2025 RAM 2500 Problems

Driving by myself with no load at 12:15 in the afternoon with outside temperature at 80 degrees. Vehicle started to make a large screeching sound coming from engine bay. I pulled over into a parking lot and shut off engine. Vehicle continued to make screeching sound from engine bay; I opened hood to a billowing smoke that smelled like an electrical fire. Noise and significant smoke continued for several minutes with engine off and ignition in off position.

The contact owns a 2025 Ram 2500. The contact stated that while driving after the dealer completed the recall repair under NHTSA Campaign Number: 26V059000 (Exterior Lighting, Electrical System); a message asking whether the driver wanted to connect a fifth-wheel or a conventional trailer was displayed on the instrument panel, and a yellow triangle light with two wheels underneath a trailer was displayed. The contact stated that the message and warning light were illuminated while no trailer was connected to the vehicle. The manufacturer was notified of the issue and assisted the contact in scheduling a service appointment with the dealer. The vehicle was taken to the dealer twice; however, the failure could not be duplicated. The vehicle was not repaired. The failure mileage was approximately 6,500.

See attached document for complaint.

The contact owns a 2025 Ram 2500. The contact stated that while driving after the dealer completed the recall repair under NHTSA Campaign Number: 26V059000 (Exterior Lighting, Electrical System); a message asking whether the driver wanted to connect a fifth-wheel or a conventional trailer was displayed on the instrument panel, and a yellow triangle light with two wheels underneath a trailer was displayed. The contact stated that the message and warning light were illuminated while no trailer was connected to the vehicle. The manufacturer was notified of the issue and assisted the contact in scheduling a service appointment with the dealer. The vehicle was taken to the dealer twice; however, the failure could not be duplicated. The vehicle was not repaired. The failure mileage was approximately 6,500.

Driving by myself with no load at 12:15 in the afternoon with outside temperature at 80 degrees. Vehicle started to make a large screeching sound coming from engine bay. I pulled over into a parking lot and shut off engine. Vehicle continued to make screeching sound from engine bay; I opened hood to a billowing smoke that smelled like an electrical fire. Noise and significant smoke continued for several minutes with engine off and ignition in off position.

While operating my truck under normal driving conditions, the check engine warning light suddenly illuminated without warning. Due to concerns about potential vehicle reliability and safety, I immediately brought the vehicle to the dealership for diagnosis and inspection. After evaluating the vehicle, the dealership stated that diagnostic trouble codes were present and that additional analysis of the system would be required. The vehicle remained at the dealership for approximately one week before being returned to me. Upon release of the vehicle, the dealership advised that the issue was related to multiple erroneous codes and that a software update had been performed. However, the dealership did not provide a clear explanation as to why the codes were generated, what systems were affected, or whether the condition could reoccur. I was also not provided with a complete accounting of all diagnostic trouble codes identified during the inspection. I am concerned that the dealership failed to provide full transparency regarding the diagnosis and repairs performed on this vehicle. The repair order documentation was limited in detail and appeared to omit important information regarding the discovered fault codes and the full scope of work completed. Because modern vehicle systems rely heavily on electronic control modules and software for engine operation and safety-related functions, I am requesting that NHTSA document and review this issue for potential underlying electronic or software-related defects that may affect vehicle reliability and safety.

