2008 BMW R 1200 RT Problems

The bike is a 2008 BMW R1200RT. The throttle bodies for each cylinder has a plastic cam that is the point of attachment for the throttle cable. That plastic cam broke and completely detached from the bike. I was accelerating to merge into traffic on Interstate 64E at Corydon, IN. Once established in the right lane, the bike suddenly lost power and slowed rapidly while I was approached from the rear by a tractor trailer that had to apply brakes and continuously sounded his horn while abruptly maneuvering to the left lane to avoid me while I was attempting to assess what had just happened. This is a critical safety component and its failure has been documented countless number of times on various owner's group forums for this type of bike. One of which is linked here: https://www.bmwsporttouring.com/topic/91897-throttle-body-more-cracked-cable-camspulleys/ Another: https://forums.bmwmoa.org/showthread.php?76036-Broken-Throttle-Body-Pulleys-2009-R1200RT/page5 It is apparent the plastic that this throttle body cam is made from deteriorates rapidly causing a significant safety risk. There are aftermarket replacements that are made from aluminum, but they are very expensive. I am asking for a safety recall and that BMW be made to replace these parts with a metal or a material that is less prone to failure.

My forth vehicle with throttle body cams that are cracked and broken on both sides. No symptoms or warning lights of a problem that could have lead to a catastrophic failure, total engine propulsion failure, breakdown. My safety and others were in danger of injury or death. Dealer has confirmed and repaired all vehicles.

ABS PUMP MOTOR IS FAILING ON MANY OF THE SAME MODEL BIKES AND SOME OTHER 2006-2008 MODEL BMW BIKES WITH LOW MILEAGE, BECAUSE THE BRUSH HOLDERS IN THE ABS ELECTRICAL MOTOR ARE TOO TIGHT AND BRUSHES GET STUCK IN THEM - BAD DESIGN OF THE ABS PUMP MOTOR. BMW WILL ASK YOU LOADS OF MONIES FOR THE REPLACEMENT OF THE PUMP, EVEN THO THEY ARE FULLY AWARE IT'S A PROBLEM WITH MANY OF THE BIKES.

THE BRAKE FAILURE LIGHT CAME ON, BMW SHOP SAID ABS UNIT IS BAD $2000 FIX. ON MANY BMW MOTORCYCLE FORUMS THERE ARE MANY ABS UNIT FAILURES. BMW KNOWS ABOUT THESE FAILURES BUT DOES NOTHING.

WITH JUST 16124 MILES, MY MOTORCYCLE HAS A FINAL DRIVE RING BEARING FAILURE. THE BMW DEALER DIAGNOSED THE PROBLEM WHEN CONDUCTING THE REAR FLANGE RECALL REPAIR. THIS FAILURE IS SO COMMON THAT IT HAS BECOME ENDEMIC. BMW OFFERS NO HELP WITH THE REPAIR AN OBVIOUS DESIGN ERROR.

I WAS RIDING ALONG AT ABOUT 50 MPH WHEN THE MOTORCYCLE BEGAN EXPERIENCING A LACK OF STABILITY AND DIRECTIONAL CONTROL. IT FELT LIKE I HAD A FLAT TIRE. AT THE SAME TIME THERE WAS LOUD RUMBLING AND A VIBRATION FELT THROUGHOUT THE BIKE. *TR

VEHICLE BEGAN EXHIBITING ENGINE STALLING SYMPTOMS FOR ABOUT A MONTH (ENGINE DIES WITHOUT WARNING AS IF IGNITION HAD BEEN CUT) DURING CITY DRIVING, WHILE TURNING AND PULLING INTO A PARKING SPACE AT ABOUT 5 MPH, THE VEHICLE ENGINE QUIT ALONG WITH INSTRUMENT PANEL GOING BLANK. ELECTRICAL SMOKE BEGAN TO BILLOW BETWEEN THE FRONT FORKS. THIS LASTED FOR ABOUT 10 SECONDS. AFTER GETTING THE VEHICLE HOME, I DISCOVERED THAT THE FIRE APPEARED TO HAVE ORIGINATED IN THE IGNITION WIRING HARNESS SOMEWHERE BETWEEN THE FRONT FORKS. THE HARNESS WRAP APPEARS TO HAVE FRICTION WEAR INDICATIONS EXPOSING BARE WIRING. THE FAULTY WIRE MELTED THE INSULATION ALL THE WAY FROM THE IGNITION SWITCH DOWN INTO THE MAIN WIRING HARNESS THAT IS ROUTED UNDER THE FUEL TANK.

2008 BMW R1200RT (MOTORCYCLE) ENGINE STALLS WHILE IN OPERATION. THIS OCCURRED 3 OCCASIONS DURING A COMMUTE. FIRST STALL AFTER ACCELERATION. RESTARTED ENGINE. APPROXIMATELY 1/2 MILE DOWN THE ROAD TRAVELING 45 MPH SECOND ENGINE STALL OCCURS. RESTARTED ENGINE.. THIRD ENGINE STALLS OCCURS WITHIN ANOTHER MILE OF THE SECOND STALL ON A BUSINESS LOOP. RESTARTED ENGINE. EACH TIME THE ENGINE STALLED I WAS FORCED TO ENTER THE SHOULDER OF THE ROAD WHILE AVOID TRAFFIC BEHIND MY MOTORCYCLE. EACH TIME THE STALL OCCURRED THEIR WAS NO VISIBLE OR AUDIBLE CUE THE ENGINE WAS NO LONGER IN OPERATION THE ENGINE SIMPLY QUIT. *TR

TL* THE CONTACT OWNS A 2008 BMW R 1200 RT MOTORCYCLE. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 15V141000 (WHEELS); HOWEVER, THE MANUFACTURER AND DEALER REFUSED TO HONOR THE REMEDY WHICH MENTIONED THE REPLACEMENT OF THE ALUMINUM REAR WHEEL FLANGE WITH A STEEL ONE. THE DEALER ONLY WANTED TO INSPECT THE VEHICLE. THE MANUFACTURER WAS NOTIFIED OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE.