2012 Mercedes-Benz AMG C63

Fuel leaking in the back seat of the car

NHTSA ID

11771513

Incident

Oct 15, 2026

The electronic steering lock failed resulting in my car being completely disabled. My safety was not at risk in this particular instance. I was left stranded in a parking lot at night. The component was not inspected by the manufacturer or dealer. The manufacturer/dealer did not inform anyone that this problem will happen to every car with this compensation. This component failed without warning/symptoms/messages. It will fail on all Mercedes Benz cars from 2008-2016. The problem has not been confirmed or communicated by the dealer. Other Mercedes benz owners have encountered this problem resulting in their cars being disabled and leaving them stranded.

NHTSA ID

11676056

Incident

May 28, 2025

EXTREMELY DANGEROUS FUEL LEAK - FUEL STARTED TO LEAK FROM THE TOP OF THE GAS TANK, INSIDE THE CAR FROM UNDER THE DRIVER SIDE REAR PASSENGER SEAT. VEHICLE WAS TAKEN TO CLOSEST SHOP AVAILABLE WHEN HEAVY FUEL SMELLS WERE NOTICED INSIDE VEHICLE WHILE DRIVING. A LOCAL TIRE SHOP, HAMIL FIRESTONE, LOOKED UNDER THE CAR AND IDENTIFIED THAT FUEL WAS LEAKING DOWN THE FRAME TO THE ROAD. SOMEHOW GASOLINE WAS ACTUALLY LEAKING FROM INSIDE THE CAR. I CONTACTED MERCEDES CORP IMMEDIATELY AND THEY SENT A TOW TRUCK TO COLLECT THE VEHICLE. I WAS TOLD THAT DUE TO THE NATURE OF THE ISSUE IT WAS EXTREMELY DANGEROUS TO DRIVE THE CAR. MERCEDES SAID THAT DESPITE THE CAR BEING OUT OF WARRANTY, SOMETHING LIKE THIS WOULD GO TO "UPPER MGMT" FOR REVIEW AND SHOULD BE TAKEN CARE OF BY MERCCEDES. NOW THE VEHICHLE IS STILL AT THE LOCAL MERCEDES DEALERSHIP WHERE THE HAVE CONFIRMED AN ISSUE WITH THE FUEL PUMP AND SEALS, AND THAT THE CAR IS DEFINETLY LESKING FUEL OUT ONTO THE ROAD.... BUT DESPITE A RECALL ON ALMOST EVERY OTHER 2012 MODEL CAR FOR THE SAME ISSUE, THEY ARE SAYING BECAUSE THIS VIN IS NOT INCLUDED IT DOESN'T MATTER THAT IT IS DOING THE SAME THING. THEY WANT ME TO PAY FOR THE REPAIR. I EXPLAINED THAT I OR MY CHILDREN, OR EVEN ALL OF US COULD HAVE BEEN INVOLVED IN A FATAL CAR FIRE DUE TO THE ISSUE!!! MERCEDES DIRECT RESPONSE WAS, "THAT IS THE RISK OF DRIVING A VEHICLE OUT OF WARRANTY." UNACCEPTABLE!!!

NHTSA ID

11390625

Incident

Jan 11, 2021

Mileage

70,000 mi

2012 MERCEDS BENZ C63 AMG. CONSUMER WRITES IN REGARDS TO MERCEDES BENZ DEALER NOT REPLACING OR REPAIRING ANY DEFECTIVE VEHICLES PARTS. *LD THE CONSUMER STATED THE CLEAR COAT PAINT WAS PEELING OFF OF THE BRAKE CALIPERS.*JS

NHTSA ID

11042428

Incident

Aug 24, 2017

TL* TAKATA RECALL. THE CONTACT OWNS A 2012 MERCEDES-BENZ C63 AMG. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 17V017000 (AIR BAGS); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE DEALER (MERCEDES-BENZ OF TYSONS CORNER, 8545 LEESBURG PIKE, VIENNA, VA 22182) WAS CONTACTED AND CONFIRMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS NOT CONTACTED. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

NHTSA ID

11041053

Incident

Jan 10, 2017

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy The intent of this document is to reduce noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some scenarios are normal and some are induced by driving style like those listed below: • Driving style such as two footed driving where the pad might be in constant contact with the rotor. • Brake pressure and application style (stop‑and‑go traffic with consistent light brake pressure “riding brakes” where the brakes cannot cool sufficiently between applications). This can cause the brake pads to glaze and have a smooth/glassy surface which can induce noise. • When ambient temperatures rise during summer peak and during cooling and cold winter months. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3‑4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re‑assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and Molykote as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston‑side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Be sure to remove both brown paper backing sides of the adhesive film, it is double sided adhesive film. 5. If adhesive is already installed on backing plate where pistons contact the back of the pad, you may gently scrape off and re‑apply a new adhesive or Molykote. Must not apply the Molykote on top of the adhesive. 6. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 7. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 8. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper /carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston‑side brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off

Complaint A popup is seen on the HU with the message "data connection temporarily not available". Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.Navigation 7.iHeartRadio 8.Traffic Cams Cause MB Apps is sundowned for all vehicles with NTG4.5 and NTG5 Head Unit Variant. Remedy No support available for NTG4.5 and NTG5 Head Unit Variants for MB App related topics. Note: Please do not create TIPS. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint Crackling and cracking noise from the outer wheel on the front axle when cornering Cause The noise is generated by a micromovement on the contact surface between the rim and the brake disk (wheel bolt group) and may be intensified by potential soiling. The more lightweight rim (AMG forged rim) transmits the noise louder; in the case of cast rims, the noise is generally not perceptible. This is not a technical defect, but rather a complaint concerning comfort. Safe operation of the vehicle is ensured at all times. Remedy Important note: The operations described below do not represent a permanent remedy in every case. The noise may reoccur again after an indefinite period of time; sanding the rims with abrasive media multiple times is not permissible. Only cleaning using the Hazet tool 4960-160 (recommendation) can be performed without any concerns each time the wheel is changed or if the complaint reoccurs. Replacing the parts (rim, wheel bolts, wheel bearings, wheel hub, brake disk) is not expedient in the event of this complaint. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Clean the components of the wheel bolt connection according to the WIS instructions Sand down the rim and brake disk bowl by performing the following steps: • Manually sand rim (old design only) in area of water drain bores (Figure 1; item A), approx. 1.5 cm left and right of water drain bore (Figure 2) Note: Use abrasive paper with grit size 80. The grooving in this area should no longer be visible (sand down approx. 0.1-0.2mm) • Also sand brake disk bowl using emery cloth or abrasive paper with a grain size of 120 • For vehicles equipped with the AMG ceramic brake system (B07), abrasive paper may not be used for cleaning on the brake disk side Note: Do not use any cleaning agent when cleaning on the rim side. Cleaning using abrasive paper with a grain size of 80 will suffice. Do not apply any grease, lubricant or paste after cleaning The brake disk bowl should be "bare metal" in the area of the imprints made by the hole (Figure 3)