RoadVitals

2010 Medtec Type Ii (van) Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
Recall campaignsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
2
Newest Feb 14, 2011
Carrying an NHTSA advisoryCampaigns where NHTSA told owners not to drive the vehicle, or to park it outside, until the repair is done.
0
Open investigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0

Recall campaigns

2 campaigns cover this model year — what the defect is, what it could cause, and what the remedy is

11V098000

SEATS

Feb 14, 2011
87 units potentially affected
The defect: MEDTEC IS RECALLING CERTAIN MODEL YEAR 2010 AMBULANCE TYPE II VANS FOR NOT COMPLYING WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 207, "SEATING SYSTEMS," AND FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES." THE REAR FACING AMBULANCE ATTENDANT SEAT UTILIZES A STEEL FLOOR REINFORCEMENT PLATE ON THE BOTTOM SIDE OF THE ALUMINUM FLOOR SUBSTRUCTURE AND THE REINFORCEMENT PLATE WAS OMITTED IN SOME AMBULANCE BODIES.
The risk: IN THE EVENT OF A CRASH, THE SEAT BELT ASSEMBLY ANCHORAGE MAY DISCONNECT FROM THE FLOOR CAUSING THE ASSEMBLY TO FAIL TO RESTRAIN THE SEAT OCCUPANT INCREASING THE RISK OF INJURY TO THAT OCCUPANT.
The remedy: DEALERS WILL INSTALL THE MISSING REINFORCEMENT PLATE UNDER THE FLOOR SUBSTRUCTURE FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING MARCH 2011. OWNERS MAY CONTACT MEDTEC TOLL-FREE AT 1-866-263-3832.
MEDTEC AMBULANCE CORPORATIONManufacturer number 11.03View on NHTSA.gov
10V511000

SEAT BELTS

Oct 19, 2010
198 units potentially affected
The defect: MEDTEC IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2010 AMBULANCES MANUFACTURED FROM SEPTEMBER 14, 2007, THROUGH APRIL 15, 2010. THE REAR FACING AMBULANCE ATTENDANT SEAT WAS NOT EQUIPPED WITH A TYPE 2 SEAT BELT ASSEMBLY, AND SO THE VEHICLES FAIL TO COMFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION."
The risk: USE OF AN IMPROPER SEAT BELT ASSEMBLY MAY INCREASE THE RISK OF INJURY TO THE SEAT OCCUPANT IN THE EVENT OF A CRASH.
The remedy: MEDTEC WILL NOTIFY OWNERS AND DEALERS WILL INSTALL A TYPE 2 SEAT BELT ASSEMBLY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 6, 2010. OWNERS MAY CONTACT MEDTEC TOLL-FREE AT 1-866-263-3832.
MEDTEC AMBULANCE CORPORATIONView on NHTSA.gov

What a recall is

Safety recall
A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation
NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Elsewhere on this vehicle

Data sources