2023 Mercedes-Benz Redundant EQS 450

The vehicle went to catch on fire and the electrical socket burnt so it could no longer charge. The airbag showed malfunction passenger side door. Multiple times the collision warning has malfunction and alerted there was a collision when none occurred.

NHTSA ID

11679815

Incident

Mar 26, 2025

Active Emergency Stop Assist Inoperative warning has shown up more than once and the dealer can not duplicate the warning or repair. It is causing frequent phantom braking and sudden stops both in normal driving use and cruise control.

NHTSA ID

11674402

Incident

Jul 7, 2025

Car turns off completely while driving with "Battery malfunction" and "Towing not permitted" error. This happened while driving on a highway at the end of a bridge going downhill so I was able to pullover to the shoulder before the vehicle came to complete stop but if this happened while on the bridge going uphill, that could've been extremely dangerous as there was no shoulder to pull over to. This has happened about 5 times already and we've taken it to the dealership. They upgraded the vehicle's software at one point saying that would address the issue, but the issue keeps happening. I don't feel safe driving this vehicle knowing that the vehicle can come to a complete stop at any time without any warning.

NHTSA ID

11651560

Incident

Mar 29, 2025

The contact owns a 2023 Mercedes-Benz EQS 450. The contact stated that while attempting to charge the vehicle, the contact became aware that the vehicle failed to begin charging as expected. After a visual inspection, the contact observed that the charging port appeared to be damaged, showing signs consistent with electrical burns. The messages "Charging station fault" and "Limited availability" were displayed. No warning lights were illuminated. The vehicle was taken to the dealer but was not yet diagnosed. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 24V372000 (Electrical System); but the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was 16,000. The VIN was not available.

NHTSA ID

11651117

Incident

Mar 27, 2025

Mileage

16,000 mi

The contact owns a 2023 Mercedes-Benz EQS450. The contact stated while driving over a bump in the roadway and depressing the brake pedal, the vehicle failed to immediately stop, causing the braking distance to become extended. The contact stated that the failure occasionally occurred while braking without driving over a bump in the roadway. The vehicle was taken to the local dealer who was unable to duplicate the failure. The vehicle was not repaired. The manufacturer was not yet contacted. The failure mileage was 1,000.

NHTSA ID

11616387

Incident

Sep 15, 2023

Mileage

1,000 mi

So I've had to have 1 tire replaced already working on number 2. First one not sure what the problem was, but this tire is having problems holding air. It'll hold air for about 9 hours then the gauge on inside of car comes in saying low tire pressure.

NHTSA ID

11615686

Incident

Aug 23, 2024

Complaint Yellow instrument cluster message: "Cooling system fault, operating energy input reduced, service required". Cause Fault code "B3A0077 - The regulation valve in the refrigerant circuit for the battery cooling gets stuck open. The ordered position cannot be achieved" stored. Faulty expansion valve component part Y140/1 Remedy Check the part number of Y140/1. If the vehicle has A 297 830 79 03 or older, replace Y140/1 with A 297 830 89 03 or newer. Do not replace defective components with part number A 297 830 8903 and an expansion valve production date after February 1, 2025! Please create TIPS case, attach the current quick test and attach picture of the evaporator assembly component part label and a picture of the production date of the EXV Y140/1 (see exampled attached).

Complaint At low speeds and light brake pressure, brakes will make a groaning or honking noise. Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal brake pad and brake rotor vibrations. Exchanging brake components will not rectify.

Complaint Crackling and cracking noise from the outer wheel on the front axle when cornering Cause The noise is generated by a micromovement on the contact surface between the rim and the brake disk (wheel bolt group) and may be intensified by potential soiling. The more lightweight rim (AMG forged rim) transmits the noise louder; in the case of cast rims, the noise is generally not perceptible. This is not a technical defect, but rather a complaint concerning comfort. Safe operation of the vehicle is ensured at all times. Remedy Important note: The operations described below do not represent a permanent remedy in every case. The noise may reoccur again after an indefinite period of time; sanding the rims with abrasive media multiple times is not permissible. Only cleaning using the Hazet tool 4960-160 (recommendation) can be performed without any concerns each time the wheel is changed or if the complaint reoccurs. Replacing the parts (rim, wheel bolts, wheel bearings, wheel hub, brake disk) is not expedient in the event of this complaint. Clean the components of the wheel bolt connection according to the WIS instructions Sand down the rim and brake disk bowl by performing the following steps: • Manually sand rim (old design only) in area of water drain bores (Figure 1; item A), approx. 1.5 cm left and right of water drain bore (Figure 2) Note: Use abrasive paper with grit size 80. The grooving in this area should no longer be visible (sand down approx. 0.1-0.2mm) • Also sand brake disk bowl using emery cloth or abrasive paper with a grain size of 120 • For vehicles equipped with the AMG ceramic brake system (B07), abrasive paper may not be used for cleaning on the brake disk side Note: Do not use any cleaning agent when cleaning on the rim side. Cleaning using abrasive paper with a grain size of 80 will suffice. Do not apply any grease, lubricant or paste after cleaning The brake disk bowl should be "bare metal" in the area of the imprints made by the hole (Figure 3)

Complaint The "Easy entry and exit feature" function deactivates itself after a brief period. (see attachment). Cause The cause is currently being investigated. Remedy Update the HU7 to the latest software version, then perform a factory reset of the HU7. Steps to perform factory reset: Navigate to Settings > System > Reset > Reset to factory settings and confirm. If the problem persists, please record HU7 log and also a trace of the Body CAN (For Star 2 Body Can 1 and for Star 3 Body Can 2) during the symptom and send via a TIPS case to the Telematics team. Note: Only collect and submit the log and trace if the symptom can be reliably reproduced.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Note: In this case, do not use the damage codes for the speakers in the warranty claim.

Complaint The OTA software update prepares the SRS/ORC controller and enables it to be updated remotely in the future. Based on technician feedback, the OTA (code: 25P5496529) does not start even after an extended period of time and several driving cycles. In addition, the "Continue" button is grayed out. Cause The exact cause for the OTA not to start is currently under analysis. Remedy Please check whether the vehicle is affected by the field measure "Update software of Supplemental Restraint System (SRS) control unit" (code: 25P5496529) and if yes, perform this update using a XENTRY with all latest Add-Ons and bill under accounting number 5496529. If the vehicle is not affected by this field measure, in the event of a complaint update control unit ORC223 (N2/5 -Supplemental Restraint System SRS) using XENTRY and use damage code 8251M01. As of XENTRY Release Version 06/25, control unit ORC223 can also be updated in this context without a password. Provided control unit ORC223 is error-free after the update, the vehicle can be handed back. ***IMPORTANT*** -In isolated cases, the OTA update may continue to be displayed for up to 3-4 weeks even after flashing with XENTRY. Note: This LI applies only to the OTA update for occupant protection!