1995 Chevrolet C10 Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Data refreshed yesterday

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov

Recall campaigns

Newest May 11, 2009

Carrying an NHTSA advisory

Open investigations

1 investigation on file

Recall campaigns

12 campaigns cover this model year — what the defect is, what it could cause, and what the remedy is

09E025000

EXTERIOR LIGHTING:HEADLIGHTS

May 11, 2009

42,540 units potentially affected

The defect: DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

The risk: DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.

The remedy: DOPE, INC. WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON JULY 28, 2009. OWNERS MAY CONTACT DOPE, INC. AT 1-626-272-1798.

DOPE, INC.View on NHTSA.gov

09E012000

EXTERIOR LIGHTING

Apr 7, 2009

16,270 units potentially affected

The defect: SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

The risk: DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.

The remedy: SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.

SABERSPORTView on NHTSA.gov

08E050000

EXTERIOR LIGHTING:HEADLIGHTS

Aug 11, 2008

1,921 units potentially affected

The defect: K2 MOTOR IS RECALLING 1,921 AFTERMARKET HEADLAMPS OF VARIOUS MODELS SOLD FOR USE ON THE ABOVE LISTED VEHICLES. THESE HEADLAMPS ARE MISSING THE AMBER SIDE REFLEX REFLECTOR WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

The risk: WITHOUT THE AMBER SIDE REFLEX REFLECTORS, THE LIGHTING VISIBILITY MAY BE AFFECTED, POSSIBLY RESULTING IN A VEHICLE CRASH.

The remedy: K2 MOTOR WILL NOTIFY OWNERS AND OFFER A FULL REFUND. THE RECALL BEGAN ON DECEMEBER 17, 2008. OWNERS MAY CONTACT K2 MOTOR AT 1-909-839-2992.

K2 MOTOR CORPORATIONView on NHTSA.gov

06E060000

EXTERIOR LIGHTING

Jun 29, 2006

87,745 units potentially affected

The defect: CERTAIN AAI MOTORSPORTS COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LIST PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

The risk: LACK OF AMBER SIDE REFLECTORS IN THE LAMPS WILL DECREASE LIGHTING VISIBILITY TO OTHER DRIVERS AND MAY POSSIBLY RESULT IN A VEHICLE CRASH

The remedy: AAI MOTORSPORTS WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 1, 2006. OWNERS MAY CONTACT AAI MOTORSPORTS AT 909-923-9188.

AAI MOTORSPORTS USA, LLCView on NHTSA.gov

98V187000

FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY

Aug 10, 1998

55,272 units potentially affected

The defect: VEHICLE DESCRIPTION: CREW CAB PICKUP TRUCKS. THE FRONT, INNER CORNER OF THE FUEL TANK CAN CONTACT THE BODY SILL EITHER INTERMITTENTLY OR CONSTANTLY. THIS MOVEMENT CAN CAUSE A DISCERNIBLE NOISE AND, OVER TIME, CAN WEAR A HOLE IN OR CRACK THE FUEL TANK AT POINT OF CONTACT.

The risk: THIS CONDITION CAN RESULT IN FUEL LEAKAGE AND A DISTINCT FUEL ODOR IF THE TANK WERE FILLED ABOVE THE LEVEL OF THE HOLE OR CRACK. IN THE PRESENCE OF AN IGNITION SOURCE, A FIRE COULD RESULT.

The remedy: DEALERS WILL INSPECT THE FUEL TANK FOR WEAR AND, EITHER INSTALL A SPACER BETWEEN THE FUEL TANK AND THE FRONT CROSSMEMBER, OR IF NECESSARY, REPLACE THE FUEL TANK.

GENERAL MOTORS CORP.View on NHTSA.gov

98V150001

VISIBILITY:WINDSHIELD WIPER/WASHER

Jul 1, 1998

1,557,585 units potentially affected

The defect: VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES, 2 AND 4-WHEEL DRIVE. SOLDER JOINTS NEAR THE WIRING HARNESS CONNECTOR CAN CRACK CAUSING THE WINDSHIELD WIPERS TO WORK INTERMITTENTLY.

The risk: THIS CONDITION CAN RESULT IN INOPERATIVE WIPERS, REDUCING A DRIVER'S VISIBILITY, AND INCREASING THE RISK OF A VEHICLE CRASH.

The remedy: DEALERS WILL REPLACE THE WIPER MOTOR CIRCUIT BOARD AND COVER.

GENERAL MOTORS CORP.Manufacturer number 98043View on NHTSA.gov

97V037000

SEATS

Mar 7, 1997

624,433 units potentially affected

The defect: VEHICLE DESCRIPTION: EXTENDED CAB AND 2-DOOR UTILITY VEHICLES EQUIPPED WITH RECLINING SEATS AND THE EASY-ENTRY FEATURE. THESE VEHICLES EXHIBIT A CONDITION IN WHICH A PINCH POINT EXISTS IN THE RECLINER MECHANISM THAT CAN TRAP AND PINCH A PERSON'S HAND OR FINGER(S) WHEN THE EASY-ENTRY FEATURE IS ACTIVATED.

The risk: THIS PINCHING CAN CUT THE HAND OR POSSIBLY SEVER THE FINGER(S) WITHOUT PRIOR WARNING.

The remedy: DEALERS WILL INSTALL A PROTECTOR COVER OVER THE RECLINER MECHANISM.

GENERAL MOTORS CORP.View on NHTSA.gov

96V057000

VEHICLE SPEED CONTROL

Apr 4, 1996

379,004 units potentially affected

The defect: THESE VEHICLES WERE ASSEMBLED WITH THE THROTTLE CABLE CONTACTING THE DASH MAT WHICH COULD BIND THE THROTTLE. THIS DOES NOT MEET WITH THE MAXIMUM RETURN TIMES REQUIRED BY FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 124, "ACCELERATOR CONTROL SYSTEMS."

The risk: CONSEQUENCE OF NON-COMPLIANCE: THE ENGINE SPEED MAY NOT RETURN TO IDLE INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

The remedy: DEALERS WILL INSPECT FOR ADEQUATE THROTTLE CABLE TO DASH MAT CLEARANCE, AND IF THERE IS INSUFFICIENT CLEARANCE, CUT OUT A PORTION OF THE DASH MAT TO PROVIDE PROPER CLEARANCE.

GENERAL MOTORS CORP.View on NHTSA.gov

96E010000

SEATS

Mar 25, 1996

2,400 units potentially affected

The defect: THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLES COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

The risk: IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.

The remedy: DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER'S AND PASSENGER'S SEATS.

VEHICLE SAFETY SYSTEMSView on NHTSA.gov

96V004000

STEERING: STEERING WHEEL/HANDLE BAR

Jan 2, 1996

3,047 units potentially affected

The defect: THE STEERING COLUMN UPPER INTERMEDIATE-SHAFT NUT MAY NOT BE TORQUED TO PROPER SPECIFICATIONS. THE NUT COULD LOOSEN AND DETACH ALLOWING THE THROUGH-BOLT THAT SECURES THE UPPER INTERMEDIATE-SHAFT TO THE LOWER STEERING COLUMN SHAFT JOINT TO FALL OUT.

The risk: THIS LOOSE ENGAGEMENT CAN PROVIDE NOTICEABLE NOISE AND ABNORMAL STEERING FEELING TO THE DRIVER AND, IF LEFT UNATTENDED, THE STEERING SHAFTS CAN SEPARATE RESULTING IN A LOSS OF STEERING CONTROL.

The remedy: DEALERS WILL TORQUE THE SUSPECT FASTENERS TO THE PROPER SPECIFICATIONS.

GENERAL MOTORS CORP.View on NHTSA.gov

95V242000

SEAT BELTS:FRONT

Dec 13, 1995

40 units potentially affected

The defect: THESE VEHICLES WERE BUILT WITH FRONT SEAT BELT SYSTEMS WITH NO ENERGY MANAGEMENT LOOPS AND MAY NOT MEET THE HEAD INJURY CRITERIA REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

The risk: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANTS OF THESE SEATS MAY NOT BE PROPERLY RESTRAINED.

The remedy: DEALERS WILL REPLACE THE RETRACTOR PORTION OF THE SEAT BELT ASSEMBLY(S) WITH ONE HAVING THE NEWLY DESIGNED ENERGY-MANAGEMENT TWIN-LOOP SYSTEM.

GENERAL MOTORS CORP.View on NHTSA.gov

95V241000

SEAT BELTS:FRONT

Dec 13, 1995

630,099 units potentially affected

The defect: IF BOTH THE LAP-BELT AND SHOULDER-BELT ENERGY MANAGEMENT LOOPS ON THE FRONT SEAT BELT ASSEMBLIES RELEASE AT OR NEAR THE SAME TIME, ACCELERATION FORCES CAN CAUSE THE BUCKLE RELEASE MECHANISM TO ACTIVATE AND ALLOW THE BUCKLE TO SEPARATE FROM THE LATCH.

The risk: IF THE BUCKLE RELEASED, THE SYSTEM WOULD FAIL TO PROVIDE ADEQUATE OCCUPANT RESTRAINT PROTECTION.

The remedy: DEALERS WILL REMOVE THE STITCHING THAT CREATES THE ENERGY MANAGEMENT LOOP IN THE SHOULDER BELT(S).

GENERAL MOTORS CORP.View on NHTSA.gov

Safety recall: A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation: NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication: Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Safety investigations

NHTSA inquiries naming this vehicle. An investigation is not a finding of a defect, and it is not a recall.

