2013 Mercedes-Benz GL63

T BONE FRONTAL CRASH IN TARRYTOWN, NY ON 2/5/16 AT 7:59 PM APPROXIMATELY ON ROUTE 119 WEST. VEHICLE # 2 A KIA SUBURBAN MADE A LEFT TURN IN FRONT OF ME WHEN I IN VEHICLE # 1 HAD A GREEN LIGHT AND RIGHT OF WAY. AIR BAGS DID NOT DEPLOY APPROXIMATE SPEED OF MY MB G 63 , 2013 WAS AROUND 35-40 MPH ON ACTUAL POINT OF IMPACT. ROAD SPEED LIMIT WAS 45 MPH. ROADS WERE CLEAR, WEATHER WAS COLD, NO ICE OR RAIN. SEAT BELT RETRACTION ON PASSENGER SIDE CAUSED STERNUM FRACTURE TO THE PASSENGER OCCUPANT. DRIVER SUSTAINED BRUISES ON ARM ON IMPACT. COMPLETE NON DEPLOYMENT OF AIR BAGS IN MY VEHICLE#1 ON IMPACT. CAUSE OF NON DEPLOYMENT BEING INVESTIGATED BY MB FACTORY ENGINEERS- REPORTS WILL BE SHARED WITH YOU ON AVAILABILITY. ## VIN PASSED ## MERCEDES BENZ G63- 2013 ##

NHTSA ID

10837194

Incident

Feb 5, 2016

Mileage

20,000 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint The customer requests deactivation of the N112/9 HERMES communication module Note: Deactivation of the HERMES control unit (N112/9) is not supported for gray-market vehicles. Cause Before deactivating the HERMES control unit (N112/9), it must be clarified by the legal department of the respective MPC whether and under what conditions deactivation may be carried out. If deactivation is not permissible under applicable law, the HERMES control unit (N112/9) must not be deactivated. Remedy Please inform the customer that, following deactivation, the vehicle will no longer be able to place an automatic emergency call, nor will the customer be able to place a manual emergency call. After deactivation, the Mercedes-Benz Digital Extras will also no longer be available. Please have the attached sample form checked by your market's legal department, adapted to local requirements if necessary, and approved. Furthermore, after informing the customer about the effects of deactivation, please have the workshop complete and sign the approved form together with the customer, and send it to the MPC via a TIPS case for audit-compliant documentation. Furthermore, the workshop must affix a sticker to the emergency call button cover on the overhead control panel and to the emergency call button itself. After affixing, pictures of the overhead control panel need to be attached to the TIPS case for audit-proof documentation. After deactivation, the HERMES control unit (N112/9) is in the "Out of Service" operating status, and the display "SOS NOT READY" appears in the Audio/COMAND system. This display message tells the customer that the emergency call function is not available. In detail, the following steps must be carried out 1. The workshop must inform the customer about the effects of deactivation (see above) 2. Legal review by the MPC Legal department to determine whether deactivation is permissible for the vehicle and provision of a market-specific customer form based on the examples (see "Example - Deactivation communication module HERMES customer declaration English V3.0.pdf") 3. Completion of the market-specific customer form by the workshop and obtaining the customer’s signature 4. Creation of a XSS ticket by the workshop for the MPC with the signed customer form attached 5. Written confirmation of legally reviewed and approved deactivation by the MPC in the TIPS case (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, point 1) 6. Creation of an XSS ticket for documentation of the SA code "09o" (zero nine oh) in the Vehicle Documentation System (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, steps 2–7) 7. Ordering of stickers (part number A9078172900), quantity: 2 8. Affixing of the sticker (part number A9078172900) to the cover of the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 9. Affixing of the sticker (part number A9078172900) to the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 10. Taking photos of the applied stickers and attaching them to the TIPS case 11. After the XSS ticket has been successfully processed, the communication module must be deactivated using XENTRY: • Connect XENTRY Diagnosis • Access the HERMES control unit (N112/9) • "Adaptation" tab, menu item "Teach-in processes" -> "Deactivation" • Follow the instructions

Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

Complaint Noises at the front axle when cornering or maneuvering (video files attached) Note: Save video files locally and play them with Windows Media Player. Cause Driving with summer tires in combination with low outside temperatures. At low outside temperatures or in wet conditions, a noise may be produced at the outer wheel on the front axle while maneuvering with sharp steering angles. Note: AMG vehicles with 4MATIC of model series 217 (without code 494) and model series 222 have a modified axle geometry compared with series production vehicles to provide more sporty handling. The problem cannot be remedied by changing the axle settings.