2021 Mercedes-Benz AMG GT

My 2021 Mercedes-Benz AMG GT 43, VIN [XXX] , has had a recurring safety issue with the transmission wiring harness and connector X279. Mercedes-Benz said this connector can let water in, which can cause a short circuit, overheating, and a fire risk while the car is parked and off. That is why the vehicle was covered by recall 24V445 / MBUSA Campaign 2024100002. This same issue was already addressed once before in January 2023 under MBUSA Campaign 2022080010 / NHTSA 22V-533, when the connector was checked and reworked and a bracket was installed. Even after that, the car later had to go back again on November 29, 2024 for the newer recall repair, when the original two-part harness was replaced with a one-part harness. The part that concerns me most is that this is not just a routine repair issue. It is a fire risk that can happen while the vehicle is parked with the ignition off. I am also concerned that the recall and service records do not clearly show the exact completion date in the manufacturer’s system. I am asking NHTSA to record this complaint and review the defect history and repair history for this vehicle. I can provide the recall notices, service records, purchase contract, vehicle history report, and the notice I already sent to Mercedes-Benz USA. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11739859

Incident

Nov 29, 2024

AVAILABLE FOR INSPECTION UPON REQUEST ISSUE WAS REPRODUCED AT DEALESHIP. ISSUE IS EASY TO IDENTIFY. VEHICULE WAS INSPECTED BY DEALERSHIP, MANUFACTURER IS AWARE. FAULT LIGHT ON DASHBOARD SHOW A FAULT ICON THE 2021 AMG GT BLACKSERIES HAVE AN ACTIVE REAR WING. A PART OF THE ACTIVE REAR WING IS ACTIVE BUT HAS A HIGH FAILURE WHICH AT SOME SPEEDS CAN BE DANGEROUS BECAUSE THE ACTIVE PART IS NOT WORKING AND DO NOT PROVIDE THE DOWNFORCE THAT IT SHOULD BECAUSE OF THE ACTATOR FAILURES. THERE ARE A HIGH NUMBERS OF REPLACEMENT REQUESTED THROUGHT THE MERCEDES NETWORK BUT THEY ARE BEING REPLACED BY THE SAME PART # NOT AN UPDATED ONE TO AVOID FAILURES. SOME OWNERS DO NOT HAVE A REPLACEMENT DUE TO NONE IN STOCKS. THE 2021 IS UNDER WARRANTY BUT AMG MERCEDES HAS NOT , YET, INFORMED OWNERS OF THE POTENTIAL HAZARD. THE ACTIVE PART OF THE REAR WING WHEN FAILED IS SIMPLY NOT RESPONSIVE (NOT MOVING ACCORDING TO SPEEDS OR BRAKING ACTIONS). PLEASE REVIEW THE ISSUE BEFORE SOMEONE GETS HURT. THANK YOU

NHTSA ID

11660293

Incident

Sep 3, 2024

Complaint During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time. OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: ‑ Hitting the curb/posts with the front wheels. ‑ Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). ‑ Cracks (1) ‑ High pressure cleaner (2) ‑ Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz, has determined that on certain MY 2019-2021 C-Class, G-Class, GLC, GT, S-Class (205, 463, 253, 190 & 222 platforms) vehicles, the engine control unit software does not correspond to current production specifications. It is therefore possible that on-board diagnostics and/or exhaust gas emissions requirements may not be fulfilled.

Complaint Check Engine Light ON with DTC P012800 "The Coolant Temperature is Below the Specified Temperature" active and/or stored in the ME (N3/10). There are no drivability concerns related to this complaint. Cause Root cause varies Remedy Prior to performing any repairs for this complaint: With a cold engine, pressurize the high temp coolant circuit and while it's under pressure, release the cap on the low temp coolant circuit and check if the pressure drops right away or not. If the pressure drops, the lower coolant hoses are swapped. Correct this, fill, bleed and test drive the vehicle. If the complaint returns, then continue with the steps below. IMPORTANT: Use VMI to check for the following emission extended warranty –> Engine Thermostat (incl. software update) MY19-23, Various Models and Platforms (167, 190, 205, 213, 217, 222, 223, 232, 253, 290, 463) If the vehicle is covered under the above emission extended warranty, please perform steps outlined in the accompanying NCU prior to those outlined in this document. If vehicle is not covered under the above emission extended warranty or the complaint continues to occur, then proceed as follows: Check for available software updates to the ME (N3/10). If updated software is available, perform the update, clear the DTC and the perform each of the "WARM START" and "COLD START" test drives listed below twice. If the code does not re-appear then release the vehicle. If there is no new software available OR the DTC returns after the test drives then perform the following steps: • Drain the coolant through a fine mesh sieve and check for signs of debris. Additionally, inspect the coolant reservoir for debris. If any debris is found take pictures of the reservoir and the mesh filter and "flush" the system at least 2-3 times to clear as much of the debris as possible • Replace the thermostat and bleed the system as outlined in AR20.00-P-1142-04A, evacuate the system for 20-30 minutes instead of the 5 minutes specified in step 22 • NOTE: Please use all the tools specified in the AR document. The DTC will continue to populate if the circuit is not properly bled • NOTE: There are two valid thermostats to choose from in the parts section of this LI. Please verify which PN is applicable for the vehicle being worked on via XENTRY Parts Information • After bleeding the system clear the DTC and perform each of the "WARM START" and "COLD START" test drives listed below twice. If the DTC does not reappear after the tests, release the vehicle If the ME (N3/10) software is up to date, the thermostat has already been replaced, and the complaint persists open a TIPS case and attach the following documents: • Initial quick test • ME (N3/10) control unit log • The results of an R48 test from a “yes” response and from a “no” response • Pictures of the coolant reservoir and mesh sieve (mentioned above) WARM START · Begin with the engine coolant temperature at approximately 50 degrees C · Activate the AC system, if defrost is not in use open the windows · Drive the car normally until a coolant temperature of 75 degrees C is achieved · Depress the accelerator pedal 50% for ~5 seconds (partial acceleration) · Let off the accelerator pedal and let the car coast for ~10 seconds · Continue to drive the car normally COLD START · Drive for ~7 miles (normal driving) · Shut off the engine in a parking lot (or similar), wait 30 seconds, then restart and continue driving · Depress the accelerator pedal 50% for ~5 seconds (partial acceleration) · Let off the accelerator pedal and let the car coast for ~10 seconds · Continue to drive the car normally

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).