2025 Mercedes-Benz GLA 250 4MATIC

Complaint Intermittent shift feel or thud/clunk noise perceived, such as a brief jerk or transmission reaction during certain driving situations. May be most noticeable when transitioning from a coasting condition to accelerator pedal application. May occur in all drive modes. Cause Dual‑clutch transmissions (DCT) inherently exhibit more dynamic shifting behavior compared to other types of transmissions. This is due to the use of physical clutches for starting and gear changes. In certain situations, dynamic driving behavior can lead to a slight jerk sensation which is a normal technical characteristic of the transmission. A typical example is a "Change of Mind" situation: • The customer is coasting towards a red traffic light. • The traffic light turns green while the vehicle is still coasting. • The customer then presses the accelerator pedal. In these situations, a slight jerk may occur briefly because the transmission must quickly engage the appropriate gear and control the clutches accordingly. Since shift forks are responsible for engaging the gears during shifting, a slight shifting noise may also be noticeable. Please note driving programs S, S+, and M are designed to provide sportier vehicle behavior and are not optimized primarily for maximum comfort, so this operation may be more audible. Remedy Verify the customer's concern and confirm proper transmission operation. If no faults or abnormal operating conditions are identified by IPR (Intelligent Predictive Repair), no hardware replacement is necessary. Inform the customer that the transmission has been designed to provide direct gear engagement and responsive vehicle performance. Under certain operating conditions, brief shift sensations may be perceptible and are consistent with the operating characteristics of the dual‑clutch transmission

Complaint Temporary no start condition with check engine light and multiple warning messages. When performing a quick test, the following fault code is stored in Y3/14 ‑ Transmission control for 8‑speed dual‑clutch transmission (DKG): P24F100 The wake‑up line of the control unit has a short circuit to positive. Cause Possible signal timing between EZS control unit and Transmission Control Unit (DKG) Remedy As of 7/15/2026, new SCN coding is available for the EZS control unit. IPR will advise to open a TIPS case for EZS (N73), this is due to GLA models requiring support for SCN coding procedure. GLB (X247) and CLA (118) No TIPS case necessary. 1. SCN coding of EZS Control Unit 2. Clear all faults and perform extended road test with multiple drive cycles GLA (H247) Special function password required. 1. Verify if special procedure Central Locking ‑ Development Data is present in EZS (figure 1) 2. Submit a TIPS case to the Powertrain Inbox with the following information: ‑ Initial Quick Test w/ freeze frame data ‑ IPR Result ‑ DKG Control Unit Log ‑ EZS Control Unit Log ‑ Initial EEPROM data ‑ EZS special procedure menu If the vehicle has had this LI performed and P24F100 has returned, please submit a TIPS case to the Powertrain Inbox.

Complaint Frequent rear view camera flap actuations and/or noise associated. NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. Cause Calibration of the reversing camera is in progress. This is not a malfunction, but an intended system behavior. Remedy An optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Open an XSS case requesting addition of the option code "0O1" (Zero, "O", "1"). Once the option code has been added, perform the below based on which option codes the vehicle has. FOR VEHICLES WITH 235 ONLY: 1) Update and SCN code N62/* (PARK Control Unit) 2) Perform verification that optimization is as‑expected as seen below. FOR VEHICLES WITH 235 + 501: 1) Update and SCN code A26/17 (Head Unit) 2) Update and SCN code N62/* (PARK Control Unit) 3) Perform verification that optimization is as‑expected as seen below. IMPORTANT NOTE for vehicles with 235 + 501 ONLY: *For vehicles with 235 only, the "Movable 3D View" is not available due to not having 360 camera feature. Therefore the view was never present.* After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. View PRIOR to SCN Coding: View AFTER SCN Coding: Prior to releasing the vehicle, please verify the following: • Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will re‑open, when calibrating, at 9 MPH. • The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double‑clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") • an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the “Lock button", then double‑click the “Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.

Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, September 10th, 2026. After September 10th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.