2023 Nissan Titan Xd

The contact owns a 2023 Nissan Titan XD. The contact stated that while driving at an undisclosed speed, the vehicle came to an abrupt stop and then lunged forward independently. Additionally, the contact stated that the transmission inadvertently downshifted. The vehicle was taken to the dealer; however, the dealer was unable to duplicate the failure. The failure recurred. The contact stated that while driving 5 MPH, the contact made a left turn and the transmission inadvertently down shifted. The manufacturer was made aware of the failure. The failure mileage was approximately 5,000.

NHTSA ID

11515211

Incident

Feb 1, 2023

Mileage

5,000 mi

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual

AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions:  When contamination or foreign material adhere to the lane camera viewing window on the windshield.  When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield.  When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information:  Refer to the following pages.  Use the search keyword “blinking” in the ESM.

FLUID LEAK FROM THE FRONT DIFFERENTIAL CASE ACTUATOR MOTOR PLASTIC THREADS SERVICE INFORMATION Figure 1 Figure 2 If the front differential has a fluid leak coming from the actuator motor plastic threads (Figure 1): a. Place an alignment mark on the splined actuator body and the gear carrier (Figure 2). b. Remove the actuator and thoroughly clean the threads, making sure not to allow RTV to fall into the differential case. c. Once clean, apply Three Bond sealant to the threads, and then reinstall the actuator motor, making sure to line up the alignment marks. d. Check the front differential gear oil level and top to specification. o Refer to the ESM: TRANSMISSION & DRIVELINE > DRIVELINE > FRONT FINAL DRIVE: MA235/MA210 > PERIODIC MAINTENANCE > FRONT DIFFERENTIAL GEAR OIL DO NOT replace the front differential due to a fluid leak from the actuator motor plastic threads unless there has been consequential damage due to fluid loss (bearing failure or gear noise) to the front differential.

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)