Subject: URGENT – RAM 2500 Shutdown / Near Accident / Case #XXX Hey [XXX], The truck shut down AGAIN tonight, XXX, and I nearly got into an accident. I recorded another video and called RAM to open Case #XXX. I plan to return it tomorrow morning; please coordinate safe transport. This has been ongoing for approximately a year. My 2025 RAM 2500 intermittently shuts down while driving: the engine stops, the instrument cluster goes black, and the truck goes into Neutral, losing propulsion. Previous incidents occurred at approximately 20–80 mph, with the first within 800 miles of ownership. The instrument cluster was replaced around 16,000 miles following Stellantis engineering guidance. That did not fix it. Another shutdown occurred around 18,000 miles while transporting employees to [XXX], as documented in my August 3 summary. The dealership previously discussed a new STAR case and escalation to a Stellantis field specialist (“Top Gun”). Please confirm those actions, provide the STAR case number, and link the repair history and videos to RAM Case #XXX. I need immediate engineering escalation, a documented diagnostic plan, and a permanent, verified repair—not more trial-and-error parts replacement. Since previous failures reportedly left no fault codes, please consider long-term diagnostic logging to capture the event. I am willing to leave the truck for several weeks. My priority remains fixing it, but if Stellantis cannot resolve this, I expect a formal review of buyback or other resolution options. This is a serious, recurring safety issue that nearly caused an accident tonight. RAM’s response will directly affect our company’s future business with the brand. Please confirm receipt INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Our 2025 Ram Rebel stalled on a 55-mph curve on a busy freeway. Fearful, I deliberately drifted the vehicle to the right side of the road looking for an emergency lane. The truck regained momentum and I drove it another 10 miles. Coming to a stop, I heard mechanical griding and felt the truck shudder. I drove it home. My husband took the truck, and the same griding and shuddering happened to him twice over a 15-minute period while driving on surface streets less than 20 mph. The truck did not stall on him. -We have been told by the dealership that the transfer case failed. The dealership is working to fix it. -My safety and those riding in my vehicle were put at significant risk due to the stall on the freeway and a transfer case failure. -The problem was confirmed by an official Ram dealer where we purchased the vehicle. -The transfer case failure has been inspected but the reason for the stalling has not been identified. -A warning light "Service 4WD" turned on each time we heard the grinding sound but then turned off. We bought the vehicle new, have owned it 11 months and it has $15,000 miles. All services have been conducted according to the maintenance schedule.

I have a 2025 ram 2500 diesel, and I use it to tow, as I am a farmer, and have a farm. I pull stock trailers, my tractor, and other trailers associated with my farm. I took my truck in for the trailer tow module recall to be done over 4 months ago, and they said they had to order the part and would call once it came in. It has now been over 4 months, I have called the dealer to follow up, and keep getting the same answer. The part hasn't arrived yet, and they will call me when it comes in. Every time I hook up a trailer it disables my trailer brakes, throws the AEB light on, and I am afraid, that in the instance I have to stop abruptly, that I may crash, and or hurt or even Kill someone due to these issues. I'm at a loss, they are worried about doing the trucks on the lot before they take care of the ones on the road per Jeremy at the Crain Ram dealership in Hot Springs, AR, which I don't feel is right to do. They got my money, now I have to deal with the issue, and potentially worse, until they get their unsold trucks done on the lot. Any help would be GREATLY appreciated!

I am filing a safety complaint regarding a persistent soft brake pedal condition affecting my truck. Under normal driving conditions and especially during low-speed braking with no trailer or payload attached, the brake pedal feels excessively soft and requires additional pedal travel before adequate braking response occurs. The authorized dealer inspected the vehicle and replaced the brake pads and resurfaced the rotors; however, the soft brake pedal condition continues unchanged. After further evaluation, the dealer stated that their engineer determined the vehicle is operating within factory specifications and declined to pursue any additional diagnosis or repairs. I use this truck for towing an RV, and due to the abnormal brake feel and reduced confidence in braking performance, I do not feel safe towing with this vehicle. As a result, the truck remains parked at my residence because I believe continued operation may present a safety risk. I have driven other trucks of the exact same year and model that exhibited significantly firmer and more responsive brake pedal feel, which leads me to believe my vehicle is not operating normally despite the dealer’s claims. In addition, I have found numerous online reports from other owners describing similar soft brake pedal complaints, including reports of lemon law claims and unresolved brake concerns. I am requesting that NHTSA investigate this issue for potential brake system defects or inconsistent braking performance that could affect vehicle safety, particularly during towing or emergency braking situations.

I have a 2025 ram 2500 diesel, and I use it to tow, as I am a farmer, and have a farm. I pull stock trailers, my tractor, and other trailers associated with my farm. I took my truck in for the trailer tow module recall to be done over 4 months ago, and they said they had to order the part and would call once it came in. It has now been over 4 months, I have called the dealer to follow up, and keep getting the same answer. The part hasn't arrived yet, and they will call me when it comes in. Every time I hook up a trailer it disables my trailer brakes, throws the AEB light on, and I am afraid, that in the instance I have to stop abruptly, that I may crash, and or hurt or even Kill someone due to these issues. I'm at a loss, they are worried about doing the trucks on the lot before they take care of the ones on the road per Jeremy at the Crain Ram dealership in Hot Springs, AR, which I don't feel is right to do. They got my money, now I have to deal with the issue, and potentially worse, until they get their unsold trucks done on the lot. Any help would be GREATLY appreciated!

