Reports submitted to NHTSA by owners and drivers, shown in full
Data refreshed
Our database holds 51 NHTSA owner-reported complaints for the 2005 BMW R 1200 Gs. Each one is a report filed by an owner or driver and published by NHTSA without most of them being verified. A complaint is not a confirmed defect, not a recall and not a manufacturer bulletin. Narratives are shown exactly as filed.
Complaints are reports submitted by owners and drivers to NHTSA. They are not verified and do not establish that a defect exists.
Showing 1–25 of 51 · page 1 of 3
UPON INSPECTION, I DISCOVERED 4 OF THE 5 WHEEL MOUNTING HOLES IN THE ALUMINUM REAR WHEEL FLANGE ARE CRACKED. I HAVE READ ABOUT MANY PEOPLE HAVING THIS ISSUE WITH THIS MODEL VEHICLE. I'VE STOPPED RIDING UNTIL IT IS FIXED BECAUSE IT COULD BREAK CAUSING AN ACCIDENT WHICH COULD LEAD TO INJURY OR DEATH. *TR
AFTER NOTICING A SMALL AMOUNT OF EXCESSIVE MOVEMENT IN THE REAR WHEEL WHEN RIDING THROUGH TURNS, I GOT HOME AND INSPECTED THE AREA AND FOUND CRACKS IN THE ALUMINUM REAR WHEEL FLANGE AT THE WHEEL MOUNTING HOLES. AFTER RESEARCHING THE ISSUE, I DISCOVERED THIS IS A RECALLED PART UNDER RECALL CAMPAIGN 15V-141. THE RECALL INSTRUCTS REPLACING THE ALUMINUM FLANGE WITH A NEW STEEL FLANGE. FURTHERMORE, ASSOCIATED SERVICE BULLETINS 3300115(007) AND 3300115(007)R3 DISPLAY IMAGES OF THE RECALLED ALUMINUM FLANGE FOR EASY IDENTIFICATION AND INSTRUCTS DEALERSHIPS TO REPLACE THE ALUMINUM FLANGE WITH A NEW STEEL ONE, EVEN IF NO CRACKS ARE PRESENT. MY FLANGE DOES MATCH THE IMAGES IDENTIFYING IT AS THE ALUMINUM FLANGE IN QUESTION. ALSO, TO BE THOROUGH, I PLACED A MAGNET ON THE FLANGE, AND IT DID NOT STICK. IT WOULD HAVE STUCK TO A STEEL FLANGE. ACCORDING TO THE DETAILS OF THE RECALL ON THE NHTSA SITE, THE RECALL DOES COVER THE YEAR AND MODEL OF MY VEHICLE, BUT, WHEN I RESEARCH MY VIN, THE RECALL DOES NOT SHOW UP.
LEAKING FUEL FLANGED, THE MATERIAL IS MADE OF PLASTIC AND PRONE TO BREAKING THAT CAN CAUSE FUEL TO LEAK TO THE ENGINE THEN IGNITING THE FUEL THAT WILL START ENGINE FIRE.
TL* THE CONTACT OWNS A 2005 BMW R1200 GS. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 20 MPH, FUEL HAD LEAKED FROM THE FUEL PUMP FLANGE AND SPRAYED ONTO THE RIDERS LEG AND PARTS OF THE MOTORCYCLE. THE CAUSE OF THE FAILURE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER AND AN UNKNOWN LOCAL DEALER WERE NOTIFIED OF THE FAILURE BUT NO ASSISTANCE WAS OFFERED. THE CONTACT WAS INFORMED THAT THE MOTORCYCLE WAS NOT INCLUDED IN THE NHTSA CAMPAIGN NUMBER: 13V617000 (FUEL SYSTEM) ALTHOUGH THE MOTORCYCLE HAD EXPERIENCED THE SAME FAILURE LISTED IN THE RECALL. THE FAILURE MILEAGE WAS 24,000.
ABS PUMP FAILURE.
