIS LEAK COULD HAVE OCCURRED WHILE RIDING, AND WOULD HAVE RESULTED IN A FIRE. THE DEALERSHIP IS WORKING WITH YAMAHA ON THIS MATTER, SO I HAVE YET TO SEE WHERE YAMAHA STAND ON THIS ISSUE. HOWEVER, I AM QUITE CONCERNED THAT OTHERS' THAT OWN THIS MOTORCYCLE MIGHT BE AT RISK. NOTE: MY MILEAGE FIGURE IS AN ESTIMATE. *TR