2024 GMC Yukon Xl Problems

On September 17, 2026, at approximately 22,861 miles, the 6.2L L87 V8 engine in my 2024 GMC Yukon XL suffered a sudden loss of propulsion and was subsequently confirmed by an authorized GMC dealer to be seized and require complete replacement. I was entering northbound I-75 from the Mt. Paran Road entrance in Atlanta, GA with two of my children in the vehicle. This entrance has an extended acceleration ramp where vehicles accelerate to interstate merging speed. While accelerating, the engine briefly stuttered and then the vehicle stopped producing power when I pressed the accelerator. I was unable to continue accelerating and moved onto the limited shoulder. Other vehicles continued accelerating toward I-75 and passed immediately adjacent to us at significant speed. My children and I remained stranded there for approximately two hours waiting for a tow. The vehicle was towed to an authorized GMC dealer, which confirmed the engine is seized and requires complete replacement. The vehicle and failed engine are currently at the dealer and available for inspection. This vehicle was previously subject to NHTSA Recall 25V-274 / GM N252494000 for L87 engine failure and loss of propulsion. An authorized GMC dealer completed the recall procedure on November 3, 2025. The engine was not replaced; it passed the prescribed inspection and received the higher-viscosity-oil remedy. Despite completion of the recall procedure, the engine subsequently experienced the loss-of-propulsion condition identified by the recall. I understand NHTSA has investigated L87 engine failures occurring after completion of this recall remedy, including RQ26001 and EA26005. I am reporting this post-remedy failure because it may be relevant to that investigation.

Update to original claim filed 11760897. Dealership inspected on 9/9/2026 and found engine damage severe enough to warrant a complete replacement. Catastrophic damage. Unspecified what caused the damage, but service advisor made me aware of a deep gash along the cylinder wall after removing the cylinder heads, unspecified cylinder. Likely from cylinder 3 where the code was being displayed- P0303. Vehicle was in the beginning stages of an oil consumption test and had a history of oil loss without any visible leaks. Add oil light came on 650 miles after oil change. Oil was likely being burnt up through combustion due to damaged cylinder wall. Unknown time for new engine to be installed. Estimated backlog 600 engines, could be regionally or nationally. Replacing engine at 29,800 miles, however vehicle has been having these issues much longer- closer to 20,000 miles. I want consumers to be aware this vehicle was not part of the national recall. Vehicle was manufactured in July 2024, two months past the recall date established for these GM engines.

Cameras go black and become inop randomly. Been in shop multiple times for concern. Software updates have been performed, modules replaced, cables, and now it’s back for the same concern.

First incident April 9 2024 not even a month after purchased. Vehicle dashboard lit up light a Christmas tree all warning lights while driving on highway. Vehicle shook and sputtered and turned off. The vehicle was serviced explanation given was loose spark plugs on a new vehicle. 2nd incident roughly month after recall repair for engine propulsion campaign. February 26 and 27 2026 . While driving the following lights came on Engine failure ,Brake failure , Service Transmission now unable to shift soon. I was terrified because I could not control the vehicle. I had the vehicle towed to the dealership. The answer to the issues was Battery failure. Third incident April 17th 2026 I driving on highway 70 miles check engine light comes on flashes dashboard goes dark. Vechicle sputters and shut down. I restarted the vehicle the warning on the display disappeared and the vehicle restarted. I reached returned the vehicle again to the dealership because the problem resumed slowing down even though I’m depressing the gas. Vehicle is shifting and dragging. Resulting unexpected lurching. My vehicle has been at the dealership since end of April 2026 it remains there currently. My representative stated a code indicating misfiring has appeared 18 times. Also everyday my vehicle keeps saying software update even I installed the update and it says complete. I know GM is not updating my vehicle software everyday. That indicates there is a computer issue as well. My anxiety level is through the roof at this point. I complained before about this same failures in a Cadillac Escalade prior to it lurching forward and crashing. I filed a complaint before February 2024 . There is something really wrong with GM engines and software. I know I’m not the only one experiencing these problems

On September 17, 2026, at approximately 22,861 miles, the 6.2L L87 V8 engine in my 2024 GMC Yukon XL suffered a sudden loss of propulsion and was subsequently confirmed by an authorized GMC dealer to be seized and require complete replacement. I was entering northbound I-75 from the Mt. Paran Road entrance in Atlanta, GA with two of my children in the vehicle. This entrance has an extended acceleration ramp where vehicles accelerate to interstate merging speed. While accelerating, the engine briefly stuttered and then the vehicle stopped producing power when I pressed the accelerator. I was unable to continue accelerating and moved onto the limited shoulder. Other vehicles continued accelerating toward I-75 and passed immediately adjacent to us at significant speed. My children and I remained stranded there for approximately two hours waiting for a tow. The vehicle was towed to an authorized GMC dealer, which confirmed the engine is seized and requires complete replacement. The vehicle and failed engine are currently at the dealer and available for inspection. This vehicle was previously subject to NHTSA Recall 25V-274 / GM N252494000 for L87 engine failure and loss of propulsion. An authorized GMC dealer completed the recall procedure on November 3, 2025. The engine was not replaced; it passed the prescribed inspection and received the higher-viscosity-oil remedy. Despite completion of the recall procedure, the engine subsequently experienced the loss-of-propulsion condition identified by the recall. I understand NHTSA has investigated L87 engine failures occurring after completion of this recall remedy, including RQ26001 and EA26005. I am reporting this post-remedy failure because it may be relevant to that investigation.

1.XXX XX— GM Recall Notification (Recall No. N252494000) I received official notification from General Motors of Recall N252494000 affecting my vehicle. I brought the vehicle to [XXX] as directed to have the recall remedy performed. 2. XXX — First Report of Engine Propulsion Issues I reported engine propulsion concerns to Jim Ellis. This was my first formal complaint regarding the performance of the vehicle following the recall remedy. 3. XXX — Oil Type Change Performed by Jim Ellis Jim Ellis performed an engine oil type change, switching to 0W-40 oil, and advised me that this change would serve as the fix for Recall N252494000. I accepted this remedy in good faith. 4. XXX — Low Oil Warning Light Activated Approximately nine months after the recall remedy, and well before the end of the recommended oil life cycle, the low oil warning light activated on my dashboard. This is abnormal and indicative of excessive oil consumption. I returned to Jim Ellis, who performed a fresh oil change and placed my vehicle on a 6,000-mile oil consumption test — an acknowledgment that an oil consumption problem exists. 5. XXX — Active Engine Misfires, Jerking, and Flashing Check Engine Light While operating my vehicle on Sunday, May 31, 2026, I experienced severe engine jerking and misfires. The check engine light began flashing — not steady — which I understand to indicate an active and serious engine misfire event. I was genuinely concerned for my personal safety and immediately parked the vehicle. It has not been driven since. 6. XXX — GM Corporate Case Opened I contacted GM Customer Care and was assigned Corporate Case Number INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

On September 17, 2026, at approximately 22,861 miles, the 6.2L L87 V8 engine in my 2024 GMC Yukon XL suffered a sudden loss of propulsion and was subsequently confirmed by an authorized GMC dealer to be seized and require complete replacement. I was entering northbound I-75 from the Mt. Paran Road entrance in Atlanta, GA with two of my children in the vehicle. This entrance has an extended acceleration ramp where vehicles accelerate to interstate merging speed. While accelerating, the engine briefly stuttered and then the vehicle stopped producing power when I pressed the accelerator. I was unable to continue accelerating and moved onto the limited shoulder. Other vehicles continued accelerating toward I-75 and passed immediately adjacent to us at significant speed. My children and I remained stranded there for approximately two hours waiting for a tow. The vehicle was towed to an authorized GMC dealer, which confirmed the engine is seized and requires complete replacement. The vehicle and failed engine are currently at the dealer and available for inspection. This vehicle was previously subject to NHTSA Recall 25V-274 / GM N252494000 for L87 engine failure and loss of propulsion. An authorized GMC dealer completed the recall procedure on November 3, 2025. The engine was not replaced; it passed the prescribed inspection and received the higher-viscosity-oil remedy. Despite completion of the recall procedure, the engine subsequently experienced the loss-of-propulsion condition identified by the recall. I understand NHTSA has investigated L87 engine failures occurring after completion of this recall remedy, including RQ26001 and EA26005. I am reporting this post-remedy failure because it may be relevant to that investigation.

6/16 Vehicle issues while driving home from work. Rough idle, multiple check engine lights coming on, Multiple warnings display on dashboard. Vehicle in limp mode from work to home. 6/20 While driving in Roanoke rough idle began. Vehicle check engine light appeared, limp mode only lasted for less than 30 seconds before it went back to normal. 6/23 Vehicle issues began again while driving to work. Pulled into parking lot, turned vehicle off and restarted. Vehicle seemed back to normal. Made appointment through GMC App for first available on 6/29. Leaving work vehicle check engine lights came on again and went into limp mode. 26,764 miles. Drove straight over to Hart GMC (2 miles away) and dropped it off. 6/30 Picked up Vehicle at Hart GMC. Miss fire on cylinder #3. Replaced spark plug #3 and cleared all dtcs codes. 8/6 Oil Change with Consumption Test started 29,072 miles 8/28 Engine Oil Low-Add Oil alarm. Instructed by dealer to not tamper with Test. Must drive 2000 miles before returning vehicle to validate consumption test. 29,728 miles 8/30 Pulling into drive way rough idle began. Vehicle check engine light appeared, limp mode, multiple lights. Scanned with OBD2 scanner- P0303 code. Misfire cylinder 3. 8/31 Vehicle towed from home to Hart motors 29,860 miles. Scanned by service showing P0300 codes along with other codes. I have documented all events with this engine since owning. Concerned the engine would run out of oil before validating consumption test (2000 miles). Dealer told me to keep driving even if it says add oil. Engine historically 2 qts low when add oil warning flashes.

Driving on highway at 80 MPH and accelerator stopped working and car turned off. We had to coast off toll rd and hope for the best. No warning and happened with our whole family in the car. I had a recall notice from manufacturer but last time I tried contacting manufacturer/dealer they said no resolution was available to repair recall yet and that I couldn’t drop off my vehicle.

This is a Post-Remedy Failure of Recall 25V-274 (GMC 6.2L L87 Engine). Following a full engine replacement performed by the dealer under this safety recall, the vehicle has suffered a catastrophic electrical compromise. The vehicle is currently throwing codes P2534 (Low Ignition Voltage) and U3018 (BCM Communication). Safety Hazards: The vehicle experiences sudden loss of power, engine stalling at highway speeds, and total failure of the exterior turn signals (hyper-flash). The AC system has been disabled by the Body Control Module due to low voltage, creating a hazard in high temperatures. This vehicle fits the exact profile of NHTSA Recall Query RQ26-001 and Engineering Analysis EA25-007. The manufacturer's remedy for the safety recall has failed to restore the vehicle to a safe operating condition, and the dealership is attempting to charge diagnostic fees to investigate their own defective recall workmanship.

About 4 weeks ago my vehicle began shaking uncontrollably while driving. The check engine light illuminated and multiple warnings appeared including emissions system, variable valve timing system, engine and transmission failures shown on the GMC app. I contacted the selling dealership and was given an appointment 4 days later. Later that day I drove less than 5 miles to pick up my children from school. During that drive the vehicle filled with a strong gasoline odor and exhaust fumes were overwhelming. I feared the vehicle could catch fire. I contacted the dealership again, stated the vehicle was unsafe, dropped it off at approximately 8:00 PM and was required to obtain my own rental vehicle. After one week I was told the engine required a camshaft and lifter replacement. Inspected & approved by extended warranty, parts were ordered and installed. I retrieved the vehicle on 23 days after the initial failure. The following morning (24th day) while driving approximately 75 mph on a major interstate with my children the vehicle suddenly shifted into neutral and would not re-engage. I was unable to shift into any gear and coasted to a narrow shoulder inches from traffic and guardrail.The dashboard stated the vehicle could not shift into gear and instructed me to push the start button. The engine would not restart. We were stranded approximately two hours in 10-degree weather on a major interstate with heavy semi-truck traffic. Roadside assistance was required. 3 days later the dealership stated the failure was a fuse block. After replacement the vehicle was test driven and stated to be operating normally. A second dealership employee test drove the vehicle, it died again and had to be towed back to the dealership. The battery was replaced after draining while disabled. Repeated mechanical and electrical failures resulted in complete loss of power at highway speeds and placed my children and me in immediate danger. I no longer believe this vehicle is safe to operate.

