2007 Harley-Davidson Fxsts

THIS ISN'T A COMPLAINT, IT'S AN OBSERVATION. I OWN A HARLEY DAVIDSON THAT HAS A SOLID CAST ALUMINUM REAR WHEEL. THE VALVE STEM IS VISIBLE ON THE RIGHT SIDE OF THE WHEEL AS YOU LOOK TOWARD THE FRONT OF THE BIKE. THIS IS THE SAME SIDE OF THE BIKE THAT THE MUFFLERS AND THE REAR BRAKE DISC ARE MOUNTED. IF A RIDER ATTEMPTS TO PUT AIR IN THE REAR TIRE IMMEDIATELY AFTER STOPPING, THE MUFFLERS ARE VOLCANIC HOT, AND THE REAR DISK IS ALSO QUITE HOT. THE RIDER IS FORCED BY DESIGN OF THE WHEEL TO PUT HIS OR HER HANDS DANGEROUSLY CLOSE TO ITEMS ON THE BIKE THAT ARE HOT ENOUGH TO CAUSE INSTANT 2ND DEGREE BURNS AND IF NOT CAREFUL, 3RD DEGREE. I RECOMMEND THE VALVE STEM ON THIS TYPE OF REAR WHEEL DESIGN, BE MOVED TO STICK THROUGH THE LEFT SIDE OF THE WHEEL WHICH WOULD ELIMINATE THE RIDER FROM HAVING TO NAVIGATE AROUND DANGEROUSLY HOT MUFFLERS AND A BRAKE DISK THAT CAN INSTANTLY BURN HIM OR HER. REAR WHEELS WITH SPOKE DESIGN ARE NOT A PROBLEM, AS THE RIDER HAS THE OPTION OF ATTACKING THE BIKE FROM THE RIGHT OR LEFT. IT SHOULD BE NOTED IN THE OWNERS MANUAL THAT ADDING AIR AFTER AN INITIAL STOP IS NOT RECOMMENDED, BUT IF NECESSARY, USE THE LEFT SIDE OF THE BIKE WHEN ADDING AIR TO A SPOKE DESIGN WHEEL. *TR

NHTSA ID

10390234

Incident

Mar 15, 2011

SERVICE BULLETIN M1684: MARKET SPECIFIC BATTERY INTRODUCTION. PURPOSE: Initial Release. This bulletin informs dealers of the availability of new batteries for new Original Equipment (OE) vehicle production and in the Parts and Accessories (P&A) catalog. Availability of the new Absorbed Glass Mat (AGM) batteries will vary by market and will be transitioning over the next few months. NOTE: The ring terminal screws are not compatible between Leoch and East Penn batteries. The new batteries will include new ring terminal screws, which must be used. The ring terminal screws from the old battery need to be discarded.

SERVICE BULLETIN M1317: NEW BALANCER BEARING REMOVER TOOL HD-48457-A. PURPOSE: The purpose of this bulletin is to inform dealers of an update to the BALANCER SHAFT REMOVER (PART NUMBER: HD-48457). When using these tools to remove the counter balancer assembly, the balance shaft bearing can remain in the crankcase. To remove the bearing without the balance shaft, additional tools were added to the balancer and bearing remover.

SERVICE BULLETIN M1650: MILWAUKEE EIGHT AND TWIN CAM CAMSHAFT DRIVE GEAR RETENTION KIT CHANGES. PURPOSE: This bulletin informs dealers that changes have been made to the Camshaft Drive Gear Retention Kit and service proceduresfor the Milwaukee-Eight and Twin Cam applications. In an effort to increase the clamp load of the camshaft drive sprocket bolted joint and prevent the drive bolt from loosening in high lift camshaft applications, the following changes have been made: a. The camshaft drive bolt final torque has been increased to 40 ft-lbs (54 N·m) for all Milwaukee-Eight and certain Twin Cams models. See Vehicles Affected. This increase in torque will make the bolt a one time use application. Never re-use a camshaft drive bolt for service after tightening to the increased specification. See service manual for updated procedure. b. A new camshaft drive gear retention kit (Part No. 91800088) has been created. This new kit is compatible with all Milwaukee-Eight and Twin Cam engines using Parts and Accessories (P&A) camshaft and Original Equipment (OE) camshaft applications. See Instruction sheet for specific fitment on Twin Cam OE camshaft applications. The new kit utilizes friction washers to prevent unwanted rotation of components in the drive sprocket bolted joint under stress. The use of liquid threadlocker on the threads of the bolt and pre-lube to the head of the bolt flange and outside of the washer help the bolt reach full stretch when tightening. NOTE: Engines produced at all Harley-Davidson Motor Company (HDMC) plants will not come with the new kits installed. They will continue to be produced with (Part No. 25566-06).

SERVICE BULLETIN M1490 (V 24.8.8): DIGITAL TECHNICIAN II - UPDATES AND RELEASE NOTES. PURPOSE: This bulletin informs dealers that Harley-Davidson has made a software update to Digital Technician II (DT II). DIGITAL TECHNICIAN II (PART NUMBER: HD-48650). Version 24.8.8. Release Date: Week of August 5, 2024. New Features for Harley-Davidson vehicles: Advanced Module Replace for 2021 and later Revolution Max; 2023 and later CVO Touring; and 2024 Street Glide (FLHX), Road Glide (FLTRX). New Features for LiveWire vehicles: Updated calibrations for 2024 S2DM EV1/ EV6; 2024 S2MH EV1; and 2024 S2DM, S2MH. Changes: Added Hand Control Module (HCM) (Part No. 71500522A and 71500536A) for reflash support.

GENUINE MOTOR PARTS AND MOTOR ACCESSORIES BULLETIN PAB1158: OIL FILTER PACKAGING AND CASE QUANTITY UPDATE. PURPOSE: To inform dealerships that Harley-Davidson has made updates to oil filters including new part numbers, packaging design, and bulk case quantity changes.

SERVICE BULLETIN M1490 (V 24.6.4): DIGITAL TECHNICIAN II - UPDATES AND RELEASE NOTES. PURPOSE: Revision. This bulletin informs dealers that Harley-Davidson has made a software update to Digital Technician II (DT II). DIGITAL TECHNICIAN II (PART NUMBER: HD-48650). Version 24.6.4. Release Date: Week of May 1, 2024. New Features for LiveWire S2DM and S2MH, 2024 Revolution® Max, and 2024 Touring.