2026 Mercedes-Benz AMG GLC43

Complaint After an "Over the Air" update (OTA), FM or SDARS radio reception is limited; only a few stations are found. Cause The firmware installation was incomplete. Remedy In the A26/17 control unit "MBUX multimedia system" (head unit), use XENTRY to carry out the special process "All Modules"; this will reinstall the firmware completely.

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Do not replace parts. Please open a TIPS case to the Body/Chassis/Entertainment inbox but read the below carefully: • The vehicle must be exhibiting the concern as shown in the attachment videos. • The vehicle DOES NOT need to be at the dealer, nor does it need to be brought into the dealership. • If the geographic location is known, it is very important that it is provided. • Provide any pictures or videos, if available. A new software for the head unit is scheduled for tentative release in Q3 2026.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint Radio station cover art does not refresh when switching stations. The UI continues to show the old station’s artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The E505.9 software is released and available in XENTRY Q3 2026.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.