RoadVitals

1993 BMW 325 Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Data refreshed

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
Recall campaignsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
3
Newest Aug 10, 1994
Carrying an NHTSA advisoryCampaigns where NHTSA told owners not to drive the vehicle, or to park it outside, until the repair is done.
0
Open investigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0
1 investigation on file

Recall campaigns

3 campaigns cover this model year — what the defect is, what it could cause, and what the remedy is

94V151000

SEAT BELTS:FRONT:ANCHORAGE

Aug 10, 1994
57,000 units potentially affected
The defect: IN A FMVSS NO. 208 30 MILES-PER-HOUR COMPLIANCE TEST, AN UNBELTED TEST DRIVER DUMMY'S CHEST MAXIMUM RESULTANT ACCELERATION WAS 70.8 G'S, WHICH EXCEEDS THE MAXIMUM ALLOWABLE VALUE OF 60 G'S. ALSO, THE UNBELTED PASSENGER DUMMY'S LEFT FEMUR MAXIMUM LOAD WAS 2361 LBS, WHICH EXCEEDS MAXIMUM ALLOWABLE VALUE OF 2250 LBS. THE VEHICLES DO NOT COMPLY WITH FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."
The risk: CONSEQUENCE OF NON-COMPLIANCE: IN THE EVENT OF AN ACCIDENT, THE OCCUPANT WILL BE SUBJECTED TO AN INCREASED RISK OF INJURY.
The remedy: ON AUTOMATIC TRANSMISSION MODELS ONLY, THE DEALER WILL REPLACE THE TRANSMISSION SUPPORT CROSSMEMBER WITH A CROSSMEMBER USED ON THE MANUAL TRANSMISSION MODEL. ALSO, THE TRANSMISSION REAR BUSHING SUPPORTS WILL BE REPLACED WITH BUSHING HAVING DIFFERENT PERFORMANCE CHARACTERISTICS. THE STEERING COLUMN FRONT SUPPORT BEARING AT THE FIREWALL WILL BE REPLACED WITH A MODIFIED PART USING A TEFLON INNER SURFACE AND TEFLON SPRAY WILL BE APPLIED TO THE COLUMN HOUSING IN THE AREA OF THE BEARING. A BRACE WILL BE ADDED BETWEEN THE KNEE BOLSTER SUPPORT AND THE STEERING COLUMN.
BAYERISCHE MOTOREN WERKEView on NHTSA.gov
94V066000

FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS

Apr 11, 1994
116,300 units potentially affected
The defect: FEED FUEL HOSES CAN HARDEN AND "SET" OVER TIME, ALLOWING A SEEPAGE OF FUEL AT THE CONNECTION BETWEEN THE HOSE AND THE ENGINE FITTING. THE CLAMP USED TO HOLD THE HOSE TO THE FITTING IS UNABLE TO COMPENSATE FOR THE HARDENING OF THE FEED FUEL HOSE.
The risk: FUEL SEEPAGE BETWEEN THE FEED FUEL HOSE AND THE ENGINE FITTING CAN RESULT IN FREE FUEL IN THE ENGINE COMPARTMENT, WHICH COULD RESULT IN A FIRE WHEN EXPOSED TO A SOURCE OF IGNITION.
The remedy: A REDESIGNED FEED FUEL HOSE AND HOSE CLAMP WILL BE INSTALLED TO ALLEVIATE THE FUEL SEEPAGE.
BAYERISCHE MOTOREN WERKEView on NHTSA.gov
93V015000

VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:HEATER CORE

Feb 1, 1993
375,000 units potentially affected
The defect: THE MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT RESULTS IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND A RESULTING INCREASE IN SYSTEM PRESSURE.
The risk: VEHICLES OPERATED UNDER THIS INCREASED COOLING SYSTEMPRESSURE CONDITION CAN SUFFER DAMAGE OR FAILURE OF PARTS OF THE COOLING SYSTEMSUCH AS (1) LEAKAGE FROM A COOLANT HOSE, (2) LEAKAGE OF THE RADIATOR OREXPANSION TANK, (3) DISCONNECTION OF A HOSE FROM A PIPE OR A FITTING, AND (4)CRACKS IN THE HEATER CORE END PIECE RESULTING IN COOLANT LEAKAGE. IN SOME CASES,BOILING COOLANT CAN CONTACT THE LOWER RIGHT LEG OF THE DRIVER RESULTING INBURNS. ALSO, ESCAPING COOLANT IN THE PASSENGER COMPARTMENT CAN CAUSE VAPORFOGGING OF THE INTERIOR SURFACE OF THE WINDOWS, REDUCING DRIVER VISIBILITY.
The remedy: DEALERS WILL INSTALL A THERMOSTATIC BYPASS VALVE IN THE ENGINE COMPARTMENT TO CONTROL COOLANT TEMPERATURE IN THE HEATER CORE. ALSO, A NEW DESIGN RADIATOR CAP WILL BE INSTALLED, TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
BAYERISCHE MOTOREN WERKEView on NHTSA.gov

What a recall is

Safety recall
A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation
NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Safety investigations

NHTSA inquiries naming this vehicle. An investigation is not a finding of a defect, and it is not a recall.

EA95013ClosedEngineering Analysis

AIR BAG WIRING FAILURE

Opened Mar 31, 1995
Closed Jul 15, 1996

There is no summary currently available

AIR BAGSLed to recall 96V110000

Elsewhere on this vehicle

Data sources

Data on this page last refreshed .