2007 Mercedes-Benz GL320

I WAS DRIVING ON I10 WEST NEAR MOBILE, AL AT NIGHT. I HEARD A LOUD POP NEAR THE REAR OF THE VEHICLE AND FEEL IT LIFT INTO THE AIR AND START BOUNCING UNCONTROLLABLY. THE SEATBELT ENGAGED AND I WAS WORRIED FOR MY 10 MONTH OLD IN THE BACKSEAT. I HAD TO COME TO A COMPLETE STOP TO REGAIN CONTROL. A PASSERBY STOPPED AND SAID IT LOOKED LIKE THE CAR LIFTED 2 FEET IN THE AIR. AFTER RESTARTING THE CAR MULTIPLE TIMES THE AIR SUSPENSION HAS NOT RECALLIBRATED. MY BACK AND NECK ARE SORE. I CALLED MY FIANCE TO MEET MYSELF AND THE BABY SO WE COULD GET HOME. I WAS NOT GOING TO RISK SHAKEN BABY SYNDROME. AFTER GOOGLING THE ISSUE, IT SEEMS THE AIR BAGS IN THE STRUTS EXPLODED, WITHOUT PROVOCATION OR WARNING. THE CAR WENT TO DRIVING FINE TO TERRIBLE, PAINFUL, AND TIRING. AND IT SEEMS THIS IS A COMMON PROBLEM.

NHTSA ID

11204274

Incident

Apr 27, 2019

Mileage

184,000 mi

THE SEAT WARMER WAS TURNED ON AND THE SEAT CAUGHT FIRE. SMOKE FILLED THE CABIN OF THE CAR. THE RESULT WAS A HOLE IN THE SEAT OF THE CAR. *TR

NHTSA ID

10563658

Incident

Feb 10, 2014

Mileage

104,000 mi

MY GL 320 ? 2007 LOST ALL ELECTRICAL POWER AND THE ENGINE STALLED WHILE BEING DRIVEN. THE POWER COMES BACK ON IN 10 TO 20 SECONDS AND THE CAR CAN BE RESTARTED. THIS HAPPENED 3 TIMES DURING THE FIRST 10 DAYS OF OCT 2009 WHEN THE MILEAGE WAS JUST UNDER 30,000. NOTE THE POWER STEERING AND BRAKE ASSIST GO OUT COMPLETELY AS DO THE HEADLIGHTS. ON ONE ACCESSION AT NIGHT ON A CURVE I WENT OFF THE ROAD BEFORE BEING ABLE TO STOP. ON ALL OCCASIONS THIS HAPPENED 15 TO 20 SECONDS AFTER APPLYING THE BRAKES TO DEACTIVATE THE SPEED CONTROL AND AFTER COASTING TO LESS THAN APPX. 40MPH. THE DEALER COULD FIND NO DIRECT CODE INDICATION FOR THE PROBLEM BUT DID FIND NUMEROUS LOW VOLTAGE CODES AND CHANGED OUT A NUMBER OF FUSE AND REFUSE BOXES AND FUSES. THE CAR HAS BEEN DRIVEN ONLY 100 MILES SINCE THE DEALER WORK AND THE PROBLEM HAS NOR RECURRED. *TR

NHTSA ID

10290226

Incident

Oct 4, 2009

Mileage

29,100 mi

DRAMATIC EXPLOSIVE FAILURE OF THE RIGHT ADAPTIVE SUSPENSION STRUT AIRBAG WHILE VEHICLE WAS STANDING IN THE DRIVEWAY WITH THE ENGINE ON. THE VEHICLE WAS TOWED TO A DEALERSHIP SERVICE DEPARTMENT WHERE THE STRUT WAS REPLACED AND THE FAILED PART WAS RETURNED TO MBUSA FOR INSPECTION. I HAVE HIGH QUALITY DIGITAL PHOTOS OF THE INCIDENT WHILE THE VEHICLE WAS STILL IN THE DRIVEWAY, IF NHTSA WOULD LIKE THEM, BUT UNFORTUNATELY NOT OF THE REMOVED, DAMAGED STRUT. *TR

NHTSA ID

10274357

Incident

Apr 27, 2009

Mileage

57,453 mi

ON THE 2007-2008 MERCEDES GL THE DRIVER AND PASSENGER SIDE AC VENT CLOSEST TO THE SIDE WINDOWS ALLOWS AIR TO BE DIRECTED THE VENT ON THE DOOR (WHICH SHOULD BE USED FOR DEFROST ONLY); THIS THEN FOGS UP THE SIDE WINDOWS, MAKING IT IMPOSSIBLE TO SEE THE SIDE MIRRORS WHENEVER THE AC IS ON. THIS IS CERTAINLY A HUGE SAFETY PROBLEM IN HOT HUMID AREAS LIKE HOUSTON. I HAVE HAD TO DUCT TAPE THE VENT TUBE IN ORDER TO KEEP THE VENTS FROM FOGGING UP THE SIDE WINDOWS AND BLOCKING THE VIEW OF THE SIDE MIRRORS. THIS WAS REPORTED TO MERCEDES USA A YEAR AGO, ACCORDING TO MY LOCAL DEALERSHIP, BUT MERCEDES USA HAS YET TO FIX THIS DANGEROUS DESIGN DEFECT. *TR

NHTSA ID

10219855

Incident

Mar 20, 2007

Mileage

14 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system • Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. • If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system • Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. • If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. • The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) • Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation• If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: • LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. **NOTE - As of Sept 2025 the pressure testing tool is not finalized and may require modifications to fit properly. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts