Reports submitted to NHTSA by owners and drivers, shown in full
Data refreshed
Our database holds 48 NHTSA owner-reported complaints for the 2006 Chevrolet Corvette Z06. Each one is a report filed by an owner or driver and published by NHTSA without most of them being verified. A complaint is not a confirmed defect, not a recall and not a manufacturer bulletin. Narratives are shown exactly as filed.
Complaints are reports submitted by owners and drivers to NHTSA. They are not verified and do not establish that a defect exists.
Showing 1–25 of 48 · page 1 of 2
THE FRONT LIGHTS OF THE CAR ONE OF THEM ISN'T WORKING. I BELIEVE THIS ISN'T THE FIRST COMPLAIN ABOUT THIS KIND OF CAR. IT IS DANGEROUS TO BE DRIVING ON THE ROAD. I HAVE TO CONTINUE TO PUT MY HIGH BEAMS ON FOR THEM TO WORK. AT TIMES BOTH THE LIGHTS ARE ON AND WITH TIME DRIVING IT WILL TURN ONE OF THEM OFF. IT'S DANGEROUS BECAUSE THE VISIBILITY ON THE ROAD FOR ME AND OTHER DRIVERS.
VALVE RATTLE, NOT DRIVING VEHICLE TO KEEP FROM DROPPING VALVE......COSTS $4K FOR REPAIR TO HEADS....31000 MILES... IF I DRIVE IT AND DROP VALVE, WILL COST $18K TO REPLACE ENGINE ASSEMBLY.....LONG TERM VALUE OF VEHICLE DECREASES WITH NON-MATCHING NUMBERS VEHICLE. ONE HELLUVA WAY TO TREAT CUSTOMERS THAT SPEND $85K ON A VEHICLE.
I NEVER RECEIVED ANY NOTICE FROM GM, BUT I BROUGHT IT TO THE DEALER'S ATTENTION WHILE I WAS IN FOR A RECALL REPAIR IN 2008. I TOLD THE TECH THAT MY TRACTION CONTROL, ACTIVE STABILITY CONTROL, WASN'T WORKING PROPERLY. WHEN I RECEIVED THE CAR BACK THE TECH SAID THE TRACTION CONTROL IS FIXED AND WORKING FINE. I DIDN'T SEE HOW HE COULD HAVE SAID THAT WHEN THE CAR NEVER LEFT THE SHOP. I REALIZE NOW THAT HE WAS AWARE OF SOMETHING THAT I WASN'T. THE TRACTION WASN'T FIXED, BUT I FELT THAT I CAN'T BRING IT BACK DUE TO INCOMPETENCE. I WENT TO FORUMS AND FOUND PLENTY OF COMPLAINTS FROM OTHERS. THEN I NOTICED THAT 2005-2006 CORVETTES WITH THE RPON37 STEERING COLUMN BUILT IN 2005 WERE RECALLED FOR THIS. NHTSA CAMPAIGN NUMBER WAS 10V172000 AND GM'S CAMPAIGN # WAS N100118. I CALLED GM THEY SAID I AM MISTAKEN MY CAR IS NOT AFFECTED WHICH IS [XXX]. I THEN FOUND FROM THE INTERNET THAT PART #19179794, CLIP, WAS USED TO FIX THE ISSUE. I THEN ORDERED ONE OF THESE AND FOLLOWED THE INSTRUCTIONS TO REPAIR IT AND FOUND THIS CLIP WAS INSTALLED, BUT IMPROPERLY HENCE THE REASON IT WASN'T FIXED BY THE TECH, BUT HE WAS UNDER THE IMPRESSION IT WAS SOLVED. I THEN REPLACED THE CLIP PROPERLY AND NOW IT'S OK. GM WAS VERY DIFFICULT AND DISMISSIVE DURING THE ENTIRE ORDEAL. LOOKING ON YOUR WEB SITE IT SPECIFICALLY STATES THAT MY VIN # DOES IN FACT FALL INTO THE SPECS OF YOUR RECALL. I AM GOING TO ENCLOSE A PHOTO OF THE BENT, IMPROPERLY, INSTALLED CLIP AND A PROPER PICTURE OF THE CLIP. ALSO THE HARNESS THAT NEEDS THE CLIP TO SHOW THAT THE BENT PRONG IS NEEDED TO REPAIR THE HARNESS. PARTS OF THIS DOCUMENT HAVE BEEN REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
I RECENTLY HAD MY VALVES TESTED BY A LOCAL SHOP SINCE IVE HEARD FROM OTHER OWNERS THAT THE LS7 VALVES DROP AT ANY GIVEN TIME. I HAD TWO VALVES OUT OF SPECS AND HAVE TO GET IT FIXED IN ORDER TO SAVE ENGINE FROM FUTURE DAMAGE. MY CAR CURRENTLY HAS 52,241 MILES.
