2009 Mercedes-Benz C63 AMG

The tail lamps of my car do not function appropriately - the right tail lamp is completely dead most of the time and the left tail lamp constantly dims and flickers. Mercedes previously issued a recall campaign (no. 2014050001) because "DAG determined that oxidation on the ground pin connector for the rear tail lamps of subject vehicles can result in a dimming of the tail lights or loss of tail lamp functions. . . . [t]he loss of a rear tail lamp reduces the rearward visibility of subject vehicles . . . and may increase the likelihood of a rear end crash." The recall has been performed on my car, but the issues and danger continue to persist. I visually inspected the pin connectors of the tail lamps, confirmed that they still suffer from oxidization (and that they may have slightly burned due to the oxidization), causing the same continuing issues that were at the heart of the prior recall campaign. I reached out to Mercedes' corporate customer service, explained to them in writing that the same issues continue to exist (oxidization of the pin connectors which continue to cause tail lamp malfunction), showed them photos of clear oxidization of the pin connectors, and pleaded with them regarding the continued danger that is caused by the malfunctioning tail lamps. Despite the continuing clear defects and obvious dangerous conditions, Mercedes has refused to provide any assistance to repair the tail lamps. This is a serious design defect, and a quick google search confirms that it continues to be a widespread problem. At minimum, Mercedes should be pressed by the NHTSA to repair my tail lamps, free of cost. However, given that it appears that it continues to be a widespread problem that could potentially affect thousands of cars that continue to be road worthy, the NHTSA should investigate the extent to which Mercedes should be pressed to issue a second wider recall, because the first recall has not resolved the defects and dangerous conditions.

NHTSA ID

11748303

Incident

Jul 4, 2026

FUEL PUMP HOUSING CRACKED AND WAS LEAKING FUEL. THIS IS A PLASTIC PART. THE FUEL PUMP IS LOCATED UNDER THE REAR SEAT, SO THERE WAS FUEL INSIDE THE CAR. I NOTICED A STRONG GAS ODOR AND UPON INSPECTION, FOUND THE FAILED PUMP WITH GAS LEAKING FROM IT.

NHTSA ID

11289344

Incident

Oct 20, 2018

Mileage

85,000 mi

TAKATA RECALL I BOUGHT MY VEHICLE FROM MERCEDES BENZ OF LONG BEACH ON JULY 10, 2017. WHEN I PURCHASED THE VEHICLE THEY DID NOT INFORM ME OF ANY RECALLS! I SEARCH MY VIN TODAY 1/05/2019 THRU THE WEBSITE AND I FIND OUT THERE IS 2 RECALLS FROM 2016 AND IT SAYS THERE ARE NO REMEDIES YET AVAILABLE AND THE PROBLEM WAS ESTABLISHED SINCE 2016! I TAKE THIS RECALL SERIOUSLY AS IT SAYS THE AIRBAG MAY EXPLODE AND SHARP PIECES OR SHRAPNEL MAY HIT THE DRIVER CAUSING SERIOUS INJURY OR DEATH. I WAS DRIVING THE VEHICLE EVERYDAY TO WORK,TO DO ERRANDS, AND TO SCHOOL BUT NOW SINCE FINDING OUT THAT THE AIRBAG CAN KILL YOU INSTEAD OF SAVING YOU I WILL STOP DRIVING THE CAR UNTIL THERE IS A SOLUTION. I REALLY FEEL DECEIVED FROM MERCEDES BENZ OF LONG BEACH FOR NOT TELLING ME THAT THERE IS A VERY SERIOUS RECALL REGARDING THE AIRBAGS EQUIPPED ON THE VEHICLE I PURCHASED FROM THEM. IF THERE IS YET TO BE A REMEDY FOR THIS PROBLEM I FEEL AS IF MERCEDES BENZ OF LONG BEACH SHOULD PROVIDE A LOANER VEHICLE UNTIL THERE IS A SOLUTION TO THIS PROBLEM. I KNOW THAT IF I CONTINUE TO DRIVE THE VEHICLE AS IS AND I HAPPEN TO GET INTO AN ACCIDENT IT WILL NOT BE A GOOD SITUATION ON BOTH ENDS.

NHTSA ID

11165425

Incident

Apr 10, 2017

Mileage

49,500 mi

Complaint Crackling and cracking noise from the outer wheel on the front axle when cornering Cause The noise is generated by a micromovement on the contact surface between the rim and the brake disk (wheel bolt group) and may be intensified by potential soiling. The more lightweight rim (AMG forged rim) transmits the noise louder; in the case of cast rims, the noise is generally not perceptible. This is not a technical defect, but rather a complaint concerning comfort. Safe operation of the vehicle is ensured at all times. Remedy Important note: The operations described below do not represent a permanent remedy in every case. The noise may reoccur again after an indefinite period of time; sanding the rims with abrasive media multiple times is not permissible. Only cleaning using the Hazet tool 4960-160 (recommendation) can be performed without any concerns each time the wheel is changed or if the complaint reoccurs. Replacing the parts (rim, wheel bolts, wheel bearings, wheel hub, brake disk) is not expedient in the event of this complaint. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Clean the components of the wheel bolt connection according to the WIS instructions Sand down the rim and brake disk bowl by performing the following steps: • Manually sand rim (old design only) in area of water drain bores (Figure 1; item A), approx. 1.5 cm left and right of water drain bore (Figure 2) Note: Use abrasive paper with grit size 80. The grooving in this area should no longer be visible (sand down approx. 0.1-0.2mm) • Also sand brake disk bowl using emery cloth or abrasive paper with a grain size of 120 • For vehicles equipped with the AMG ceramic brake system (B07), abrasive paper may not be used for cleaning on the brake disk side Note: Do not use any cleaning agent when cleaning on the rim side. Cleaning using abrasive paper with a grain size of 80 will suffice. Do not apply any grease, lubricant or paste after cleaning The brake disk bowl should be "bare metal" in the area of the imprints made by the hole (Figure 3)

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Noises at the front axle when cornering or maneuvering (video files attached) Note: Save video files locally and play them with Windows Media Player. Cause Driving with summer tires in combination with low outside temperatures. At low outside temperatures or in wet conditions, a noise may be produced at the outer wheel on the front axle while maneuvering with sharp steering angles. Note: AMG vehicles with 4MATIC of model series 217 (without code 494) and model series 222 have a modified axle geometry compared with series production vehicles to provide more sporty handling. The problem cannot be remedied by changing the axle settings.

Complaint Potential corrosion on the rear axle carrier Cause Due to market-specific conditions such as moisture, ingress of dirt and/or environmental influences, corrosion can occur on the rear axle carrier Remedy In the event of a complaint, the optimized repair method must be used when replacing the rear axle carrier. The repair method for the respective model series can be found in the attachment. Repair packages are available in Xentry Repair Packages for the special processing of rear axle carriers Note: Please utilize flexible wand (319-SAT1058826) along with the Cavity Preservation Gun (W 000 588 03 72 00) for cavity wax application to improve coverage and reduces labor efforts. The flexible wand may be obtained through the Mercedes-Benz Standard Service Equipment Program website.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.