I EXPERIENCED A 100% NO BRAKES SITUATION COMING INTO A SLOW SPEED 90 DEGREE TURN ON A BACK ROAD. LUCKILY I HADN'T BEEN GOING TO FAST AND WAS ABLE TO DOWN SHIFT AND SCRUB A LITTLE SPEED BUT FORCED WITH ONLY ENGINE BRAKING AND A VERY OLD ASPHALT ROAD COVERED IN GRAVEL I HAD TO LAY IT DOWN TO STOP FROM GOING INTO A 60FT+ RAVINE. I'VE PUT 250-300K OF STREET RIDING UNDER MY BUTT AND THIS IS THE FIRST TIME I'VE LAID A BIKE DOWN. I DID HURT MY LEFT LEG AND I HAVE A HUGE BRUISE THERE NOW AND MY CRASH BARS PREVENTED ANY MAJOR DAMAGE TO THE BIKE BUT IT DID STILL CAUSE ABOUT $500 IN DAMAGES. I'M WELL AWARE OF THE PROBLEMS THAT THE 05-06 SERVO BIKES HAVE HAD WITH BRAKE FAILURE BUT I'VE ALWAYS READ THAT THE RESIDUAL BRAKES ARE STILL THERE IF THE SERVOS FAIL. I CAN ATTEST I HAD ZERO BRAKES! LEVER WENT TO THE BARS AND REAR JUST FELL DOWN AND HAD NOTHING. I'VE ACTUALLY PRACTICE A COUPLE PANIC STOPS WITH THE IGNITION OFF TO EXPERIENCE WHAT JUST THE RESIDUAL BRAKE FEEL LIKE AND I WAS ABLE STOP FAIRLY NORMAL WITH JUST SOME INCREASE EFFORT. THIS WAS NOT THAT! AFTER THE CRASH I TURNED OFF THE BIKE AND ANOTHER RIDER HELPED ME PICK IT UP. UPON TURNING IT BACK ON I STILL HAD ZERO BRAKES THE LEVER JUST WENT TO THE BARS AND REAR HAD NOTHING. WHEN I TURNED THE BIKE BACK ON I HAD THE ABS AND BRAKE FAILURE LIGHTS FLASHING AND THE SERVO NEVER KICKED ON TO DO ITS BIT CYCLE. SO ME AND THE OTHER GUY SAT THERE TALKING ABOUT WHAT JUST HAPPENED AND ABOUT 2 MINUTES OR SO WENT BY AND ALL OF A SUDDEN THE SERVOS KICKED ON AND ALL THE WARNING LIGHTS WENT OFF AND MY BRAKES WHERE BACK TO NORMAL!!! I TURNED THE BIKE OFF AND NOW I HAD RESIDUAL BRAKES AGAIN! THIS FAILURE COULD HAVE VERY WELL KILLED ME IF IT HAPPENED IN MULTIPLE AREAS EARLIER IN THE RIDE. A QUICK GOOGLE SEARCH SHOWS THAT THIS HAS HAPPENED TO NUMEROUS PEOPLE. *TR
UPON REPLACING REAR TIRE AT THE BMW DEALERSHIP, NOTICED A CRACKED REAR WHEEL FLANGE. THESE CRACKS APPEARED ON 4 OF 5 ATTACHMENT POINTS WHERE THE FLANGE BOLTS ONTO THE REAR DRIVE. THIS IS A PART THAT HOLDS THE WHEEL TO THE MOTORCYCLE. SPOKE TO BMW NA AND THEY DO RECOGNIZE THE PROBLEM AS INHERENT DEFECT, AND HAVE NOT RECALLED DESPITE HAVING REDESIGNED THE REPLACEMENT PART SEVERAL TIMES OVER THE LAST FEW YEARS (IMPLIED ADMISSION BY BMW OF THE INHERENT DEFECT DUE TO REDESIGN). THIS IS SAFETY ISSUE RELATED TO AN INHERENT DEFECT OF SAFETY CRITICAL PART - THE REAR WHEEL FLANGE. FAILURE OF THIS PART WHILE THE VEHICLE IS BEING OPERATED MAY CAUSE LOSS OF REAR BRAKE FUNCTION, LOSS OF STEERING ABILITY, SUDDEN SEIZURE OF REAR WHEEL, AND/OR POSSIBLE LOSS OF REAR WHEEL. THIS MAY LEAD TO SERIOUS INJURY AND EVEN DEATH. *TR
TL* THE CONTACT OWNS 2005 BMW R1200 GS. THE CONTACT STATED THAT WHILE INSPECTING THE MOTORCYCLE, THE CONTACT DISCOVERED THAT THERE WAS A CRACK ON THE REAR WHEEL FLANGE. THE MOTORCYCLE WAS TAKEN TO A DEALER WHERE IT WAS DIAGNOSED WITH A FRACTURED WHEEL FLANGE. THE MANUFACTURE WAS MADE AWARE OF THE FAILURE. THE FAILURE AND CURRENT MILEAGE WAS 47,000.