I HAD A FRIEND WHO HAD AN ENGINE FAILURE ON THIS SAME ENGINE DUE TO A FAILED EXHAUST VALVE. THE VALVE GUIDES WERE EXTREMELY WORN ON HIS CAR CAUSING THE VALVE FAILURE. DUE TO HIS FAILURE AND MANY OTHERS LIKE IT, I REMOVED MY HEADS AND INSPECTED. SURE ENOUGH, THEY WERE SIGNIFICANTLY BEYOND GENERAL MOTORS PUBLISHED TOLERANCES AND REQUIRED MACHINING TO REPAIR. THIS WAS AT SIGNIFICANT COST TO ME AND OUT OF POCKET. GM KNOWS OF THIS ISSUE AND REFUSES TO PARTICIPATE IN REPAIR COSTS FOR CARS OUT OF WARRANTY EVEN THOUGH IT'S A DESIGN FLAW AND SAFETY CONCERN. IF AND WHEN THE VALVE CATASTROPHICALLY FAILS, THE ENGINE WILL HAVE A COMPLETE SHUT DOWN, LARGE AMOUNTS OF SMOKE OUT THE EXHAUST CLOUDING THE OTHER DRIVERS VISION, AND HAS THE POSSIBILITY OF LEAVING OIL SLICKS ON THE ROAD SURFACE. *TR
VALVE GUIDES OUT OF WEAR WITH POSSIBLE FAILURE INCLUDING VALVE TO DROP INSIDE COMBUSTION CHAMBER
I WAS INTERNING THE INTERSTATE 15 IN CALIFORNIA AND WAS PICKING UP SPEED TO INTER THE HWY AND MY CORVETTE Z06 STARTING MAKING A KNOCKING SOUND AND LOST POWER AND I TURNED IT OFF AND HAD IT LOOKED AT MY A VERY WELL KNOW AUTOMOTIVE SHOP WHO SPECIALIZES IN GM VEHICLES. THEY TOLD ME IT DROP AN EXHAUST VALVE.
I WAS CONCERNED ABOUT A NOISE THAT I WAS HEARING IN MY 2006 Z06 THAT IS UNLIKE ANY OTHER NOISE I HAVE HEARD WHILE CURRENTLY OWNING MY THREE OTHER GM VEHICLES. I DECIDED TO BRING IT TO A WELL KNOW CORVETTE SPECIALITY SHOP NEAR ME. THE TOLD ME ABOUT THE VALVE GUIDE ISSUE THAT HAS BEEN LINKED TO THE LS7 HEADS. I IMMEDIATELY TOLD HIM TO TAKE THE HEADS OFF THE CAR AND CHECK THEM. I HAD 4 EXHAUST VALVES THAT WERE WAY OUT OF GM SPECS. I HAD THE HEADS RE-MACHINED PROPERLY AND INSTALLED NEW INTAKE AND EXHAUST VALVE GUIDES, VALVE SPRINGS AND SEALS.