ChatGPT said: There is a design flaw with the automatic light function. When you turn the knob to disable the automatic lights to avoid blinding someone while parked, the knob returns to the auto position as expected. This is a good system to ensure that the next time you start the car, the lights are in auto again. The issue is with the way the system indicates what is happening to the driver. When the lights are set to auto, the “auto” indicator on the knob is illuminated. If you turn the knob to running lights or full lights, the corresponding indicator lights up as expected. However, when you turn the lights off, the indicator light returns to “auto” even though the lights are actually off. While the physical knob should return to auto to make sure the system resets properly at the next startup, the indicator should switch to the “off” position so the driver knows the lights are off. I drove off in the city and assumed my lights were on because the knob said auto, but I later realized they were off. This creates a serious safety hazard. There is no way to know in that situation if your lights are actually on by looking at the knob unless you cycle the lights again. A recall should be issued to change the software or replace the button to make sure that this is clear to the driver.

Windshield needs replacement – one side window installed incorrectly (huge gap) •Trim peeling (inside and outside) •Heavy rust in engine area •Sunroof seals need replacement •All window tints need replacement •Headlights not aligned – need new ones •Taillights not aligned – need new ones •Spoiler damaged – needs replacement •Dashboard feels loose – needs replacement •Door panel misaligned •Rubber gaskets/seals smushed •Seat covers smushed (from dealer) •Paint peeling (sunroof, edges near wheels) •Plastic components worn / damaged •Front bumper misaligned •Two front fenders need replacement •Tow hitch cover needs replacement •Cargo protector installed on exterior trunk sill •Check engine / transmission alert showed in app (vehicle displayed “check 4x4” while driving) •Bluetooth system not working Everything on this car is not aligned this is a huge safety hazard on everything electrical,engine,visibility they won’t take responsibility they said they don’t have no update on recall it’s 7 months and the NHSTA all won’t take responsibility I contacted them multiple times they just say contact GM for recall info 7 months

Check Engine and transmission alerts appeared in the app; vehicle showed “Check 4x4” while driving, cleared next day •Engine not sounding normal •Paint peeling •Fading plastic trim •Front bumper misaligned •Rear bumper misaligned •Loose front door frames •Marker lights collecting bugs •Plastic becoming loose at the rear hatch •Plastic near auto steps: one side has gaps, the other side fits properly •PPF (paint protection film) peeling •Taillights movable by hand •Fog lights movable by hand •Rear spoiler, hatch glass, and surrounding trim loose/movable •Cargo protector loose on exterior trunk sill •Cracking turn signal stalk •Rust developing within the first year •Finger can fit into gaps at door frames •Exhaust tips showing burnt discoloration •Significant loss of vehicle value: ~$70,000 down from $100,000 at purchase

I am filing this complaint regarding a serious and ongoing safety issue with my GMC Yukon Denali that began with a complete engine failure while driving on the highway with my entire family in the vehicle. While driving at highway speed (about 60–70 mph), the vehicle suddenly lost power and shifted into neutral on its own. While still moving, I tried multiple times to shift back into Drive so I could safely get off the road, but it would not engage. I was only able to coast partially onto the shoulder before the vehicle came to a complete stop, still partly exposed to traffic. The engine shut off and would not restart at all. It would not go into Drive or Neutral, and the vehicle was completely dead. And it had to be towed. The dealer later told me the engine had failed and that a new engine was installed. About a week later, I picked the vehicle up. Less than 20 minutes after leaving the dealership and getting back on the highway, smoke started coming from the vehicle and warnings appeared, messages that the engine was overheating and that I needed to stop the engine immediately. The vehicle was not drivable again and had to be towed back. I again had to arrange transportation home. A few days later, I picked the vehicle up again. Since then, I have had serious four-wheel-drive and drivetrain issues. The vehicle became stuck in 4 Low and I could not get it out for over a day. When it finally came out, the drive mode buttons stopped working correctly. Selecting 2 High sometimes puts it into 4 High, selecting Auto puts it into 2 High, and Auto mode no longer appears. Even when it shows 4 High, the steering is restricted cannot steer 100% to the right or left and the vehicle binds, pops, and jumps when turning. I believe this vehicle is unsafe and poses a serious risk.

My vehicle stalled while driving on a busy highway & I had no option but to pull over, which left me & my family in a very dangerous position. Had to remove my daughter's wheelchair onto a tow truck as the vehicle had no power to use the hoist for her powerchair. Again, on the side of a busy road! Towed the vehicle to a GM dealership, who stated there was catastrophic engine failure & the engine had to be replaced. Had no way to transport my daughter until I got a new engine since her hoist was stuck at the dealership.

