RoadVitals

2025 Altec Ac Series Crane Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
Recall campaignsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
2
Newest Jun 11, 2026
Carrying an NHTSA advisoryCampaigns where NHTSA told owners not to drive the vehicle, or to park it outside, until the repair is done.
0
Open investigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0

Recall campaigns

2 campaigns cover this model year — what the defect is, what it could cause, and what the remedy is

26V384000

EQUIPMENT:MECHANICAL:BOOM/CRANE/LADDER:CRITICAL FASTENERS

Jun 11, 2026
14 units potentially affected
The defect: Altec Industries (Altec) is recalling certain 2024-2026 AC Series Crane vehicles. The inside joints between the side plates and the base plates of the 26-foot insulating personnel jib (IJ26) may be missing welds.
The risk: Missing welds can lead to platform joint failure due to fatigue or overload, resulting in the platform falling from the boom tip, increasing the risk of injury.
The remedy: Altec will advise owners to inspect the IJ26 jib for missing welds. If the welds are missing, the jib should be taken out of service immediately. Altec will add the missing welds or provide a repair procedure and kit, free of charge. Owner notification letters were mailed July 23, 2026. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is MAB-3330.
Altec Industries, Inc.Manufacturer number MAB-3330View on NHTSA.gov
26V170000

EXTERIOR LIGHTING

Mar 20, 2026
134 units potentially affected
The defect: Altec Industries, Inc. (Altec) is recalling certain 2025 AC Series Crane and DT Series Digger Derrick vehicles. The harness intended to prevent Altec installed lighting from overloading the chassis lighting circuit was not installed, which may result in a loss of power to the body lighting or trailer lights.
The risk: Loss of body lighting or trailer lights increases the risk of a crash.
The remedy: Altec will notify owners to inspect their vehicle for the harness. If the harness is missing, a repair kit will be provided, free of charge. Owner notification letters were mailed May 15, 2026. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN-3295.
Altec Industries, Inc.Manufacturer number CSN-3295View on NHTSA.gov

What a recall is

Safety recall
A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation
NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Elsewhere on this vehicle

Data sources