Subject: Safety Concern – Vehicle Shuts Down While Driving / Request for Replacement Despite multiple warranty repair attempts, my 2025 Ram 2500 continues to experience unresolved electrical failures. In addition to the previously documented issues, the vehicle shuts down while driving, forcing me to immediately pull over, place the vehicle in park, and restart the engine in order to continue driving. This condition has occurred unexpectedly and without warning. Losing power while the vehicle is in motion presents a serious safety risk, especially during highway or interstate driving. Given that I rely on this truck for work and frequently travel long distances between New Jersey and Texas, this behavior makes the vehicle unsafe and unreliable for its intended use. The truck has already undergone repeated diagnostics, module replacements, software updates, wiring repairs, and battery replacement at authorized Ram dealerships. Despite these efforts, the issue persists. At this point, I have lost confidence in the safety and reliability of this vehicle and do not feel comfortable continuing to drive or own it. I have acted in good faith and allowed multiple opportunities to repair the vehicle. The ongoing shutdowns while driving demonstrate that the defect has not been corrected within a reasonable number of attempts. Requested Resolution: • Immediate escalation of this case due to a safety-related defect • Replacement of the vehicle or trade-assist into another Ram truck • Reimbursement for loss-of-use expenses incurred due to repeated service visits I am requesting a definitive resolution rather than additional repair attempts.

While operating my truck i have a air bag warning indicator come up on my cluster gage. With the light still one and engine running I immediately drove the vehicle to my local Ram dealer to seek assistance. I had spoken to a service advisor who checked my vehicle in for service. The service advisor did confirm the SRS light was on. After the tech did a diagnostic they found no stored service codes, the dealer cleared rhe codes, and said there was no issue and no repairs was performed. I find it very strange for the light to just randomly comon and there is no issues. I have reason to believe the dealership was not being transparent and did not provide the full scope of work performed on this truck.

My vehicle has been in to 2 different dealerships for a warning light check airbag system. I have had it in to the repair shop approximate 5 times. It's fixed for a day or 2 then the warning comes back on. There is a safety recall for this and was performed a software update which didn't solve the issue. I do not feel safe for driving this vehicle.

while driving down the road at 45 mph I lost power steering and was pulled off the road. This happened twice.Took it to the dealer and they found stored DTC , LSOS communication with BCM stored in the steering assist module.

My brand new truck started shaking while accelerating past 65mph. The shaking was not dampened by the suspension at all. (I.e. it kept the same or increased strength). The shaking could cause damage, excessive loosening or wear of critical components and lead to a serious accident at these speeds. It is similar to the "death wobble", but not as violent. It occurred multiple times. The shaking occurred without going over large bumps. I took it to a dealership and they did a load balance and alignment without resolving the problem. They noted a wheel was warped and moved it from the front to the back. This did not solve the problem. It seemed to prevent the shaking if I just tap the gas and wait a few seconds instead of holding it. The transition in and out of eco mode (4 to 8 cylinders) should be looked into.

Check engine light consistently comes on with codes p0263, p0272, p0266 for contribution balance codes for cylinders 1, 2, 4 & 5. Truck runs rough. Dealership says it’s a 5-8 week process to test and get injectors into replace if that’s the issue. Multiple sources have stated it can be a software update issue and some states still waiting after weeks for fix to be made and paying for a rental car out pocket to have reliable transportation for work and taking care of kids.