PE95052ClosedPreliminary Evaluation

STEERING SHAFT SEPARATIONS

Opened Oct 25, 1995

Closed Mar 22, 1996

ODI OPENED THIS PE ON NOVEMBER 13, 1995 BASED ON AN OWNER COMPLAINT CONCERNING A SEPTEMBER 1995 ACCIDENT INVOLVING A 1995 1/2 TON GM PICKUP TRUCK.THE VEHICLE OWNER ALLEGED THE BOLT USED TO JOIN THE 2-PIECE STEERING SHAFT WAS MISSING.THE SHAFTS THEN SEPARATED AND STEERING CONTROL WAS LOST. DURING THE COURSE OF THIS INVESTIGATION, ODI HAS GATHERED INFORMATION FROM STAFF AT THE FOLLOWING: AUTO COLLISION INSURANCE COMPANIES, THIRD-PARTY PRODUCTS LIABILITY INDUSTRY, INDEPENDENT REPAIR SHOPS, INVOLVED VEHICLE OPERATORS, GENERAL MOTORS CORPORATION. ACCORDING TO GM, THE STEERING COLUMN AND SHAFTS WERE CHANGED FOR THE 1995 C/K MODELS AT THE START OF THE 1995 MODEL YEAR.THE CHANGE WAS MADE TO INCORPORATE DRIVER AIR BAG SYSTEMS FOR THE C/K10/20 WITH GVWR OF LESS THAN 8500 LBS.HOWEVER THE CHANGE WAS MADE FOR ALL C/KS. FOR THE 1995 MODEL YEAR, THE STEERING COLUMN SHAFT WAS CONNECTED TO THE UPPER INTERMEDIATE SHAFT WITH A BOLT THROUGH THE COLUMN SHAFT AND THE UNIVERSAL JOINT COUPLING.NO NUT WAS REQUIRED.THIS CONNECTION WAS MADE AT THE STEERING COLUMN ASSEMBLY FACILITY AND THE STEERING COLUMN IS SHIPPED TO THE VEHICLE ASSEMBLY PLANT.THIS JOINT IS LOCATED INSIDE THE VEHICLE CAB.THE UPPER INTERMEDIATE SHAFT WAS CONNECTED TO THE LOWER INTERMEDIATE SHAFT ASSEMBLY IS ALSO CONNECTED TO THE STEERING GEAR AT THE VEHICLE ASSEMBLY PLANT. THE CONFIGURATION OF THE UPPER INTERMEDIATE SHAFT WAS CHANGED AT THE START OF THE 1996 MODEL YEAR, WITH A SMALL NUMBER OF 1996 STEERING COLUMNS PULLED AHEAD IN THE 1995 MODELS ASSEMBLED AT THE OSHAWA AND FT. WAYNE ASSEMBLY PLANTS.THE UNIVERSAL JOINT OF THE UPPER INTERMEDIATE SHAFT WAS REPLACED WITH A POT JOINT.THIS CHANGE WAS MADE TO UTILIZE A JOINT MANUFACTURED INTERNALLY INSTEAD OF EXTERNALLY SUPPLIED UNIVERSAL JOINT.THE POT JOINT STYLE CONNECTION TO THE STEERING COLUMN SHAFT WAS MADE WITH A THROUGH BOLT AND NUT.THIS CHANGE WAS EFFECTIVE FOR 1995 VEHICLES ASSEMBLED AT FT. WAYNE AND OSHAWA IN OCTOBER 1995 AND FOR ALL 1996 VEHICLES. ODI'S ANALYSIS FOUND THAT, OF THE 24 FIELD REPORTS, 14 INVOLVE VEHICLES PRODUCED AT THE FT. WAYNE ASSEMBLY PLANT.ALL 7 OF THE ACCIDENTS INVOLVE TRUCKS BUILT THERE, AS WELL.HOWEVER, BECAUSE THE FT. WAYNE ASSEMBLY PLANT PRODUCES APPROXIMATELY THE SAME NUMBER OF VEHICLES AS THE OTHER SUBJECT VEHICLE ASSEMBLY PLANTS, THIS FINDING CAN NOT BE EXPLAINED ON THE BASIS OF VEHICLE POPULATION AND EXPOSURE.ODI, WITH THE INFORMATION CURRENTLY AVAILABLE, IS UNABLE TO EXPLAIN THIS PHENOMENON.ODI DOES HAVE INFORMATION INDICATING THAT THE PROBLEM OCCURS INFREQUENTLY AND VERY EARLY IN THE LIFE OF THE VEHICLE.FOR THE 24 FIELD REPORTS, INCLUDING THOSE REPORTING ACCIDENTS, A FAILURE OCCURRED, ON AVERAGE, 129 DAYS AND 3900 MILES AFTER THE TRUCK WAS BUILT.BASED ON INFORMATION FROM ALL SOURCES, CURRENT THROUGH NOVEMBER 1995, ODI HAS FOUND THAT ONE INCIDENT HAS OCCURRED INVOLVING A SUBJECT VEHICLE BUILT SINCE JULY 8, 1995, - A PERIOD OF 257 DAYS.THE DATA REVIEWED INDICATES ACCIDENTS, ALLEGEDLY DUE TO THE SUBJECT FAILURE, OCCUR EVEN EARLIER IN ACCIDENTS, ALLEGEDLY DUE TO THE SUBJECT FAILURE, OCCUR EVEN EARLIER IN THE LIFE OF A SUBJECT TRUCK, AT AN AVERAGE OF APPROXIMATELY 103 DAYS. FINALLY, BASED ON THE 115 WARRANTY AND FILED REPORTS COMBINED, THE INCIDENT RATE IS 12/100,000 VEHICLES.OF THE 115 REPORTS, 69 INVOLVE VEHICLES BUILT AT THE JANESVILLE AND FT. WAYNE ASSEMBLY PLANTS (35 AND 34 RESPECTIVELY).THE JANESVILLE FAILURE RATE IS 15/100,000 AND THE FT. WAYNE RATE IS SLIGHTLY LOWER AT 14/100,000. A SAFETY-RELATED DEFECT HAS NOT BEEN INDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR WARRANTED.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF T

STEERING: STEERING WHEEL/HANDLE BAR

Elsewhere on this vehicle

Data sources

NHTSA Office of Defects Investigation — recall campaigns and safety investigations

Data on this page last refreshed yesterday.

1995 Chevrolet C10 Recalls

Recall campaigns

What a recall is

Safety investigations

Elsewhere on this vehicle

Data sources