2016 Mercedes-Benz GLE300D

WHILE DRIVING AT NIGHT THE VEHICLE HEADLIGHTS ARE VERY DIM. ON A DESERTED ROAD SUCH AS THE ROAD THROUGH DENALI NATIONAL PARK VISIBILITY IS APPROXIMATELY 40 TO 50 FT. AT NIGHT. ALSO BECAUSE OF THE NATURE I IF THE BEAM SEEING MORE THAN 15FT. IN FOG OR SNOW IS EXTREMELY IMPEDED. THE BEAM CREATES A HALO STARTING AT 15FT. FROM VEHICLE THAT REFLECTS IN THE FOG AND CREATES AN OPTICAL ILLUSION.

NHTSA ID

11398835

Incident

Feb 20, 2021

Mileage

103,000 mi

THE COMMAND HUB WILL NOT CONNECT.

NHTSA ID

11361447

Incident

Aug 26, 2020

SINCE THE TIME I PURCHASED THIS CAR, THE BRAKES HAVE REPEATEDLY MADE LOUD SQUEALING NOISES. MERCEDES HAS REPEATEDLY EXAMINED THE CAR AND TOLD US IT IS FINE AND NOT DANGEROUS. THEY HAVE NEVER FIXED THE NOISE. HOWEVER, MORE RECENTLY IN DECEMBER 2019, THE CAR DEVELOPED A STRONG FUEL ORDER IN BOTH THE CABIN AND OUTSIDE THE VEHICLE. WE BROUGHT IT TO A MECHANIC WHO SAID IT WAS A PROBLEM WITH THE CLAMP AND THE FUEL LINE. HE CALLED THE LOCAL MERCEDES DEALER WHO TOLD HIM TO ADJUST THE CLAMP. THAT HAS NOT FIXED THE PROBLEM. THE SMELL IS VERY STRONG, AND I AM SCARED TO DRIVE THIS VEHICLE. FROM ONLINE SEARCHES, I HAVE FOUND OTHER PEOPLE SEEM TO BE EXPERIENCING THE SAME TYPE OF PROBLEM WITH MERCEDES CARS.

NHTSA ID

11299184

Incident

Dec 20, 2019

Mileage

54,000 mi

THE REAR COLLISION ALERT SYSTEM HAS A DESIGN FLAW. THE SOUND ADJUSTED BY TECHNICIAN TO 100% IS BARELY AUDIBLE BY THE DRIVER, AND TYPICALLY AT OR AFTER IMPACT. IT IS ALSO NOT LINKED TO THE CAR DASH SOUND SYSTEM, SO THE RADIIO DOES NOT SHUT OFF ITS VOLUME. IN THIS INSTANCE, THE AUDIBLE ALARM IS INAUDIBLE. I HAVE HAD TWO ACCIDENTS WITH THE VEHICLE WHILE IT IS IN MOTION. THE DEALER DOES NOT ARGUE WITH MY ASSESSMENT, BUT SAYS THE SYSTEM IS FUNCTIONING AS DESIGNED. ATTACHED IS MY MERCEDES SERVICE RECORD DATED 10-23-2018 EXPECTING THE PROBLEM TO BE CORRECTED BY DEALER PROGRAMABLE TECHNOLOGY. I ADVISED THE SERVICE MANAGER THAT HE MIGHT WANT TO DISCUSS THIS WITH MERCEDES BEFORE I FILED THIS REPORT. HE DECLINED. THIS IS NOT A SAFE CONDITION AND COULD RESULT IN SERIOUS INJURY OR DAMAGE.

NHTSA ID

11142468

Incident

Oct 23, 2018

Mileage

20,000 mi

TL* THE CONTACT OWNS A 2016 MERCEDES-BENZ GLE300D. WHILE DRIVING 40 MPH, THE ENGINE BEGAN MAKING A LOUD NOISE. THE CONTACT STATED THAT THE ENGINE AND TRANSMISSION MOUNTS FAILED WITHOUT WARNING. THE VEHICLE WAS TAKEN TO MERCEDES-BENZ OF EL DORADO HILLS (1000 MERCEDES LN, EL DORADO HILLS, CA (888) 773-3154) WHERE IT WAS DIAGNOSED THAT THE ENGINE AND TRANSMISSION MOUNTS NEEDED TO BE REPLACED. THE CONTACT CALLED THE MANUFACTURER AND WAS INFORMED THAT THE FAILURE WAS COMMON WITH MERCEDES-BENZ VEHICLES; HOWEVER, THERE WAS NO EXTENDED WARRANTY. THE FAILURE MILEAGE WAS 35,000.

NHTSA ID

11090294

Incident

Apr 12, 2018

Mileage

35,000 mi

AFTER STOPPING, WHEN THE CAR TRANSMISSION IS IN DRIVE MODE. IF THE DRIVER PRESSES THE KEYLESS IGNITION BUTTON TO OFF, THE CAR TRANSMISSION SWITCHES TO NEUTRAL MODE. THIS CAUSES ROLLOVER RISK. IF THE DRIVER DOES NOT SEE THAT THE CAR IS IN NEUTRAL, THE CAR CAN ROLL AND CAUSE COLLISION AND RISK TO PEOPLE AROUND. THE CAR SHOULD EITHER STAY IN DRIVE MODE OR SWITCH TO PARK MODE WHEN THE OFF BUTTON IS SWITCHED WHEN THE CAR IS IN DRIVE MODE.

NHTSA ID

10983145

Incident

Apr 25, 2017

Mileage

21,000 mi

THE LEFT SIDE EXTERIOR MIRRORS DO NOT PIVOT OUT FAR ENOUGH TO ALLOW THE DRIVER TO SEE THE BLIND SPOT BESIDE THE REAR SECTION OF THE VEHICLE IF THE DRIVER HAS HIS SEAT MOVED IN THE REAR-MOST POSITIONS. THIS HAS CAUSE SEVERAL NEAR-HIT SITUATIONS WITH ME WHEN MERGING INTO TRAFFIC. EVEN THOUGH A VEHICLE WAS PRESENT IN THE BLIND SPOT NOTHING WAS VISIBLE IN ANY OF THE MIRRORS NOR WAS THERE ANY INDICATION FROM THE BLIND SPOT MONITOR. THE MIRROR NEEDS TO PIVOT ABOUT 10 DEGREES FARTHER TO ALLOW THE DRIVER VISIBILITY OF THE BLIND SPOT OR THE MIRROR NEEDS TO BE CONVEX TO INCREASE THE FIELD OF VIEW OF THE MIRROR.

NHTSA ID

10923851

Incident

Jul 9, 2016

Mileage

5,000 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304