2025 GMC Yukon Problems

GM performed a vehicle wide Over the Air reprogramming of the modules incorporated in the VIP/Global B electronics platform in April, 2026. Following that my vehicle became totally dead. Key fob would not unlock the vehicle. Had to use the metal key, open the drivers door. Opened the door, nothing moved. No lights, no movement from anything on the vehicle. Opened the hood, charged the battery and tried to crank it. Would not budge. Starter would not engage. Disconnected the negative battery cable. Tried again. Still would not budge. After an hour of so of trying and using jumper cables from our other vehicle, still would not budge. I disconnected the negative battery cable from the right front fender ground and reattached it. It then cranked. Drove the vehicle 30 miles at interstate speed. 8 miles in city traffic. Drove home and parked it in the garage. Drove it abput 10-12 days later to get breakfast. Parked it, locked it with the key fob. Came back after getting food, key fob would not work. Opened it with the button on the door handle. Got In tried to crank it. Would not budge. Disconnected the negative battery cable twice, before it cranked, but would not drive. Message in dash said vehicle could not be driven. Finally got it cranked. GM never advised that the battery must have a 70% charge at all times for the electronics to work. Owner's manual contains no such statement. Vehicle is defective to the extent that it will leave me stranded in wherever the battery power is less than 70%. Dangerous to get stranded at night on a lonely road or highway, away from cities with tow trucks and competent service personnel. Vehicle in shop 32 days before dealer advised resolution. Modules bricked requiring engine control module and telematics module replacement.

Just over 6k miles, engine failure.

The contact owns a 2025 GMC Yukon. The contact stated that while the vehicle was shifted into reverse, the rear-view camera displayed a black screen. The image in the rear-view camera was not visible, specifically in areas where there were reflective lights. The dealer was contacted and assisted the contact with the brightness options on the rear-view camera and stated there was no failure with the camera. The camera was not repaired or replaced. The manufacturer was made aware of the failure. The failure mileage was approximately 16.

My 2025 GMC Yukon's infotainment system has repeatedly failed. The huge center screen frequently goes black upon starting the car. Once the screen goes black you are unable to control literally dozens of the vehicle's features including but not limited to climate controls, safety features, heated/ventilated seats, gps, lane assist, the radio, no backup camera, etc. When the screen blacks out, the vehicle automatically turns the heat on to 76 degrees every single time and blows hot air from the front windshield defogger vents only. The list of features controlled by the touch screen is quite enormous. I have taken the vehicle to the GMC dealer four (4) times for software updates, none of which solved the problem and they have admitted they have no fix for this issue. The issue is widespread, as I have encountered literally hundreds of owners online like myself dealing with the very same problem; brand new cars that just do not work. GMC has done absolutely nothing to get to the bottom of this.

The progressive failure of the factory steering wheel adhesive on my 2025 GMC Yukon creates an immediate, active safety hazard during vehicle operation. The material failure and sticky glue are localized directly around the integrated heating element of the steering wheel. This failure severely impacts driving maneuvers as well as a potential electrical fire hazard. The liquefied glue residue is incredibly sticky and continually transfers to the driver’s hands, resulting in a compromised, slippery grip on the steering wheel. During active driving maneuvers, such as hand-over-hand turning, navigating sharp curves, the loose edges of the peeling leather and separating trim physically catch on the driver's palms. This restricts smooth wheel rotation, disrupts natural hand movement, and threatens a sudden, temporary loss of steering control. This manufacturing defect introduces severe driver distraction and physical interference with critical steering components while driving, compounded by a potential thermal or electrical defect in the steering wheel heating assembly.

GM performed a vehicle wide Over the Air reprogramming of the modules incorporated in the VIP/Global B electronics platform in April, 2026. Following that my vehicle became totally dead. Key fob would not unlock the vehicle. Had to use the metal key, open the drivers door. Opened the door, nothing moved. No lights, no movement from anything on the vehicle. Opened the hood, charged the battery and tried to crank it. Would not budge. Starter would not engage. Disconnected the negative battery cable. Tried again. Still would not budge. After an hour of so of trying and using jumper cables from our other vehicle, still would not budge. I disconnected the negative battery cable from the right front fender ground and reattached it. It then cranked. Drove the vehicle 30 miles at interstate speed. 8 miles in city traffic. Drove home and parked it in the garage. Drove it abput 10-12 days later to get breakfast. Parked it, locked it with the key fob. Came back after getting food, key fob would not work. Opened it with the button on the door handle. Got In tried to crank it. Would not budge. Disconnected the negative battery cable twice, before it cranked, but would not drive. Message in dash said vehicle could not be driven. Finally got it cranked. GM never advised that the battery must have a 70% charge at all times for the electronics to work. Owner's manual contains no such statement. Vehicle is defective to the extent that it will leave me stranded in wherever the battery power is less than 70%. Dangerous to get stranded at night on a lonely road or highway, away from cities with tow trucks and competent service personnel. Vehicle in shop 32 days before dealer advised resolution. Modules bricked requiring engine control module and telematics module replacement.

GM performed a vehicle wide Over the Air reprogramming of the modules incorporated in the VIP/Global B electronics platform in April, 2026. Following that my vehicle became totally dead. Key fob would not unlock the vehicle. Had to use the metal key, open the drivers door. Opened the door, nothing moved. No lights, no movement from anything on the vehicle. Opened the hood, charged the battery and tried to crank it. Would not budge. Starter would not engage. Disconnected the negative battery cable. Tried again. Still would not budge. After an hour of so of trying and using jumper cables from our other vehicle, still would not budge. I disconnected the negative battery cable from the right front fender ground and reattached it. It then cranked. Drove the vehicle 30 miles at interstate speed. 8 miles in city traffic. Drove home and parked it in the garage. Drove it abput 10-12 days later to get breakfast. Parked it, locked it with the key fob. Came back after getting food, key fob would not work. Opened it with the button on the door handle. Got In tried to crank it. Would not budge. Disconnected the negative battery cable twice, before it cranked, but would not drive. Message in dash said vehicle could not be driven. Finally got it cranked. GM never advised that the battery must have a 70% charge at all times for the electronics to work. Owner's manual contains no such statement. Vehicle is defective to the extent that it will leave me stranded in wherever the battery power is less than 70%. Dangerous to get stranded at night on a lonely road or highway, away from cities with tow trucks and competent service personnel. Vehicle in shop 32 days before dealer advised resolution. Modules bricked requiring engine control module and telematics module replacement.

While driving on a highway, the vehicle intermittently suffers a sudden loss of engine power during acceleration, accompanied by a flashing check engine light. The most serious event occurred while merging into traffic when the vehicle failed to accelerate normally and briefly lost power, creating a risk of being struck by faster-moving vehicles. Pulling over and restarting temporarily restores normal acceleration, but the problem recurs. The malfunction appears consistent with an engine misfire/powertrain fault. An OBD scan has shown misfire-related diagnostic codes (random/multiple misfire and a cylinder-specific misfire). The condition is intermittent and often occurs after approximately 10–45 minutes of driving. The vehicle remains available for inspection. The vehicle has been presented to authorized service departments multiple times. Dealers reported they were unable to duplicate the issue during road testing and no lasting repair has been completed. The manufacturer has been contacted and the vehicle has been evaluated through authorized service channels, but the underlying cause has not been identified. This remains a safety hazard because it reduces acceleration in traffic. Incident list: • 10/25/2025 (~12:25 PM; ~3,108 miles): Loss of power while merging; flashing CEL; restart temporarily resolved. • 10/27/2025–11/04/2025: Intermittent recurrence, usually lasting a few minutes then clearing. • 11/05/2025 (~8:01 AM; ~3,641 miles): Flashing CEL and misfire/loss-of-power symptoms; taken for service. • 11/26/2025 (~10:06 AM): Another episode consistent with the same pattern. • 12/17/2025 (~8:21 AM): Another episode, including during travel to a service visit. • Ongoing: Episodes after ~10–45 minutes; sometimes requires restart to restore drivability. Observed codes: P0300 and P0301. Safety risk: loss of power during acceleration/merging increases risk of rear-end or side-impact collision.

The progressive failure of the factory steering wheel adhesive on my 2025 GMC Yukon creates an immediate, active safety hazard during vehicle operation. The material failure and sticky glue are localized directly around the integrated heating element of the steering wheel. This failure severely impacts driving maneuvers as well as a potential electrical fire hazard. The liquefied glue residue is incredibly sticky and continually transfers to the driver’s hands, resulting in a compromised, slippery grip on the steering wheel. During active driving maneuvers, such as hand-over-hand turning, navigating sharp curves, the loose edges of the peeling leather and separating trim physically catch on the driver's palms. This restricts smooth wheel rotation, disrupts natural hand movement, and threatens a sudden, temporary loss of steering control. This manufacturing defect introduces severe driver distraction and physical interference with critical steering components while driving, compounded by a potential thermal or electrical defect in the steering wheel heating assembly.

This has happened twice. Once in November 2025 and then in January 2026. With super cruise engaged while going around a curve super cruse disengages and the steering wheel turns to driving straight. You have about one or two seconds to take control or crash. This happened while driving about 70 mph on interstate I 70 and next on Ohio 122 going about 45 mph. On I 70 it was a gentle curve and on 122 it was a much sharper curve. Super cruse must give a warning that it about to disengage that is much longer than one or two seconds.

The contact owns a 2025 GMC Yukon. While the contact's husband was driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. The contact stated that the brake failure warning light was illuminated. The contact’s husband depressed the brake pedal and noticed that the brake pedal was firm and difficult to depress. The contact stated that an error message indicated that the vehicle was decelerating. The contact's husband depressed the brake pedal and the vehicle decelerated to 40 MPH. While the contact’s husband was slowly driving into the driveway at the residence, the brake pedal was depressed; however, the vehicle failed to stop. The contact’s husband immediately shifted the gear shifter into park(P) to stop the vehicle. The contact stated that the failure had occurred while on the way home from a family trip. The vehicle was towed to the dealer and the vehicle was diagnosed with a failed brake master cylinder assembly, a failed brake control module, and a failed brake plunger. The contact was informed that the brake master cylinder assembly, the brake control module, and the brake plunger needed to be replaced. The vehicle was not repaired. The contact was informed that the parts were on back-order. The manufacturer was not made aware of the failure. The failure mileage was approximately 3,150.