On Sunday, 9/14/25 driving on a 70 MPH interstate highway, pulling a trailer behind the Newly-purchased 2025 truck (only 700 miles on it), the road narrowed down to one lane because of a traffic obstruction and cones. As I slowed down to about 35 mph and then went to speed up again as the traffic eased, the vehicle provided a ping notification sound and the Electronic Vehicular Instrument Cluster (EVIC) display stated something to the effect of "Shift into 'P' to start vehicle". I realized that the vehicle was not responsive as expected, indicating power steering had failed, likely because the engine was off. I'm uncertain whether the steering wheel was locked, which is likely, because at that speed, only a very slight turn of the wheel was needed to move into the closed lane on the straight road. I continued to coast to get the vehicle and trailer over to the right, hugging the cones which were mid-lane in the closed lane, allowing other cars to go around me while I came to a complete stop on the interstate to shift into Park. Once I could get the gearshift into Park, I started the vehicle again, at which point it drove normally. The trailer had been weighed just that morning and both tongue and overall weight were well within the capacity of the vehicle. It was hooked up to the electrical systems of the tow vehicle via the 7-pin connector. I had the EVIC set to show vehicular information - oil pressure, oil temperature, etc. I similarly had information like battery voltage displayed on a widget on the uconnect screen. Everything looked nominal. No error code was logged to my knowledge. I have since seen similar reports from other 2025 RAM owners in NHTSA complaints and on social media. My dealership is unaware of these issues having been reported elsewhere, so they are starting from scratch in finding a diagnosis on a seemingly intermittent issue. That process is ongoing at this time.

Windshield seal leak drivers side. The windshield and seal comprise of about 60% of the structure to keep roof from collapse in an accident. A leak can cause electrical component failure Issue was brought forward to dealership, leak confirmed by dealership on 3/11/26 Dealership ordered new windshield which was finally installed on 4/9/26

Windshield wipers occasionally don’t operate correctly in the mist, wash and intermittent/auto wiper modes. The dealer has confirmed this problem and has a wiper switch on order but there are none available. Because of this being a safety issue, the vehicle has not been driven and is not operational during inclement weather.

On 11/4/25 Pepboys Tires in Pelham AL installed four new tires on my truck - BF Goodrich K03 tires. After driving 15 miles, the driver rear vehicle wheel and tire detached from the hub. All 8 lugnuts were missing and obviously had not been tightened or torqued to specifications. While Pepboys is performing the repair to my truck at a cost of approximately $2000, they seem uninterested in the risk and danger they are creating with such poor performance and lack of quality controls. They endangered me and everyone that was around me on Hwy 31 when the wheel detached. They need to be held accountable for their poor workmanship and danger to the public. It is not acceptable to me that they said that location had not had a wheel detach from a vehicle following service for 3 years. They must be better. And, must be held accountable. I have documentation of the service and pictures available for your investigation.

I have had numerous safety warning messages display upon startup and also while driving. The messages are usually combined with a cold ambient temperature and do not display during warm temperatures. The FCA dealership has attempted to fix this issue on at least six different occasions so far without any change. To date, FCA has replaced the original battery, they have updated, flashed the ECU module, performed NHTSA Recall B4C for flashing the cluster, and most recently they replaced the ORC module. FCA indicated that NHTSA-25V882 was not applicable to my VIN despite my VIN production date in April '25; within your suspect period. Original issue remains, FCA STAR case generated however cannot replicate error condition for FCA engineers. The next scheduled visit to FCA is to replace a telematics module for possible link to issue with the Uconnect5 system. This safety issue was first noted before 800 miles and continues through 2768 miles thus far. As this issue pertains directly to a vital Air Bag sensor issue and the inability to call for a SOS assistance, I expect the NHTSA to raise this concern with FCA USA and to determine the cause of this safety defect and issue a new Recall Notification for repair and/or replacement of affected parts.

My brand new truck started shaking while accelerating past 65mph. The shaking was not dampened by the suspension at all. (I.e. it kept the same or increased strength). The shaking could cause damage, excessive loosening or wear of critical components and lead to a serious accident at these speeds. It is similar to the "death wobble", but not as violent. It occurred multiple times. The shaking occurred without going over large bumps. I took it to a dealership and they did a load balance and alignment without resolving the problem. They noted a wheel was warped and moved it from the front to the back. This did not solve the problem. It seemed to prevent the shaking if I just tap the gas and wait a few seconds instead of holding it. The transition in and out of eco mode (4 to 8 cylinders) should be looked into.