2018 International 4000 Series 4300

PURCHASED JANUARY 25, 2018. WHEN DRIVING FROM LAZYDAYS DEALER IN TAMPA, FL, I HAD TO HOLD THE WHEEL TO THE LEFT TO KEEP THE VEHICLE IN THE LANE. AT THE FIRST REST AREA I PULLED OFF AND SWITCH DRIVERS WITH MY SON JOHN. WHILE FOLLOWING BEHIND I NOTICED IT WAS LEANING TO THE LEFT REAR. AFTER PARKING IT AT OUR STORAGE LOCATION. JOHN REMARKED THAT IT DROVE LIKE AN OLD BOX TRUCK THAT WAS NOT LOADED CORRECTLY. I ATTEMPTED TO CALL THE DEALER DID NOT HAVE CALLS RETURNED. FEBRUARY 19, 2018 DROVE 321 MILES TO FLIMINGO NATIONAL PARK. HAD TO KEEP WHEEL TO LEFT TO GO STRAIGHT WHEN A TRUCK WOULD PASS US THE MOTOR HOME WOULD GO INTO THE RUMBLE STRIPS ON THE RIGHT HAND SIDE. ON THE RETURN TRIP WE STOPPED AT LAZYDAYS TO HAVE IT CHECK OUT. THE SERVICE MANAGER SAID THE NEXT OPEN APPOINTMENT WAS IN THE FIRST WEEK IN APRIL. THEY SUGGESTED THAT I LET IT THERE AND THEY WOULD TAKE TO INTERNATIONAL TO HAVE THE ALIGNMENT CHECKED. WITHOUT ANY OTHER WAY HOME I ELECTED TO DRIVE IT HOME AND THEN TAKE IT TO INTERNATIONAL OF OCALA. AFTER I ARRIVED HOME I LOOKED OVER THE COACH DESIGN AND FOUND THAT IT HAD BEEN BUILT WITH CONSIDERABLY MORE WEIGHT ON THE LEFT THAN THE RIGHT. BOTH SLIDE OUTS, GENERATOR, FRESH WATER TANK, GRAY WATER AND BLACK WATER TANKS FAVOR THE LEFT SIDE. WHEN I CRAWLED UNDER THE COACH I WAS COMPLETELY HORRIFIED. THE FRAME HAD BEN ALTERED FROM THE FACTORY BY A THIRD PARTY. THE WHEELBASE WAS ALTERED BY CUTTING A SECTION OUT OF THE FRAME AHEAD OF THE REAR DRIVE AXLE AND THEN WELDING IT BACK TOGETHER DID NOT FOLLOW THE NAVISTAR INTERNATIONAL BODY BUILDERS HANDBOOK. THE WELDS ARE THE WORST LOOKING WELDS I HAVE EVER SEEN AND CRACKS ARE ALREADY FORMING.

NHTSA ID

11075989

Incident

Feb 22, 2018

Mileage

2,500 mi

This article only applies to Models w/ 0016UZL Built Between 06/23/2014 – 05/11/2020 OR Models w/ 0016UZL w/ Safety Recall 14516 Completed Reference the appropriate Technician Manual for models outside of this population. Safety Recall 14516 has been issued for units built before June 23, 2014. For LT and 2018+ LoneStar: If there is a complaint of the bunk blower turning off after an auto start event, the BCM needs to be updated to Data Version 323 or higher. • The bunk blower turning off was only present in BCM Data Version 309 to Data Version 322 To properly diagnose the system, you must ensure the recall has been performed. Only the "Cold Loop" sealed refrigerant core PN # 2614669C1 is to be replaced when the refrigerant circuit fails. DO NOT REPLACE THE COMPLETE UNIT IF THE A/C IS NOT FUNCTIONING. Complete unit is not Warrantable Refer to the BASIC TROUBLESHOOTING below before replacing any components. This will help you identify which component is at fault or any electrical issues. Refer to PARTS INFORMATION to properly identify the parts that may require replacement The A/C portion of the system is listed below in the parts section. The 16UZL No-Idle HVAC system is designed to disengage when the engine is started, and can be turned on with the key in any position. This battery-powered no-idle HVAC system provides heating and cooling of the sleeper area without use of the vehicle engine. The system is comprised of the no-idle HVAC components located in the sleeper HVAC module, a separate fuel-operated coolant heater mounted under the sleeper, and four additional batteries housed in a second battery box. The no-idle HVAC system shares the air handling assembly and several major components with the truck's standard HVAC system. Most importantly, the shared evaporator core contains refrigerant circuits for both the no idle system and the truck's standard A/C system. With this configuration, some procedures required to service the no idle A/C system will require opening the refrigerant circuit of the truck's standard A/C system. Trucks equipped with the 16UZL No-Idle HVAC system have two separate HVAC systems (Standard Truck A/C and the MaxxPower unit); it is important to identify each clearly, so you are troubleshooting the correct system. Per the Operator's Manual page 10: Run the heater at least once a month during the year (for a minimum of 15 minutes).

New CARB Idle Reduction Change Request

This tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files. It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.

This document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature. Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.

Engine replacements for all International engines will need to follow this procedure.

This document will guide the user through a step-by-step procedure for detecting water leaks in vehicle cabs and windshields using an ultrasonic sound detector.