2014 Mercedes-Benz GL63

1. The power steering wheel is stuck at the top position once in a while. 2. Active curve system pump will fail and leak fluids in 30000-40000 miles.

NHTSA ID

11496474

Incident

Jun 15, 2020

THE CAR RAN OUT OF BRAKE FLUID - THERE WAS AN INDICATOR AND WHEN TAKEN TO SERVICE WE WERE TOLD THE RESERVOIR WAS EMPTY. WHAT IS ALARMING IS THAT THE CAR IS SERVICED VERY FREQUENTLY AND ONE SET OF BRAKES WAS RECENTLY REPLACED (ABOUT 6 MONTHS). MOREOVER THE DEALER STATED THERE WAS NO LEAK. THEY STATED THAT THEY DO NOT REPLENISH THE BRAKE FLUID WHEN REPLACING PADS, IN ESSENCE, BECAUSE THE FLUID SYSTEM IS SO FRAGILE AND THEY ARE AFRAID THEY WILL DO MORE HARM THAN GOOD. IT SEEMS LIKE A STRAIGHTFORWARD PROPOSITION THAT IF THE BRAKES ARE CHECKED AND PADS REPLACED FREQUENTLY, AND THERE IS NO LEAK, THERE SHOULD BE NO POSSIBLE WAY FOR THE FLUID TO GO EMPTY ABSENT A DEFECT IN THE CAR (EXCESS FLUID CONSUMPTION FOR SOME REASON BESIDES A LEAK) OR FAULTY MAINTENANCE PROCEDURES. I BELIEVE THE PRACTICE OF NOT REPLENISHING BRAKE FLUID - DESCRIBED TO ME AS THE NORMAL PRACTICE AT MERCEDES SERVICE, NOT A 1-TIME MISTAKE - IS NEGLIGENT. CONTRIBUTING FACTORS INCLUDE (1) MERCEDES BRAKES ARE KNOWN TO WEAR VERY QUICKLY (ROUGHLY ANNUAL BRAKE PAD CHANGE); (2) THE 2014 MODEL ADAPTIVE CRUISE SYSTEM TENDS TO APPLY THE BRAKES VERY OFTEN, I.E. UNINTELLIGENT ALGORITHM THAT USES BRAKES CONTINUALLY WHILE CRUISING AT 70 MPH ON FREEWAY, NOT SOMETHING A HUMAN WOULD EVER DO

NHTSA ID

11143013

Incident

Oct 25, 2018

Mileage

57,000 mi

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time. OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: ‑ Hitting the curb/posts with the front wheels. ‑ Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). ‑ Cracks (1) ‑ High pressure cleaner (2) ‑ Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

Complaint A popup is seen on the HU with the message "data connection temporarily not available". Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.Navigation 7.iHeartRadio 8.Traffic Cams Cause MB Apps is sundowned for all vehicles with NTG4.5 and NTG5 Head Unit Variant. Remedy No support available for NTG4.5 and NTG5 Head Unit Variants for MB App related topics. Note: Please do not create TIPS. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).