2014 Hyundai Elantra Coupe

The Office of Defects Investigation (ODI) has received eight Hyundai Motor America (Hyundai) and eight Kia America, Inc. (Kia) Part 573 Recall Reports between 2016 and 2023. The combined 16 safety recalls all involve the antilock braking system (ABS) modules or Hydraulic Electronic Control Units (HECU) manufactured by the equipment supplier Mando. The Part 573 Recall Reports contain varying defect descriptions and differing remedy descriptions for the same or similar equipment supplied by Mando. Safety recalls included in this Audit Query (AQ) review include: Hyundai recalls 20V-520, 20V-543, 21V-161, 21V-160, 21V-303, 22V-056, 22V-810, and 23V-651. Kia recalls 16V-815, 20V-518, 20V-519, 21V-137, 21V-331, 22V-051, 22V-800, and 23V-652 The purpose of this AQ is to evaluate the timeliness and scoping of Hyundai and Kia’s defect decision making and adherence with reporting requirements; and understand the varying defect descriptions and remedies between these recalls.

The contact owns a 2014 Hyundai Elantra Coupe. The contact received notification of NHTSA Campaign Number: 23V651000 (Service Brakes, Hydraulic) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

NHTSA ID

11564418

Incident

Sep 22, 2023

The contact owns a 2014 Hyundai Elantra Coupe. The contact received notification of NHTSA Campaign Number: 23V651000 (Service Brakes, Hydraulic) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

NHTSA ID

11561360

Incident

Dec 21, 2023

The National Highway Traffic Safety Administration (NHTSA) has identified the presence of substandard and dangerous driver’s-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

The National Highway Traffic Safety Administration (NHTSA) has issued an urgent safety advisory regarding dangerous, counterfeit driver‑side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or non‑certified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

This TSB references the Op codes to use for claim submission and the Parts required based on the vehicle’s inspection results from TSB 22-01-023H (DTC P1326 – Engine Bearing Inspection/Engine Replacement) or the latest version.

This TSB references the Op codes to use for claim submission and the Parts required based on the vehicle’s inspection results from TSB 22-01-023H-2 (DTC P1326 – Engine Bearing Inspection/Engine Replacement) or the latest version.

This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.