AIRBAG DISABLED LIGHT COMES ON UNDER NORMAL DRIVING CONDITIONS. SOMETIMES GOES OUT AFTER RESTART.
DRIVING ON THE FREEWAY AT APPROX. 65 MPH. , THE STEERING WHEEL ON MY CAR " TOOK CONTROL OF ITSELF AND JERKED TO THE LEFT: ON THE DASH POD IT STATED " SERVICE ACTIVE HANDLING SYSTEM" . I PULLED THE CAR OVER AS SOON AS I COULD DO SO SAFELY AND SHUT THE CAR OFF. AFTER RESTARTING IT THE WARNING WENT AWAY AND THE STEERING RETURNED TO NORMAL.
VEHICLE HAS A CONSTANT AIRBAG INDICATOR ILLUMINATED. AIRBAGS HAVE NEVER BEEN DEPLOYED.
I WAS DRIVING DOWN A BUSY STREET AT 35 MPH IN HEAVY TRAFFIC AND HEARD A METALLIC SOUND. THE ENGINE LOCKED UP AND THE REAR END SKIDDED TILL I PUT IN THE CLUTCH AND COASTED TO A PARKING LOT. I WAS AWARE OF THE VALVE PROBLEMS SO I TOOK THE HEAD OFF THE ENGINE AND SURE ENOUGH DROPPED A VALVE TAKING OUT THE PISTON AND BREAKING THE BLOCK. I TOOK THE CAR TO KOOL CHEVY AND WAS TOLD IN WOULD COST 22,000 DOLLARS TO FIX IT. KOOL TOLD ME GM WOULD NOT COVER ANY OF IT BECAUSE THE CAR WAS OUT OF WARRANTY AT 59,000 MILE ON THE CAR. I COULD NOT AFFORD TO FIX THE CAR SO I SOLD THE CAR AS IS LOSING MORE THAN HALF WHAT THE CAR WAS WORTH. I AM STILL SICK ABOUT THIS A YEAR LATER AS I WILL NEVER BE ABLE TO HAVE ANOTHER CAR LIKE THIS. I FEEL LIKE GM SHOULD HAVE WORKED WITH ME AS THIS WAS A KNOWN PROBLEM WITH THE LS7 ENGINE. IF THIS WOULD HAVE HAPPENED AT HIGHWAY SPEEDS IT WOULD HAVE BEEN A LOT WORSE THAN IT WAS. LOST POWER STEERING, POWER BRAKES, AND SKIDDED WHEN THE ENGINE LOCKED UP.
RARELY, DURING LOW SPEEDS (UNDER 15 MPH), WHILE DRIVING STRAIGHT, THE LEFT REAR WHEEL WILL LOCK UP, INDUCING A HARSH LEFT TURN, UNSTABLE MANEUVERING, AND CAUSING THE MOTOR TO ATTEMPT TO STALL. STEERING IS EXTREMELY UNSTABLE AND VIOLENT AND OPERATOR HAS TO FIGHT AGAINST THE CAR WANTING TO TURN LEFT BY APPLYING EXTREME RIGHT TO THE STEERING WHEEL. THE ONLY REMEDY IS TO ENGAGE AND DISENGAGE THE CLUTCH SEVERAL TIMES UNTIL THE LEFT REAR WHEEL UNLOCKS. SYMPTOMS HAVE NOT OCCURRED DURING NORMAL TRAFFIC SPEEDS (ABOVE 15 MPH). AUTO HANDLING/TRACTION CONTROL AND ABS LIGHTS ARE ACTIVATED DURING THIS EVENT. VEHICLE IS IN FACTORY CONDITION. ONLY EXCEPTION IS ALTERNATE BRAND OF TIRE (NITTO INVOS) - BUT MAINTAINING FACTORY SPECIFICATIONS (FRONT: 275/35ZR18; REAR: 325/30ZR19). HAVE NOT REPORTED TO MANUFACTURER YET (IT IS TOO RANDOM AND RARE TO REPRODUCE ON A PREDICTABLE OCCURRENCE). ENVIRONMENTAL CONDITIONS: NORMAL (SUNNY, DRY PAVED SURFACE).
