2023 Mercedes-Benz AMG EQS

The contact owns a 2023 Mercedes-Benz EQS AMG 4MATIC. The contact stated that while driving at a slow speed, the vehicle stalled and failed to restart. While exiting the vehicle, the vehicle shut off. The vehicle automatically locked after closing the door. The contact's child became locked inside the vehicle on several occasions. The contact's husband was able to unlock the doors with his phone. The contact had previously been stranded for three hours. The vehicle was towed on a flatbed to the local dealer, and a software check was performed. The vehicle was diagnosed, and it was determined that the coolant level was low. The contact was informed that the anti-theft system was working as designed. The vehicle was not repaired. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 47,000.

NHTSA ID

11747382

Incident

Jun 3, 2026

Mileage

47,000 mi

- Emergency braking, Yes available. - It's a fatal issue. My family and I are at collision risk. - No they always say “Not duplicate the issue” -Inspected by the dealer. - the collision warning Sound went off. I was driving on the highway by speed 60 mph and no cars were behind me and the car in front of me was so far and suddenly the emergency brake sound went off and the car suddenly stopped with hard and terrified brake and all the seat belts had tightened up.

NHTSA ID

11615719

Incident

Sep 10, 2024

SEE UPLOADED FILE SENT TO MERCEDES-BENZ. INCLUDES DESCRIPTION OF INCIDENT

NHTSA ID

11579341

Incident

May 26, 2023

When operating the vehicle, the MBUX system will switch the User Profile without warning. When doing this it will reposition the driver seat for the new profile which causing interruption to the driver operating the vehicle. During the unexpected change the driver seat and the external mirrors will reposition to the switched User Profile. This has been reported to the Dealer (Mercedez Benz of Tampa) numerous times. The MBUX System was updated by the dealer Service Dept. (04 Jan - 10 Jan 2024) but has not resolved the problem. The dealer has been informed this presents a safety issue due to the unexpected User Profile switch and the changes to the driver's seat position and external mirror positions. Despite text messages to Service Technician and Sale Associate the reports has been ignored. There's no consistency or predictable method to know when the issue happens. It has happened multiple times since purchasing the vehicle on 21 August 2023 and multiple times since the MBUX System was updated 04 Jan - 10 Jan 2024.

NHTSA ID

11575009

Incident

Feb 24, 2024

The automatic emergency braking failed.

NHTSA ID

11545526

Incident

Jun 11, 2023

The contact owns a 2022 Mercedes-Benz EQS. The contact stated that while reversing, the collision avoidance system inadvertently activated, causing the vehicle to abruptly stop. Additionally, while driving forward, the failure occurred, causing unknown messages to be displayed and alarms to be activated inside the vehicle. Also Additionally, the system also erroneously activated while using the turn signals to switch from one lane to the other even though there no vehicles nearby. While the adaptive cruise control was activated, another vehicle switched into the same lane and the alarm sounded and unknown messages were displayed even though the vehicle was several car lengths ahead. The cause of the failure was not yet determined. The manufacturer and the local dealer were notified of the failure. The failure mileage was 20,000.

NHTSA ID

11531557

Incident

Dec 11, 2022

Mileage

20,000 mi

I had a forward collision with 2 cars. My brake has been failed and forward collision warning system failed. I leased the car because of the safety features but I am really disappointed. Since I had my kids in the car with me. It was a really horrible experience and I can't drive the car anymore because of the safety issues.

NHTSA ID

11530268

Incident

Jul 4, 2023

Complaint Crackling and cracking noise from the outer wheel on the front axle when cornering Cause The noise is generated by a micromovement on the contact surface between the rim and the brake disk (wheel bolt group) and may be intensified by potential soiling. The more lightweight rim (AMG forged rim) transmits the noise louder; in the case of cast rims, the noise is generally not perceptible. This is not a technical defect, but rather a complaint concerning comfort. Safe operation of the vehicle is ensured at all times. Remedy Important note: The operations described below do not represent a permanent remedy in every case. The noise may reoccur again after an indefinite period of time; sanding the rims with abrasive media multiple times is not permissible. Only cleaning using the Hazet tool 4960-160 (recommendation) can be performed without any concerns each time the wheel is changed or if the complaint reoccurs. Replacing the parts (rim, wheel bolts, wheel bearings, wheel hub, brake disk) is not expedient in the event of this complaint. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Clean the components of the wheel bolt connection according to the WIS instructions Sand down the rim and brake disk bowl by performing the following steps: • Manually sand rim (old design only) in area of water drain bores (Figure 1; item A), approx. 1.5 cm left and right of water drain bore (Figure 2) Note: Use abrasive paper with grit size 80. The grooving in this area should no longer be visible (sand down approx. 0.1-0.2mm) • Also sand brake disk bowl using emery cloth or abrasive paper with a grain size of 120 • For vehicles equipped with the AMG ceramic brake system (B07), abrasive paper may not be used for cleaning on the brake disk side Note: Do not use any cleaning agent when cleaning on the rim side. Cleaning using abrasive paper with a grain size of 80 will suffice. Do not apply any grease, lubricant or paste after cleaning The brake disk bowl should be "bare metal" in the area of the imprints made by the hole (Figure 3)

A software update is available to enable Plug & Charge at Tesla Superchargers. Schedule a workshop visit with your dealer to receive the update.

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Do not replace parts. Please open a TIPS case to the Body/Chassis/Entertainment inbox but read the below carefully: • The vehicle must be exhibiting the concern as shown in the attachment videos. • The vehicle DOES NOT need to be at the dealer, nor does it need to be brought into the dealership. • If the geographic location is known, it is very important that it is provided. • Provide any pictures or videos, if available. A new software for the head unit is scheduled for tentative release in Q3 2026.

Complaint Radio station cover art does not refresh when switching stations. The UI continues to show the old station’s artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The E505.9 software is released and available in XENTRY Q3 2026.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.