REPLACED REAR TIRE AND NOTICED CRACKS ON HUB FLANGE. WENT ONLINE TO SEE IF ANY BODY ELSE HAD SAME PROBLEM . FOUND MANY OTHER COMPLAINTS. YEARS 2004-2007. PART WAS REDESIGNED AND REPLACED FROM 2008 THRU PRESENT. WANT TO REPORT BEFORE SOMEBODY DIES OR IS SERIOUSLY INJURED. NEEDS TO BE RECALLED BY BMW. *TR
I WAS REPLACING MY REAR BRAKE ROTOR. THE ROTOR IS BOLTED TO A PIECE CALLED A FLANGE (PART NUMBER 33117722831) USING 5 BOLTS. I FOUND THAT EACH OF THE 5 BOLT HOLES IN THE FLANGE ARE CRACKED. IF THIS PART WERE TO COME APART WHILE RIDING I THINK IT WOULD CAUSE THE REAR WHEEL TO LOCK UP AND SKID OR POSSIBLY WORSE. THE FLANGE (PART NUMBER 33117722831) IS ALSO PART OF THE POWER TRAIN AND REAR WHEEL DRIVE SYSTEM (ALSO KNOWN AS THE FINAL DRIVE SYSTEM) FOR THE BMW R1200GS MOTORCYCLE. THE BMW MUST KNOW THAT THIS IS A DANGEROUS PROBLEM BECAUSE THEY HAVE REDESIGNED THE PART. SEARCHING THE INTERNET FOR "BMW R1200GS FLANGE CRACK" RETURNS MANY PAGES OF INFORMATION ON THIS PROBLEM. HERE IS A GOOD SUMMARY: HTTP://WWW.MTS1200.INFO/MOTORCYCLEINFO/INDEXE65D.HTML?FA=CONTENTGENERIC.NKYQIUKEVRYEUZUT&PAGEID=360814. *TR
FUEL IS LEAKING FROM THE HIGH PRESSURE OUTPUT FITTING OF THE GAS TANK. FUEL LEAKS WHEN FUEL PUMP IS ON, VISIBLY DRIPPING. WHEN THE FUEL PUMP IS OFF THERE IS NO LEAK. FUEL LEAKS ACTIVELY AND EXCESSIVELY FROM OUTPUT FITTING, WHICH APPEARS TO BE CRACKED. *TR
FUEL LEAKING AT THE FUEL PUMP FLANGE AS WELL AS AT THE SUCTION PUMP FLANGE AROUND THE BASE OF THE QUICK DISCONNECT FITTING.
