2017 Mercedes-Benz S550E

NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

Complaint Intermittent shift feel or thud/clunk noise perceived, such as a brief jerk or transmission reaction during certain driving situations. May be most noticeable when transitioning from a coasting condition to accelerator pedal application. May occur in all drive modes. Cause Dual‑clutch transmissions (DCT) inherently exhibit more dynamic shifting behavior compared to other types of transmissions. This is due to the use of physical clutches for starting and gear changes. In certain situations, dynamic driving behavior can lead to a slight jerk sensation which is a normal technical characteristic of the transmission. A typical example is a "Change of Mind" situation: • The customer is coasting towards a red traffic light. • The traffic light turns green while the vehicle is still coasting. • The customer then presses the accelerator pedal. In these situations, a slight jerk may occur briefly because the transmission must quickly engage the appropriate gear and control the clutches accordingly. Since shift forks are responsible for engaging the gears during shifting, a slight shifting noise may also be noticeable. Please note driving programs S, S+, and M are designed to provide sportier vehicle behavior and are not optimized primarily for maximum comfort, so this operation may be more audible. Remedy Verify the customer's concern and confirm proper transmission operation. If no faults or abnormal operating conditions are identified by IPR (Intelligent Predictive Repair), no hardware replacement is necessary. Inform the customer that the transmission has been designed to provide direct gear engagement and responsive vehicle performance. Under certain operating conditions, brief shift sensations may be perceptible and are consistent with the operating characteristics of the dual‑clutch transmission

Complaint During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time. OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: ‑ Hitting the curb/posts with the front wheels. ‑ Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). ‑ Cracks (1) ‑ High pressure cleaner (2) ‑ Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double‑clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") • an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the “Lock button", then double‑click the “Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.

Complaint A popup is seen on the HU with the message "data connection temporarily not available". Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.Navigation 7.iHeartRadio 8.Traffic Cams Cause MB Apps is sundowned for all vehicles with NTG4.5 and NTG5 Head Unit Variant. Remedy No support available for NTG4.5 and NTG5 Head Unit Variants for MB App related topics. Note: Please do not create TIPS. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).