2024 Mercedes-Benz S 580

255/35R21 Unknown Bump on tire causing it to run flat.

NHTSA ID

11735535

Incident

May 4, 2026

I am reporting a recurring transmission/drivability issue with my 2024 Mercedes-Benz S580. The vehicle has been experiencing a harsh, abnormal shift between approximately 3rd and 4th gear at around 25–35 mph during normal acceleration. The shift feels like a sudden jerk or hesitation and does not feel consistent with normal operation. The vehicle has been taken to an authorized Mercedes-Benz dealership multiple times for this issue. On a recent visit (February 9, 2026), a drive technician rode along and personally experienced the harsh shifting during a test drive. The dealership later confirmed in writing that the harsh shift was duplicated and documented on the repair order. Despite prior service visits, the problem continues to occur intermittently. It has happened again after the most recent service. In addition to the shifting concern, the vehicle has previously experienced power-related issues and steering/driver-assist warnings. There are not always warning lights before the harsh shift occurs. The vehicle remains available for inspection. Because the shifting happens during normal acceleration at city speeds, it feels unpredictable and concerning from a safety standpoint.

NHTSA ID

11719416

Incident

Feb 9, 2026

While driving my 2024 Mercedes-Benz S580, I have experienced multiple serious safety issues affecting both the power train and the wheels/tires. 1.Power Train / Transmission Failure: On two separate occasions at freeway speeds, the vehicle suddenly lost all power and came to a complete stop in the middle of the lane. I could not accelerate, steer to safety, or coast to the shoulder. The car was completely unresponsive while traffic was passing at high speed around me. I repeatedly turned the car off and back on, but it would not move for several minutes. This was extremely dangerous and created a serious risk of a rear-end collision. •The issue has been inspected and documented by Fletcher Jones Motorcars (authorized Mercedes-Benz dealer) but has not been permanently resolved. •No warning lights or messages appeared before the loss of power. •The vehicle remains available for inspection. 2.Wheels / Tires / Suspension Defect: The factory 21-inch AMG V-multispoke wheels with Pirelli MO-spec tires have experienced repeated blowouts and rapid pressure loss—approximately 6 incidents over the past 18 months of me owning this car. These occurred during normal driving and required multiple replacements at Mercedes-Benz dealerships and an independent repair shop. •The problem has been confirmed by Fletcher Jones Motorcars and Doza Garage (independent service center). •The vehicle is available for inspection. •Warning messages such as “Check Tires” and “Tire Malfunction” appeared after pressure loss was already occurring, not beforehand. •Mercedes-Benz has not identified or provided a permanent remedy. Both defects pose severe safety risks to occupants and other drivers. The transmission failures caused complete power loss in live freeway traffic, and the repeated tire malfunctions continue despite multiple replacements. The vehicle remains unsafe to operate, and all related records are available upon request.

NHTSA ID

11694946

Incident

Oct 15, 2025

Complaint Check Engine Light ON with DTC P012800 "The Coolant Temperature is Below the Specified Temperature" active and/or stored in the ME (N3/10). There are no drivability concerns related to this complaint. Cause Root cause varies Remedy Prior to performing any repairs for this complaint: With a cold engine, pressurize the high temp coolant circuit and while it's under pressure, release the cap on the low temp coolant circuit and check if the pressure drops right away or not. If the pressure drops, the lower coolant hoses are swapped. Correct this, fill, bleed and test drive the vehicle. If the complaint returns, then continue with the steps below. IMPORTANT: Use VMI to check for the following emission extended warranty –> Engine Thermostat (incl. software update) MY19-23, Various Models and Platforms (167, 190, 205, 213, 217, 222, 223, 232, 253, 290, 463) If the vehicle is covered under the above emission extended warranty, please perform steps outlined in the accompanying NCU prior to those outlined in this document. If vehicle is not covered under the above emission extended warranty or the complaint continues to occur, then proceed as follows: Check for available software updates to the ME (N3/10). If updated software is available, perform the update, clear the DTC and the perform each of the "WARM START" and "COLD START" test drives listed below twice. If the code does not re-appear then release the vehicle. If there is no new software available OR the DTC returns after the test drives then perform the following steps: • Drain the coolant through a fine mesh sieve and check for signs of debris. Additionally, inspect the coolant reservoir for debris. If any debris is found take pictures of the reservoir and the mesh filter and "flush" the system at least 2-3 times to clear as much of the debris as possible • Replace the thermostat and bleed the system as outlined in AR20.00-P-1142-04A, evacuate the system for 20-30 minutes instead of the 5 minutes specified in step 22 • NOTE: Please use all the tools specified in the AR document. The DTC will continue to populate if the circuit is not properly bled • NOTE: There are two valid thermostats to choose from in the parts section of this LI. Please verify which PN is applicable for the vehicle being worked on via XENTRY Parts Information • After bleeding the system clear the DTC and perform each of the "WARM START" and "COLD START" test drives listed below twice. If the DTC does not reappear after the tests, release the vehicle If the ME (N3/10) software is up to date, the thermostat has already been replaced, and the complaint persists open a TIPS case and attach the following documents: • Initial quick test • ME (N3/10) control unit log • The results of an R48 test from a “yes” response and from a “no” response • Pictures of the coolant reservoir and mesh sieve (mentioned above) WARM START · Begin with the engine coolant temperature at approximately 50 degrees C · Activate the AC system, if defrost is not in use open the windows · Drive the car normally until a coolant temperature of 75 degrees C is achieved · Depress the accelerator pedal 50% for ~5 seconds (partial acceleration) · Let off the accelerator pedal and let the car coast for ~10 seconds · Continue to drive the car normally COLD START · Drive for ~7 miles (normal driving) · Shut off the engine in a parking lot (or similar), wait 30 seconds, then restart and continue driving · Depress the accelerator pedal 50% for ~5 seconds (partial acceleration) · Let off the accelerator pedal and let the car coast for ~10 seconds · Continue to drive the car normally