SMELLED FUEL, REMOVED LEFT SIDE COVER, SAW TOP OF FUEL PUMP COVERED WITH GAS. IT IS LEAKING FROM THE PLASTIC QUICK DISCONNECT. ALSO SEE CRACKS IN THE FLANGE ON TOP OF FUEL PUMP. THIS IS A FIRE HAZARD, CAUSED BY POOR DESIGN THAT USES TAPERED PIPE THREAD IN PLASTIC. *TT
FUEL PUMP FLANGE CRACKED AT FUEL PUMP OUTPUT CONNECTOR AND FUEL SPRAYED OUT UNDER PRESSURE. PRESSURIZED FUEL SPRAYED ON LEG AND HIT HOT ENGINE EXHAUST. WAS ABLE TO CUT OFF ENGINE AND FUEL PUMP BEFORE A FIRE STARTED. HAD TO WAIT SEVERAL HOURS BEFORE HELP ARRIVED AND TRUCKED BIKE HOME. *TR
FAULTY FUEL STRIP GAS GAUGE WILL SHOW 1/2 TANK, BUT TANK MAY BE FULL OR EMPTY, OR SOMEWHERE IN BETWEEN. LIKEWISE, GAS GAUGE MAY SHOW FULL, BUT TANK MAY BE CLOSE TO EMPTY. THE FUEL STRIP DOES NOT CORRECTLY DISPLAY THE AMOUNT OF FUEL IN THE TANK. *TR
CRACKS HAVE BEEN FOUND IN THE FUEL LINE INPUT FLANGE @ FUEL PUMP AND THE RETURN FUEL FLANGE. *TR
STOPPED AFTER RIDING TO WORK, NOTICED FUEL SMELL, LOOKED CLOSER, GAS WAS DRIPPING ON HOT EXHAUST PIPE. TURNS OUT THE FUEL LINE PLASTIC QUICK DISCONNECT THREADED BOSS ON THE FUEL TANK WAS CRACKED ENOUGH THAT GAS LEAKS OUT WHEN THE FUEL PUMP IS RUNNING. JUST NOW REPORTING ALTHOUGH IT FIRST HAPPENED YEARS AGO. TRIED VARIOUS REPAIRS THAT WERE ONLY TEMPORARILY EFFECTIVE BEFORE REPLACING THE ENTIRE FUEL PUMP ASSY AND REINFORCING THE BOSS WITH AN AFTERMARKET SPECIALTY CLAMP DESIGNED FOR THIS WELL KNOWN FAILURE. *TR
REAR WHEEL/BRAKE DISK DRIVE FLANGE HAS MULTIPLE CRACKS, COULD HAVE CAUSED REAR WHEEL OR BRAKE ROTOR TO SEPARATE FROM MOTORCYCLE. BMW KNOWS THIS IS A SAFETY ISSUE, THE REPLACEMENT PART BMW # 33117722831 HAS BEEN COMPLETELY REDESIGNED AND MADE FROM STEEL NOW, THIS ITEM NEEDS TO BE RECALLED, IT COULD EASILY CAUSE LOSS OF CONTROL AND DEATH. *TR
THE FUEL PUMP FITTING CRACKED WHILE I WAS RIDING ON THE HIGHWAY. THIS RESULTED IN FUEL SPRAYING ON ME AND DRIPPING ONTO THE ENGINE WHEN I STOPPED. THE FITTING AND THE FLANGE ARE BOTH MADE OF A PLASTIC MATERIAL. THE THREADS ARE NPT TYPE AND AS THE FITTING IS SCREWED INTO THE FUEL PUMP FLANGE THE FIT GETS TIGHTER. THIS DESIGN WILL EVENTUALLY RESULT IN CRACKING. THIS IS WHAT HAPPENED TO THE PLASTIC FITTING WHICH I REPLACED WITH A METAL ONE. THIS WILL NOT SOLVE THE PROBLEM BECAUSE THE FLANGE IS LIKELY TO CRACK BECAUSE OF THE DESIGN RESULTING IN ANOTHER FAILURE. THIS TYPE OF FAILURE CAN EASILY RESULT IN A FIRE. *TR
UPON INSPECTION, I DISCOVERED THAT EACH OF FIVE WHEEL MOUNTING TABS ON THE REAR WHEEL FLANGE IS CRACKED. THIS HAS BEEN REPORTED IN NUMEROUS OTHER BMW R1200GS MOTORCYCLES, IN SOME CASES LEADING TO CATASTROPHIC FAILURE. *TR
TL* THE CONTACT OWNS A 2005 BMW R1200GS MOTORCYCLE. THE CONTACT STATED THAT THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC FOR UNRELATED MAINTENANCE WHEN THEY NOTICED THAT THE REAR WHEEL FINAL DRIVE WAS SEVERELY WORN. THE PART WAS ORDERED AND THE VEHICLE WAS LATER REPAIRED. THE REAR BRAKE PADS WERE REPLACED DURING THE REPAIR DUE TO AN EXCESSIVE OIL LEAK FROM THE REAR WHEEL. THE DRIVE SHAFT WAS ALSO DAMAGED AND WOULD NEED TO BE REPLACED. THE MANUFACTURER WAS NOT NOTIFIED OF THE PROBLEM. THE APPROXIMATE FAILURE MILEAGE WAS 68,000. UPDATED 06/10/13 *BF THE CONSUMER STATED THE FINAL DRIVE SEAL BLEW WHILE DRIVING. THE REAR TIRE WAS COVERED IN OIL. IN ADDITION, THE REAR BRAKE PAD HAD TO BE REPLACE DUE TO OIL DAMAGE. WHILE REPAIRING THE FINAL DRIVE. THE MECHANIC FOUND THE DRIVE SHAFT WAS NOTCHY AND NEEDED TO BE REPLACED.
