2024 Mercedes-Benz E 350 4MATIC

The lane-keeping assist function (In-Lane control, part of the driver-assistance suite) does not turn off when commanded. The driver selects the control to disengage, and the system remains active and continues to apply steering input. This is a recurring condition and it is getting more frequent. A driver-assistance steering function that cannot be switched off removes driver authority over the steering at the moment the driver is trying to take control, which is a safety risk in normal driving and especially during evasive maneuvers, lane changes, and construction or debris avoidance. The condition was reported to the selling dealer in writing on June 17, 2026 as part of a recurring driver-assistance concern. During the subsequent B service visit the dealer inspected the radar sensors and applied software updates to the steering column module, steering wheel, electric power steering, and driver-assistance control units. The dealer could not duplicate the concern and did not perform a system calibration. The condition has continued after that service. The vehicle has approximately 17,428 miles. There has been no crash, no injury, and no fire. A separate recurring concern on the same vehicle: it reports its doors as unlocked when they are in fact locked, and issues a vehicle-unlocked notification while the vehicle is locked. This now occurs on a near-daily basis and was also reported to the dealer on June 17, 2026 with no diagnosis on record.

NHTSA ID

11746468

Incident

Jun 25, 2026

The contact owns a 2024 Mercedes Benz E. The contact stated that while the vehicle was parked, and started, the instrument panel and infotainment screen became blank. No warning indicators or audible assistance and other vehicle assistance were not able to display due to the failure. The dealer was contacted; however, the vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 21,000.

NHTSA ID

11741513

Incident

Jun 1, 2026

Mileage

21,000 mi

On a recent drive, my 2024 Mercedes-Benz E350 VIN: [XXX] suffered a catastrophic safety hazard involving a complete loss of drive power and sudden engine shutdown while operating at highway speeds. I had to navigate across active highway lanes with no engine propulsion to reach safety. ​Simultaneously, the vehicle experienced a widespread failure of its master interior electrical grid. The driver's power seat became permanently frozen in a fully reclined position while driving, creating an immediate driver-ergonomic safety hazard. Multiple interior USB charging ports and the passenger-side power seat also lost power entirely. ​This combination of engine stalling and localized interior electronic failure strongly aligns with NHTSA Recall 24V-115, which involves faulty 80-Amp fuses in the main fuse box causing a loss of propulsion. The vehicle also currently displays an open, unresolved safety recall for its airbag systems. The manufacturer's dealership is attempting to charge multiple diagnostic fees to investigate these interconnected issues rather than processing them under an active safety campaign. I am filing this report to document a severe, active propulsion failure in the field that represents an immediate threat to life and highway safety. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11739972

Incident

May 4, 2026

Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the on‑board electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) • It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause • In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. • There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10‑P‑1127WT). Note: An adequate voltage from the on‑board electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the on‑board electrical system battery. ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 2. Connect diagnostic system (see AD00.00‑P‑2000‑06FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view → Drive systems → N127 ‑ "Drivetrain" control unit (CPC) ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 4. Update software for control unit N127 (CPC) (see AR54.21‑P‑0014‑01Y). Info: To do so, select the following menu items: Adaptations → Control unit update → Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 5. Disconnect diagnostic device from vehicle (see AD00.00‑P‑2000‑06FR). ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 6. Disconnect charger from vehicle (see AR54.10‑P‑1127WT).

Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, is launching an OTA update to the subject vehicles to provide an enhanced user experience. This OTA update includes enhancements to the MBUX voice assistant. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

Complaint Wheezing noises/squeaking noises from the front shock absorbers when passing over surface undulations and rough road. Noise MUST match those heard in the attached videos. Cause • Wheezing noises: Flow noises of the damper oil • Squeaking noises: From the mechanical rubber valve in the dividing piston Remedy In case of complaints, the front shock absorbers must be replaced. If shocks have been replaced and noise persists, please open a TIPS case to the Body, Chassis, Entertainment inbox.

Complaint Wheezing noises/squeaking noises from the front shock absorbers when passing over surface undulations and rough road. Noise MUST match those heard in the attached videos. Cause • Wheezing noises: Flow noises of the damper oil • Squeaking noises: From the mechanical rubber valve in the dividing piston Remedy In case of complaints, the front shock absorbers must be replaced. If shocks have been replaced and noise persists, please open a TIPS case to the Body, Chassis, Entertainment inbox.

Complaint Oil seeping from turbocharger oil return line at connection to engine block. Low oil level warning. Oil observed under vehicle. Cause Return line under tension due to turbo rotation. Remedy Inspect turbocharger housing for rotation (refer to attachment). If rotation is confirmed, the turbocharger and oil return line must be replaced.‑Resealing or replacing only the oil return line is not sufficient and will not resolve the symptom.‑Clean noise insulation on right side of engine if necessary. Replace insulation if cleaning is not sufficient.‑Observe foot notes regarding additional parts in XENTRY parts information when ordering turbocharger.

Issue A software update will be performed that provides enhancements to the robustness and system stability of the communication module. The update is free of charge and runs in the background, which takes about 8 minutes to install. During this time, the vehicle can be driven without any restrictions, and the new software will be active with the next ignition cycle. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.