We purchased a brand new 2025 GMC Yukon on 5/19 and on 5/22, the vehicle would not release the parking brake. Multiple sensors / alerts were displayed, brake assist failure, press hard to brake, speed limited, service ESC, service traction control, check engine light, brake park, service ABS brakes. Vehicle was not drivable. Towed to Marhofer GMC, problem was replicated next day. Was informed that brake booster and master cylinder were bad, however on a national back order. We are now 3 weeks out, without a repair completed or parts. Was also informed by dealer that there is a service bulletin out on this vehicle. Vehicle has 170 miles.

2025 Yukon Denali - Purchased in July of 2025 Specifically to pull air stream trailer. Vehicle Was equipped with necessary tow package for this purpose! #1 problem: Went into limp mode, stopped in traffic, towed to dealer. One week to repair and replace fuel system. ( under 700 Miles ) #2 Problem: Went into limp mode while pulling trailer, vehicle lost all the transmission fluid on ground. In shop sixteen days waiting for new transmission parts. ( Under 700 Miles ) #3 Problem: Vehicle stopped in traffic, towed to dealer where it was determined it needed new engine. In shop Nov 27, 2025, still in shop as of Jan 14, 2026. No ETA on engine or delivery. ( Under 2000 Miles ) #4 Problem: During last failure attempt to use "on star" failed, still not resolved. This vehicle is a danger to the owner and its passengers as well as others when it simply stops working in the middle of a busy highway with a 23' trailer in tow. Not to mention I have $160,000 invested in a car and camper I have yet to be able to use.

Driving through the intersection of N. Scottsdale Road and E. Bell Road in Scottsdale AZ my collision warning red light flashed on the screen and the engine turned off. This caused me to lose forward propulsion and forced me to navigate to the side of the road to avoid being hit by another car. At Van’s GMC, the service manager told me that we experienced a catastrophic engine failure and that the engine seized. Vehicle has been inspected, but I have not received an official diagnostic even though I have requested. There were no warnings or indications that the vehicle was compromised prior to the engine turning off.

On multiple occasions the center screen has been non operational when we start the car and just shows a black screen. The volume knob and screen power button are non-responsive. When this occurs the backup camera is inoperable, which is mandatory safety equipment. the HVAC also cannot be adjusted which could cause a windshield fogging condition which is a safety concern. The vehicle has been to the dealer 3 times for screen problems and the issue has not been resolved. When this occurs the problem persists for a few ignition cycles or for up to a couple of days and then will start functioning again. We have not been able to determine any specific condition that is causing the failure.

Purchased new August 29, 2025 On 12/3/25- Mileage 4495. Took vehicle in for first maintenance service. Tire rotation and oil change. On 1/7/26- Reported grinding noise we had began noticing when starting vehicle. Engine light Service ESC. Service Traction control. Reported to Ben Mynatt GM. On 1/8/26 Mileage 7120- Took Yukon in for service due to grinding noise. Due for 6 module updates and 3 stand alone updates. On 2/16/26 Noticed ticking noise when heat in on high. Scheduled service for 2/26. On 2/24/26 Smell from car, oil reporting low. Dip stick completely dry. Sent email and photos to Ben Mynatt Service. On 2/26/26 Took vehicle in for service. Service advised to start oil consumption test. Ordered blower motor for the squealing noise. Cyl 3 misfire. Was told by the dealer, possibly needs engine 2/27/26 Took Vehicle in for service Check engine light on. Bearing inside blower motor and blower motor replaced. Replaced coil cyl 3 Tire Rotation 2/28/26 Car shaking, smoking, engine light on. Terrible smell from exhaust. Engine light came on, Service ESC, Service Traction Control, Forward Collision Unavailable, Reduced Acceleration Drive with Care Alert. GMC Alert: Service the engine and transmission system immediately alert, Engine Light on. Vehicle Approx miles. Codes misfires to cylinder 3. Took vehicle right to Service Dept. Codes Cleared. Replaced coil on cyl 3 March 7th - Mileage 11,200 Car shaking vigorously! Engine light flashing. Loud knocking coming from vehicle. GMC alert: Service the engine and transmission system immediately alert. Emission system- service now. Engine and Transmission System Service now. Service antilock braking, Stabilitrack stability control systems and airbag system. Service Air Bag System. Emailed to Service March 9th. Took vehicle in. Cylinder 3 & 8 misfire code cold start rough idle code. Oil consumption using approx1 qt of oil/500 miles. Vehicle unsafe risk of engine seizure, fire risk and loss of acceleration is extreme danger