DURING SERVICE, TECH NOTICED A CRACK IN THE FUEL PUMP HOUSING. BIKE IS UNSAFE TO DRIVE DUE TO RISK OF FUEL LEAK AND FIRE HAZARD. THIS PROBLEM IS WELL DOCUMENTED AND COULD POTENTIALLY LEAD TO LOSS OF LIFE OR SEVERE BURNS. RECOMMEND RECALL ON THIS PART. *TR THE ISSUE IS SO WELL KNOWN, ONLINE PARTS STORES ARE SELLING A PARTS FIX. REQUEST REASON WHY RECALL HAS NOT BEEN ISSUED.
AFTER FILLING UP ON FUEL AND DRIVING HOME (LESS THAN FIVE MILES), I PARKED THE MOTORCYCLE. LATER IN THE DAY, I NOTICED FUEL ON THE ASPHALT BENEATH THE BIKE AND LEAKING FROM THE FUEL PUMP, DOWN ONTO THE ENGINE, LEFT EXHAUST PIPE AND OTHER PARTS OF THE FRAME. FURTHER INSPECTING, I FOUND FUEL POOLED ATOP THE FUEL PUMP HOUSING. MOPPING UP THE FUEL, I IDENTIFIED A HAIRLINE CRACK IN THE UPPER PLASTIC HOUSING THAT HOLDS THE FUEL PUMP, FUEL PUMP ELECTRONICS AND FUEL LINE CONNECTION. THE FUEL PUMP ELECTRONICS UNIT WAS DAMAGED BY EXPOSURE TO THE FUEL, CAUSING SILICON INSULATION TO CRUMBLE AND FALL AWAY. (EVIDENCE THAT THE LEAK HAD EXISTED FOR SOME TIME, BUT ONLY CAME TO MY ATTENTION AFTER THIS PARTICULAR FILL-UP.) REPLACEMENT PARTS ESTIMATE FROM BMW: $680.34 (INCLUDING TAX, BUT EXCLUDING INSTALLATION.) *TR
DISCOVERED 12/9/2012. EXTENT OF CRACKING INDICATES THAT THE ISSUE LIKELY BEGAN A NUMBER OF YEARS EARLIER. MY FUEL TANK HAS PLASTIC QUICK DISCONNECT FITTINGS ON LEFT AND RIGHT SIDE. NUMEROUS (8-12) SMALL RADIAL CRACKS HAVE APPEARED IN EACH OF THE QUICK DISCONNECT REINFORCEMENT FLANGES, EXTENDING IN SEVERAL CASES DOWN TO THE TOP OF THE TANK. CONTINUED GROWTH OF THE CRACKS INTO THE THREADED AREA HAVE RESULTED IN FUEL LEAKS ON OTHER BIKES WITH THIS SAME CONFIGURATION (BUT NOT YET ON MY BIKE). BELIEF IS THAT THE COMPOSITE QUICK DISCONNECT EXPANDS DURING PRESSURE CYCLING AND IMPARTS A RADIAL LOAD TO THE PUMP HOUSING QUICK DISCONNECT REINFORCEMENT FLANGE. OVER TIME, THIS PRESSURE CYCLING CAUSES CRACKS TO APPEAR IN THE REINFORCEMENT FLANGE WHICH EVENTUALLY RESULT IN FUEL LEAKS. SEE ODI 10428629 AND CASE [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR
FUEL STARTED LEAKING FROM TOP OF GAS TANK , LEAKING FROM CRACKS IN FLANGE CONNECTION VERY UNSAFE FIRE HAZARD. *TR
Higher-selling and older vehicles accumulate more reports. Counts are not failure rates and are not directly comparable between vehicles that sold in very different numbers.
Categories with enough reports to have a page of their own
Data on this page last refreshed .