6/16 Vehicle issues while driving home from work. Rough idle, multiple check engine lights coming on, Multiple warnings display on dashboard. Vehicle in limp mode from work to home. 6/20 While driving in Roanoke rough idle began. Vehicle check engine light appeared, limp mode only lasted for less than 30 seconds before it went back to normal. 6/23 Vehicle issues began again while driving to work. Pulled into parking lot, turned vehicle off and restarted. Vehicle seemed back to normal. Made appointment through GMC App for first available on 6/29. Leaving work vehicle check engine lights came on again and went into limp mode. 26,764 miles. Drove straight over to Hart GMC (2 miles away) and dropped it off. 6/30 Picked up Vehicle at Hart GMC. Miss fire on cylinder #3. Replaced spark plug #3 and cleared all dtcs codes. 8/6 Oil Change with Consumption Test started 29,072 miles 8/28 Engine Oil Low-Add Oil alarm. Instructed by dealer to not tamper with Test. Must drive 2000 miles before returning vehicle to validate consumption test. 29,728 miles 8/30 Pulling into drive way rough idle began. Vehicle check engine light appeared, limp mode, multiple lights. Scanned with OBD2 scanner- P0303 code. Misfire cylinder 3. 8/31 Vehicle towed from home to Hart motors 29,860 miles. Scanned by service showing P0300 codes along with other codes. I have documented all events with this engine since owning. Concerned the engine would run out of oil before validating consumption test (2000 miles). Dealer told me to keep driving even if it says add oil. Engine historically 2 qts low when add oil warning flashes.

I am filing this complaint regarding a serious and ongoing safety issue with my GMC Yukon Denali that began with a complete engine failure while driving on the highway with my entire family in the vehicle. While driving at highway speed (about 60–70 mph), the vehicle suddenly lost power and shifted into neutral on its own. While still moving, I tried multiple times to shift back into Drive so I could safely get off the road, but it would not engage. I was only able to coast partially onto the shoulder before the vehicle came to a complete stop, still partly exposed to traffic. The engine shut off and would not restart at all. It would not go into Drive or Neutral, and the vehicle was completely dead. And it had to be towed. The dealer later told me the engine had failed and that a new engine was installed. About a week later, I picked the vehicle up. Less than 20 minutes after leaving the dealership and getting back on the highway, smoke started coming from the vehicle and warnings appeared, messages that the engine was overheating and that I needed to stop the engine immediately. The vehicle was not drivable again and had to be towed back. I again had to arrange transportation home. A few days later, I picked the vehicle up again. Since then, I have had serious four-wheel-drive and drivetrain issues. The vehicle became stuck in 4 Low and I could not get it out for over a day. When it finally came out, the drive mode buttons stopped working correctly. Selecting 2 High sometimes puts it into 4 High, selecting Auto puts it into 2 High, and Auto mode no longer appears. Even when it shows 4 High, the steering is restricted cannot steer 100% to the right or left and the vehicle binds, pops, and jumps when turning. I believe this vehicle is unsafe and poses a serious risk.

Vehicle was operating on the interstate with cruise control activated. Time was approximately 9:15pm. Weather was fair with temperatures in the lower 60's. Speed was approximately 73mph. Without any audible or warning light notifications the engine stalled and all exterior lighting, power assisted braking and steering was lost. The emergency flashers were immediately activated to warn vehicles in nearby proximity of our emergency status. I tried to restart the engine(the transmission was showing to be in N)with no success. During the attempt to restart, the exterior lighting was restored. With the path of travel now visible, I was able to slow the vehicle to a safe speed and exit from the roadway onto the shoulder. Upon stopping, the vehicle was placed into P and OnStar was notified of the event. We remained in the vehicle until one of our friends was able to take us home. Onstar contacted AAA to remove the vehicle to the nearest GM dealership.

The contact owns a 2024 GMC Yukon XL. The contact stated while driving approximately 65 MPH, there was an abnormal bang coming from the vehicle and the contact became aware that the front section of the sunroof had exploded. The contact stated that there was no other vehicle nearby. The contact stated that the sunroof sprayed glass fragments onto the instrument cluster, front seats, and rear seats. The contact had taken the vehicle to a local dealer, where it was diagnosed and determined that the sunroof glass needed to be replaced. The vehicle was being repaired. The manufacturer was not informed of the failure. The failure mileage was approximately 8,000.