2026 Mercedes-Benz E 350 4MATIC

Mercedes-Benz E350 Mild Hybrid was purchased new on XXX. Vehicle had approximately 291 miles and had been owned 25 days, when incident occurred on XXX at approximately 9:30am. Incident occurred during normal interstate driving (I-10 between [XXX] and [XXX]) at approximately the posted speed limit of 60mph. Weather was partly cloudy, not raining. A sudden loud explosive sound occurred, similar to a gunshot. There were no warning lamps, messages, or other symptoms prior to the explosive sound. Neither of 2 occupants in vehicle observed an object strike the vehicle. Sunroof was completely closed at time of incident. Passenger opened inside cover of sun roof and immediately observed shattered panoramic roof glass, with almost half of the sunroof gone. Remainder of sunroof was cracked into very small fragments. Glass appeared to largely disperse outward; interior sunshade prevented glass from entering the passenger compartment, although there were shards of glass lying within the sunshade. Vehicle was safely removed from traffic. No injuries occurred. But half of glass from sunroof was scattered toward other lanes of busy interstate traffic. Passenger safety could've been compromised had the glass torn the soft fabric sunshade. Passenger safety could've been compromised if driver had been distracted by the explosive sound. Glass could've been safety hazard for other vehicles behind mine. Mercedes-Benz denied warranty coverage and refused to provide owner a written engineering explanation of the cause of the accident. Mercedes-Benz field technical rep and dealer service department reviewed the car's damages. Vehicle has since been repaired at owner's expense. Owner has photos of damaged roof prior to repair. Owner plans to sell vehicle on or about XXX. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11750962

Incident

Jun 10, 2026

1. Car's computer abruptly shutdown all controls/systems when lightly applying brake to stop at yellow light. Lost Total control of car, steering locked, 4 wheel drive locked all wheels, park brake inoperable, doors locked, windows would not operate, key fob was made inoperable, HVAC was inoperable, no lights worked except for Emerg flashers, wipers activated and went erratic, multiple alarms went off saying what Not to do but gave No advice on "What to do", MB SOS made inoperable. see MB Inv 379224 they determined it was EZS control module. BUT MB gave no diagnostics why the car left driver with control of nothing. 2. My safety was put at high risk. Why? I manually opened driver door, it closed itself car on a slight inclined Rd, manually opened trunk to warn others, returned to car and all doors are locked, plus all retractable handles flush with door body manual key useless. Due to perfect weather day, passenger window down 3in allowing to insert arm to unlatch door manually. Car was in lane 2 of 3 lane traffic light intersection. Very busy major road accessing a 6 lane US Hwy. Luckily Police arrived on their way to work, stressed very dangerous location, stayed until car towed away. 3. MB dealer returned car. Will not confirm they will do a root-cause analysis of the total loss of control when one item (EZS) fails and leaves driver totally unsafe. There must be a software malfunction.....too many alarms. MB cannot assure this E350 or (any other one) will not have this type of shutdown again leaving the driver Unsafe. Reading MB car safety policy this dealer and MB USA Georgia do not comply with the policy. Concerns over Driver safety remain very high despite the replaced EZS, software was not diagnosed 4. Dealer stated on Jun 26, the failed EZS is yet to be analyzed and gave no timeline to do so. I gave 26 days for dealer to comply with MB policy. It is not forthcoming 5. Absolutely No warning lamps, alarms or any operational symptoms prior to total shutdown

NHTSA ID

11747174

Incident

May 31, 2026

The contact owns a 2026 Mercedes-Benz. The contact stated that while driving at various speeds, an SRS warning light illuminated. The vehicle was taken to a local dealer, where it was diagnosed as having an electrical issue that needed an SRS replacement. The vehicle was repaired; however, the failure reoccurred. The manufacturer was made aware of the failure. The failure mileage was approximately 32,000.

NHTSA ID

11740420

Incident

May 6, 2026

Mileage

32,000 mi

Restraint system malfunction service required light displayed on dashboard while driving. Vehicle was purchased January 10, 2026. Mercedes Benz E350 4 matic sedan. Safety concerns for operator and public.

NHTSA ID

11737375

Incident

May 3, 2026

Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, is launching an OTA update to the subject vehicles to provide an enhanced user experience. This OTA update includes enhancements to the MBUX voice assistant. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the on‑board electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) • It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause • In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. • There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10‑P‑1127WT). Note: An adequate voltage from the on‑board electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the on‑board electrical system battery. ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 2. Connect diagnostic system (see AD00.00‑P‑2000‑06FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view → Drive systems → N127 ‑ "Drivetrain" control unit (CPC) ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 4. Update software for control unit N127 (CPC) (see AR54.21‑P‑0014‑01Y). Info: To do so, select the following menu items: Adaptations → Control unit update → Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 5. Disconnect diagnostic device from vehicle (see AD00.00‑P‑2000‑06FR). ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 6. Disconnect charger from vehicle (see AR54.10‑P‑1127WT).

Complaint Wheezing noises/squeaking noises from the front shock absorbers when passing over surface undulations and rough road. Noise MUST match those heard in the attached videos. Cause • Wheezing noises: Flow noises of the damper oil • Squeaking noises: From the mechanical rubber valve in the dividing piston Remedy In case of complaints, the front shock absorbers must be replaced. If shocks have been replaced and noise persists, please open a TIPS case to the Body, Chassis, Entertainment inbox.

Complaint Wheezing noises/squeaking noises from the front shock absorbers when passing over surface undulations and rough road. Noise MUST match those heard in the attached videos. Cause • Wheezing noises: Flow noises of the damper oil • Squeaking noises: From the mechanical rubber valve in the dividing piston Remedy In case of complaints, the front shock absorbers must be replaced. If shocks have been replaced and noise persists, please open a TIPS case to the Body, Chassis, Entertainment inbox.

Issue A software update will be performed that provides enhancements to the robustness and system stability of the communication module. The update is free of charge and runs in the background, which takes about 8 minutes to install. During this time, the vehicle can be driven without any restrictions, and the new software will be active with the next ignition cycle. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

Complaint Sporadic warning message in instrument cluster "Engine oil pressure, stop switch off vehicle" (or similar) is shown in red on vehicles with low mileage. Cause Directional control valve may stick. Remedy 1‑ Read off oil level in instrument cluster and correct if necessary. 2‑ Perform approx. 10‑15 engine starts, then clear fault codes. 3‑ Perform road test with vehicle. If fault code reoccurs during road test: Install new directional control valve.