CRUISING AT 50 MPH ON FEEDER RAMP AND DIC SHOWED ENGINE POWER REDUCED FOR 2 SECONDS THEN BOOM! *TR
I BOUGHT THIS CORVETTE Z06 USED FROM A PRIVATE PARTY. THE ENGINE HAD A CATASTROPHIC FAILURE DUE TO A KNOWN ISSUE WITH THE VALVE GUIDES AND VALVES IN THE LS7 MOTOR FROM THE FACTORY. I WAS DRIVING HOME FROM WORK WHEN THE MOTOR FAILED. I WAS LUCKY TO BE ONLY A MILE FROM HOME WHEN IT FAILED AND I WAS ABLE TO COAST INTO MY GARAGE. THE EXHAUST VALVE DROPPED AND DESTROYED THE #1 PISTON ALONG WITH THAT CYLINDER, AND THE ENGINE BLOCK. NOTHING IN THE MOTOR IS SALVAGEABLE AS IT BENT OR SENT METAL SHARDS INTO EVERY PART OF THE MOTOR. I HAVE TRIED SEVERAL TIMES TO GET CHEVY TO HELP ME WITH THIS MOTOR, BUT THEY WILL NOT HELP AT ALL. THEY KNOW ABOUT THE PROBLEM, BUT WILL NOT LIFT A FINGER TO HELP ANYONE. *TR
MANUFACTURING DEFECTED IN THE LS7 MOTOR. UPON FURTHER INVESTIGATION I HAD MY 2006 CORVETTE Z06 INSPECTED FOR A LOUD AUDIBLE TICK IN THE MOTOR. THE SOURCE OF THIS NOISE WAS FROM THE IN-BALANCE FROM THE #3 AND #4 INTAKE VALVES ON THE ENGINES HEADS. THERE IS PREMATURE WEAR ON BOTH VALVE GUIDES CAUSING INTERNAL FAILURE TO THE MOTOR. UNDER POWER DEMAND THE IN-BALANCE WILL CAUSE THE TITANIUM ROD TO STRIKE THE SIDES OF THE VALVE SEAT CAUSING THE HEAD OF THE VALVE TO CRACK AND FALL INTO THE CYLINDER. ONCE THIS OCCURS INSTANT CATASTROPHIC FAILURE OF THE MOTOR HAPPENS RESULTING IN WHITE BELLOWING SMOKE FROM THE EXHAUST, OIL SPILLAGE, AND ENGINE LOCK RESULTING IN THE VEHICLE SKIDDING OFF THE ROAD OR LOOSING CONTROL. FORTUNATELY FOR ME I CAUGHT THIS IN TIME BEFORE HAVING A CATASTROPHIC FAILURE. BOTH LS7 HEADS ARE BEING REPAIRED AND MACHINED TO MEET INDUSTRY STANDARDS. THIS PROBLEM MUST BE ADDRESSED TO ALL LS7 Z06 OWNERS AS IT COULD AND HAS CAUSED SEVERAL CRASHES AND POSSIBLE DEATHS. ONCE REPAIRS TO THE LS7 HEADS ARE MADE THE VEHICLE CAN BE RETURNED TO SERVICE. *TR
2006 Z06 CORVETTE ENGINE WAS MAKING AN UNUSUAL NOISE. AFTER DOING SOME RESEARCH AND THE FINDING, IT WAS DETERMINED THAT THE VALVETRAIN ON THE ENGINE MAY BE PENDING FAILURE. THE HEADS WERE REMOVED AND VALVE TRAIN TOLERANCE CHECKED TO BE FOUND WAY OUT OF SERVICEABLE LIMITS. THUS REQUIRING REPAIR. THIS WAS CONSIDERED EXCESSIVE WEAR FOR SUCH A LOW MILEAGE VEHICLE THAT WAS PENDING CATASTROPHIC ENGINE FAILURE IF THE REPAIRS TO THE HEADS WAS NOT PERFORMED. IN DOING ADDITIONAL RESEARCH, THIS APPEARS TO BE QUITE COMMON FOR THE Z06'S 7.0L LS7 ENGINE. LUCKILY MY ENGINE DID NOT HAVE A CATASTROPHIC FAILURE BECAUSE I TOOK PREVENTATIVE MEASURES AT MY OWN COST, BUT THIS DESIGN SHOULD BE CONSIDERED A FAILURE AND RECALLED. I WAS NOT GOING TO RISK A CATASTROPHIC ENGINE FAILURE POSSIBLY ON THE HIGHWAY AND PUT MYSELF AND OTHERS AT RISK. PLEASE INVESTIGATE.