Complaint Complaints of a harsh 3to4 upshift Cause Lost torque adaptation values and negative fill times of clutch K27. Remedy Short-term measure: Note: All steps—including resetting the learned values and performing the stationary adaptation—must be completed to resolve the concern. 1. Perform IPR and follow the provided instructions. 2. Perform software update if available (IPR will automatically check for status of software availability) 3. Perform Special Function "Resetting of learned values 'Deceleration Mode'" (VGS > Special Procedures > Special procedure > Resetting learned values Deceleration mode) 4. Complete the standstill adaptation Long-term measure: A software resolution has been released for several model years with software levels 22A.3 (n3g222aa03ub) and 22A.4 (n3g222aa04ub). - Check VGS control unit log or eeprom .txt file for "Program Status" to determine your vehicle. Software is in the approval process for MY23 with 22A.3. Once the software is released, an update on availability will be added in IPR and in this LI document. As of 6/8, software released for the following model years: MY26 with 22A.4 A001 902 25 21 >> A001 902 96 21 MY24+MY25 with 22A.3 A000 902 26 99 >> A001 902 97 21 If the vehicle software level is not 22A.3 or 22A.4: A software resolution will not be created for these vehicles, please follow the short term solution to alleviate the concern.

Complaint Crackling and cracking noise from the outer wheel on the front axle when cornering Cause The noise is generated by a micromovement on the contact surface between the rim and the brake disk (wheel bolt group) and may be intensified by potential soiling. The more lightweight rim (AMG forged rim) transmits the noise louder; in the case of cast rims, the noise is generally not perceptible. This is not a technical defect, but rather a complaint concerning comfort. Safe operation of the vehicle is ensured at all times. Remedy Important note: The operations described below do not represent a permanent remedy in every case. The noise may reoccur again after an indefinite period of time; sanding the rims with abrasive media multiple times is not permissible. Only cleaning using the Hazet tool 4960-160 (recommendation) can be performed without any concerns each time the wheel is changed or if the complaint reoccurs. Replacing the parts (rim, wheel bolts, wheel bearings, wheel hub, brake disk) is not expedient in the event of this complaint. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Clean the components of the wheel bolt connection according to the WIS instructions Sand down the rim and brake disk bowl by performing the following steps: • Manually sand rim (old design only) in area of water drain bores (Figure 1; item A), approx. 1.5 cm left and right of water drain bore (Figure 2) Note: Use abrasive paper with grit size 80. The grooving in this area should no longer be visible (sand down approx. 0.1-0.2mm) • Also sand brake disk bowl using emery cloth or abrasive paper with a grain size of 120 • For vehicles equipped with the AMG ceramic brake system (B07), abrasive paper may not be used for cleaning on the brake disk side Note: Do not use any cleaning agent when cleaning on the rim side. Cleaning using abrasive paper with a grain size of 80 will suffice. Do not apply any grease, lubricant or paste after cleaning The brake disk bowl should be "bare metal" in the area of the imprints made by the hole (Figure 3)

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Do not replace parts. Please open a TIPS case to the Body/Chassis/Entertainment inbox but read the below carefully: • The vehicle must be exhibiting the concern as shown in the attachment videos. • The vehicle DOES NOT need to be at the dealer, nor does it need to be brought into the dealership. • If the geographic location is known, it is very important that it is provided. • Provide any pictures or videos, if available. A new software for the head unit is scheduled for tentative release in Q3 2026.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.