2020 Mercedes-Benz AMG GT

The recently completed recall on this vehicle back in 2021 last year for the wheel hub caps. Approximately two days ago, I drove it off the dealership and after I got home I noticed the wheel hub cap was missing from my passenger side. This is a known hazard and hasn't been remedied correctly from the last recall service it had and I'm sure it fell off again. Would I be able to get this replaced for free? Because the dealership told me it wouldn't be covered under warranty and they're asking me to fork over $120 for a plastic hub cap.

NHTSA ID

11476730

Incident

Jul 29, 2022

1)The side cover on the driver’s seat covering the seatbelt harness area detaches from the seat. The defect has been shown to the Mercedes dealer, Autohaus on Eden of Northbrook, IL several times. The dealer refuses to fix it. 2) The wheel hubcaps fly off during a normal drive of 30 mph risking injuries to other vehicles. The recall has been issued by NHTSA, but the same dealer refuses to acknowledge and fix it.

NHTSA ID

11462109

Incident

Apr 18, 2022

WHILE LEAVING WORK AND MAKING A RIGHT TURN MY CAR DIED, A QUICK MALFUNCTION NOTIFICATION CAME ON THE DISPLAY THEN NOTHING. I WAS STUCK IN THE MIDDLE OF THE ROAD. IT TOOK MINUTES TO BE ABLE TO START UP THE CAR AND GET IT TO SHIFT. IT WAS A COMPLETE FAILURE IN MIDDLE OF TRAFFIC. IT'S NOW BEEN AT THE DEALER FOR 16 DAYS. NO END IN SIGHT. MBUSA HAS BEEN HORRIFIC IN THEIR CUSTOMER SERVICE. NOTHING SHOWS ON THE DIAGNOSTIC CHECK. BUT. ON A TEST DRIVE WHILE LEAVING THE CAR IN THE HOT PHOENIX SUN AND IT DID THE SAME FAILURE. THE SAME ISSUE HAPPENED WITH MY HUSBANDS CAR ON THE SAME DAY SAME MODEL

NHTSA ID

11341031

Incident

Jul 8, 2020

Mileage

2,700 mi

IN A BUSY INTERSECTION I WAS MAKING A LEFT TURN, AS I WAS EDGING OUT MY CAR DIED, EVERYTHING STOPPED, A QUICK MALFUNCTION ERROR WAS SEEN ON DISPLAY. TOOK MY 5 TRIES TO GET GOING AND PULL OFF, VERY SCARY, MY WIFE HAS THE SAME 2020 MODEL, SHE HAD THE SAME ISSUE TWO HOURS LATER, IT WAS THE HOTTEST DAY TO DATE IN PHOENIX, BOTH CARS WERE OUTSIDE, SHE WAS LEAVING HER PARKING LOT AT WORK WHEN IT HAPPENED. TWO CARS THE SAME MODEL, SAME DAY HAVE TIS ISSUE WITH LESS THAN 3K MILES, BOTH CARS ARE IN THE SHOP, 8 DAYS AND COUNTING, I FILED A COMPLAINT WITH MEBEN THAT WE WANT ARE MONEY BACK, LOCAL DEALER AND MBENZ ENGINEERS ARE INVOLVED,. NO RESOLUTION. DEALER RAN DIAGNOSTIC TEST, SHOWED NOTHING, BUT LEAVING THE CAR OUT ALL DAY AND TAKING FOR A TEST RIDE THEY HAD THE SAME CATASTROPHIC FAILURE. MY WIFES VIN IS [XXX], ITS A HUGE SAFETY ISSUE AND THE ATTITUDE IS A MERE SHRUG OF THE SHOULDERS REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *CC

NHTSA ID

11339593

Incident

Jul 8, 2020

Mileage

3,000 mi

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy The intent of this document is to reduce noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some scenarios are normal and some are induced by driving style like those listed below: • Driving style such as two footed driving where the pad might be in constant contact with the rotor. • Brake pressure and application style (stop‑and‑go traffic with consistent light brake pressure “riding brakes” where the brakes cannot cool sufficiently between applications). This can cause the brake pads to glaze and have a smooth/glassy surface which can induce noise. • When ambient temperatures rise during summer peak and during cooling and cold winter months. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3‑4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re‑assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and Molykote as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston‑side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Be sure to remove both brown paper backing sides of the adhesive film, it is double sided adhesive film. 5. If adhesive is already installed on backing plate where pistons contact the back of the pad, you may gently scrape off and re‑apply a new adhesive or Molykote. Must not apply the Molykote on top of the adhesive. 6. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 7. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 8. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper /carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston‑side brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off

Complaint During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time. OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: ‑ Hitting the curb/posts with the front wheels. ‑ Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). ‑ Cracks (1) ‑ High pressure cleaner (2) ‑ Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!