DATE OF HEADS PULLED: 7/5/12 HEAD TYPE: GM LS7 YEAR: 2006 MILES: 16,000 TRACK TIME: NONE TUNE: STOCK I HAD MY CYLINDER HEADS REMOVED BECAUSE I WAS PARANOID AFTER READING ONLINE ABOUT MANY OTHER OWNERS HAVING ISSUES WITH THEIR VALVE GUIDES BEING OUT OF SPEC. MY CYLINDER HEADS HAD VALVE GUIDES THAT WERE WAY OUT OF SPEC AND THE CAR ONLY HAD 16,000 MILES ON IT AND WAS NEVER TRACKED OR ABUSED. THESE WERE ON THE VERGE OF HAVING THE VALVE BREAK OFF AND SEIZE THE MOTOR WHICH COULD HAVE RESULTED IN SERIOUS INJURY TO MYSELF AND OTHERS AROUND ME WHILE DRIVING. I PAID OUT OF MY OWN POCKET TO HAVE THESE HEADS REDONE. MAX ALLOWABLE CLEARANCE IS 0.0037 FOR BOTH INTAKE AND EXHAUST. VALVE GUIDE CLEARANCES INTAKE #1 TOP .0027 MID .0021 BOT .0024 INTAKE #2 TOP .0030 MID .0022 BOT .0028 INTAKE #3 TOP .0025 MID .0022 BOT .0023 INTAKE #4 TOP .0030 MID .0023 BOT .0025 INTAKE #5 TOP .0033 MID .0022 BOT .0027 INTAKE #6 TOP .0028 MID .0022 BOT .0025 INTAKE #7 TOP .0029 MID .0023 BOT .0027 INTAKE #8 TOP .0030 MID .0023 BOT .0028 ========================= EXHAUST #1 TOP .0022 MID .0026 BOT .0069 EXHAUST #2 TOP .0022 MID .0024 BOT .0048 EXHAUST #3 TOP .0020 MID .0028 BOT .0064 EXHAUST #4 TOP .0022 MID .0024 BOT .0039 EXHAUST #5 TOP .0021 MID .0029 BOT .0085 EXHAUST #6 TOP .0021 MID .0023 BOT .0046 EXHAUST #7 TOP .0021 MID .0024 BOT .0054 EXHAUST #8 TOP .0022 MID .0025 BOT .0033. *TR
MY SON WAS DRIVING AND JUST COMPLETED A TURN WHEN HE APPLIED THE ACCELERATOR AND THE ENGINE STOPPED ABRUPTLY. THERE WAS A CLOUD OF SMOKE AND THEN A SMALL FIRE UNDERNEATH THE CAR FROM THE OIL THAT CAME OUT FROM A BASEBALL SIZE HOLE IN THE SIDE OF THE BLOCK BELOW THE NUMBER 8 CYLINDER. UPON FURTHER INVESTIGATION, A VALVE IN THE NUMBER 8 CYLINDER SNAPPED BELOW THE VALVE GUIDE DROPPING THE HEAD OF THE VALVE ONTO THE PISTON WHICH CAUSED THE FAILURE. I HAVE THE ENGINE AVAILABLE FOR INSPECTION. *TR
HELLO, I AM REPORTING ON MY 2006 C6Z06 CORVETTE THAT RECENTLY HAD THE VALVE-TO-GUIDE CLEARANCES CHECKED ON MY ENGINE AND MY MEASUREMENTS ARE BEYOND THE SERVICEABLE SPECIFICATIONS ON 8 OUT OF 16 VALVES, BOTH INTAKE AND EXHAUST. I CONSIDER THIS A SAFETY HAZARD DUE TO THE FACT THAT IF THE VEHICLE IS DRIVEN AND ENGINE SEIZES, LOSS OF CONTROL MAY OCCUR. I ALSO HAVE WHAT APPEARS TO BE A LEAK ON THE FUEL MODULE/SENDING UNIT, SPECIFICALLY ON THE TOP PLASTIC ELBOW CONNECTOR. I HAVE STRONG GASOLINE ODOR IN THE CABIN OF THE CAR AND VISIBLE GASOLINE FROM THE UNDERSIDE OF THE CAR NEAR THE FUEL TANK. *TR
THE CYLINDER HEADS AT 69K MILES WERE CHECKED DUE TO EXCESSIVE VALVE TRAIN NOISE AND THE VALVE GUIDES AND ONE INTAKE VALVE WERE FOUND TO HAVE CLEARANCE MORE THAN DOUBLE THE SERVICE TOLERANCE. *TR
TL* THE CONTACT OWNS A 2006 CHEVROLET CORVETTE Z06. THE CONTACT RECEIVED A RECALL NOTIFICATION FOR NHTSA CAMPAIGN NUMBER: 14V251000 (ELECTRICAL SYSTEM, EXTERIOR LIGHTING). THE DEALER COULD NOT REPAIR THE VEHICLE FOR TWO MONTHS BECAUSE THE PARTS WERE NOT AVAILABLE. THE MANUFACTURER WAS NOTIFIED. THE CONTACT HAD NOT EXPERIENCED A FAILURE.
THIS CAR WAS CONVERTED TO A RACE CAR. THE ACCIDENT OCCURRED AT ROAD ATLANTA BEFORE TURN 10A. THE ACTIVE HANDLING APPARENTLY CAUSED THE RIGHT BRAKES TO ENGAGE CAUSING A CLOCKWISE SNAP SPIN THAT RESULTED IN HITTING THE INSIDE CONCRETE RETAINING WALL. A YOUTUBE VIDEO IS AVAILABLE AT: HTTPS://WWW.YOUTUBE.COM/WATCH?V=--X0TR5G_U8&FEATURE=YOUTU.BE ( THE ACCIDENT OBVIOUSLY OCCURS AT THE END OF THE VIDEO.) *TR
LOW BEAM HEADLIGHTS WENT OUT WITHOUT NOTICE AND WOULD NOT COME ON. WAS DRIVING AT THE TIME THE WENT OUT. I MADE IT HOME USING HIGH BEAMS. LOW BEAMS CAME BACK ON THE NEXT MORNING BUT AFTER MY TESTING THE WOULD GO OUT AFTER APX 15 MINUTES AND WOULD NOT COME BACK ON FOR HOURS. *TR
WHILE DRIVING IN A STRAIGHT LINE AT APPROXIMATELY 65 MPH, THE TRACTION CONTROL SYSTEM STRONGLY APPLIED THE LEFT FRONT BRAKE. THE APPLICATION OF BRAKE WAS SUDDEN AND VERY STRONG, NEARLY CAUSING A LOSS OF CONTROL. *TR
Higher-selling and older vehicles accumulate more reports. Counts are not failure rates and are not directly comparable between vehicles that sold in very different numbers.
Categories with enough reports to have a page of their own
Data on this page last refreshed .